• 대한기계학회논문집B
• /
• 제23권2호
• /
• pp.234-242
• /
• 1999

Flow phenomena such as the pressure transients Inside a high-speed railway tunnel and the Impulsive waves at the exit of the tunnel are closely associated with the characteristics of the entry compression wave, which is generated by a train entering the tunnel. Tunnel entrance hood may be an effective means for alleviating the Impulsive waves and pressure transients. The objective of the current work is to explore the effects of the train nose shape and the entrance hood on the characteristics of the entry compression wave. Numerical calculations using the method of characteristics were applied to one-dimensional, unsteady, compressible flow field with respect to high-speed railway/tunnel systems. Two types of the entrance hoods and various train nose shapes were employed to reveal their influences on the entry compression wave for a wide range of train speeds. The results showed that the entry compression wave length increases as the train nose becomes longer and the train speed becomes lower. The entry compression wave length in the tunnel with hood becomes longer than that of no hood. Maximum pressure gradient in the compression wavefront reduces by the entrance hood. The results of the current work provide useful data for the design of tunnel entrance hood.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.861-869
• /
• 1986

본 연구에서는 동시확립문제의 속도장해석에 있어서 단면내의 속도분포에 대 한 일체의 가정을 하지 않고 운동량방정식을 직접 해석하여 단면내의 속도분포를 구하 였다. 또한 Prandtl수, 반경비 및 편심도가 열전달특성에 미치는 영향에 대한 해석 도 수행하였다.

• 한국항공우주학회지
• /
• 제34권10호
• /
• pp.71-79
• /
• 2006

액체로켓엔진에서 고주파 연소불안정을 제어하기 위하여 다단 접선 유입구를 갖는 스월 인젝터를 분석하였다. 음향흡수자로서 인젝터의 효과를 분석하기위하여 인젝터는 1/4 파장 공명기로 해석하였고, 상온에서 감쇠 효과의 적합성을 검증하였다. 이러한 인젝터는 모델 챔버의 고유주파수에 동조시킬 수 있는 고유주파수를 갖게 된다. 다단의 접선 유입구를 갖는 인젝터가 단일 유입구를 갖는 인젝터 보다 인젝터 내부의 air core가 안정되었다. 또한, 다단 접선 유입구를 갖는 인젝터를 사용하였을 때 불안정 모드에 동조되는 인젝터 길이가 계산된 길이와 잘 일치하였다. 이러한 실험 결과로부터 인젝터 내부의 air core가 안정되게 유지된다면, 동조된 스월 인젝터는 모델 챔버의 불안정 모드를 효과적으로 감소시킬 수 있고, 감쇠율을 증가시킬 수 있음을 확인하였다.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.21-29
• /
• 2004

The flow characteristics of a swirl injector were investigated with the variation of the flow condition and geometric dimensions, such as orifice length for considering the viscous effect and tangential entry port area for considering the swirl intensity. The liquid film thickness strongly influencing on the formed drop size of the spray was measured using a new technique. The film thickness measurement technique proposed here, used the attenuation of fluorescence signal near the injector exit. The breakup length that is important for the flame location as well as the spray cone angle which influences on the ignition performance was measured using a backlit stroboscopic photography technique. From the experimental results, it is found that an increase in injection pressure decreased the film thickness and breakup length, and also enlarged the spray cone angle. A decrease in orifice length and tangential entry port area has a similar tendency of thinner film thickness, shorter breakup length and larger spray cone angle. In the present study, we proposed empirical models of the flow characteristics of the swirl injectors.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.212-222
• /
• 1994

In the annular Modified Chemical Vapor Deposition process using two concentric tubes, the inner tube is heated to maintain high temperature gradients to have high thermophoretic force which can increase particle deposition efficiency. However, higher axial velocity in a narrow gap between inner and outer tubes can result in a longer tapered entry length. In the present paper, a new concept using an annular jet from the inner tube is presented and shown to significantly reduce the tapered entry length with maintaining high efficiency. Effects of a jet injection on heat transfer, fluid flow and particle deposition have been studied. Of particular interests are the effects of jet velocity, jet location and temperature on the deposition efficiency and tapered length . Torch heating effects from both the previous and present passes are included and the effect of surface radiation between inner and outer tubes is also considered.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.596-606
• /
• 2002

The three-dimensional unsteady compressible Euler equation solver with ALE, CFD code, PAM-FLOW based on FEM method has been applied to analyze the flow field around the high speed train which is entering into a channel. From the present study, the pressure and flow transients were calculated and analyzed. The generation of compression wave was observed ahead of train and the high pressure in the gap between the train and the tunnel was also found due to the blockage effects. It was found that abrupt fluctuation in pressure exists in the region from train nose to shoulder of train corresponding to 10％ of total length of train during tunnel entry. Computed time history of aerodynamic forces of train during tunnel entry show that drag coefficient rapidly rises and saturates at about non-dimensional time 0.31. The total increase of drag coefficient before and after tunnel entry is about 1.1%. Transient profile of lift force shows similar pattern to drag coefficient except abrupt drop after saturation and lift force in the tunnel increases 0.08% more than that before tunnel entry.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.943-946
• /
• 1999

In this paper, we present a new clock routing algorithm which minimizes total wirelength under any given path-length skew bound. The algorithm onstructs a bounded-skew tree(BST) in two steps:(ⅰ) a bottom-up phase to construct a binary tree of shortest-distance feasible regions which represent the loci of possible placements of clock entry points, and (ⅱ) a top-down phase to determine the exact locations of clock entry points. Experimental results show that our clock routing algorithm, named BST/DME, can produce a set of solutions with skew and wirelength trade-off.

• 한국도로학회논문집
• /
• 제14권3호
• /
• pp.173-182
• /
• 2012

휴게소 진 출입부는 설계속도 등이 급변하는 구간으로 교통안전 취약구간이며 특히, 휴게소 진입부는 감속과 주차공간 검색 두 가지 작업이 동시에 수행되므로 이용차량의 안전성을 확보할 수 있는 설계기준이 필요하다. 국내의 경우 영업소나 나들목, 분기점 같은 출입시설에 대한 기하구조 기준은 수립되어 있는 반면, 도로의 부속시설인 휴게소에 대한 상세한 기하구조 기준은 없는 실정이다. 이에 본 연구에서는 일반형 휴게소 135개소를 대상으로 한 현장조사 및 사고조사 자료를 활용하여 휴게소진 출입부 기하구조에 대한 문제점을 도출하였다. 휴게소 진 출입부의 설계구간을 분류하고 각 구간에 대한 설계요소를 도출한 후, 휴게소 진 출입부를 대상으로 속도조사 및 차량주행행태 조사를 수행하고 분석을 통해 설계요소별 최소 기준을 도출하였다. 진입 연결로의 시/종점 속도에 따라 감속거리 산정식을 이용하여 진입 연결로의 최소길이는 40m를 제안하였고, 주행행태를 기반으로 선형 안전성 평가를 통해 접속 설치각은 12~$17^{\circ}$를 제안하였다. 개발된 휴게소 진입부 설계기준은 신설되는 휴게소 뿐만 아니라 기존 휴게소에 대해 현실적으로 적용 가능한 개선방안을 제시할 수 있을 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제35권9호
• /
• pp.891-896
• /
• 2011

본 연구에서는 사각 마이크로 채널의 열전달 특성을 연구하기 위한 실험을 수행하였다. 실험에 사용된 시료의 채널 수력직경은 $700{\mu}m$이며, 채널의 개수는 20개이다. 작동유체는 물이며, 작동유체의 입구 온도는 $20^{\circ}C$ 이다. 실험 변수는 Reynolds 수 400 ~ 800 및 열 유속 35 ~ 85 kW/$m^2$ 이다. 결과로, Reynolds 수가 큰 경우일수록 대류 열전달 계수가 증가하는 것으로 나타났으며, 열적으로 완전히 발달 된 영역에 대하여 대류 열전달 계수는 약 4.6 ~ 6.4 kW/$m^2^{\circ}C$로 나타났다. 또한, 사각 마이크로 채널에서의 열적 입구길이는 Reynolds 수가 커지는 경우일수록 길어지는 것을 알 수 있었으나, 열 유속의 변화는 입구길이에 영향을 미치지 않는 것으로 나타났다. 본 연구의 결과로 완전히 발달된 유동영역에 대하여 사각 마이크로 채널의 열적 특성을 나타내기 위한 Nusselt 수 상관식을 제안하였다.

• 한국도로학회논문집
• /
• 제15권1호
• /
• pp.143-154
• /
• 2013

PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.