• Korean Journal of Materials Research
• /
• v.34 no.5
• /
• pp.254-260
• /
• 2024

This study is to manufacture a titanium dioxide (TiO₂) photocatalyst by recycling sludge generated using titanium tetrachloride (TiCl₄) as a coagulant. Compared to general sewage, a TiCl₄ coagulant was applied to dyeing wastewater containing a large amount of non-degradable organic compounds to evaluate its performance. Then the generated sludge was dried and fired to prepare a photocatalyst (TFS). Scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX), X-ray diffraction (XRD), and nitrogen oxide reduction experiments were conducted to analyze the surface properties and evaluate the photoactive ability of the prepared TFS. After using titanium tetrachloride (TiCl₄) as a coagulant in the dyeing wastewater, the water quality characteristics were measured at 84 mg/L of chemical oxygen demand (COD), 10 mg/L of T-N, and 0.9 mg/L of T-P to satisfy the discharge water quality standards. The surface properties of the TFS were investigated and the anatase crystal structure was observed. It was confirmed that the ratio of Ti and O, the main components of TiO₂, accounted for more than 90 %. As a result of the nitric oxide (NO) reduction experiment, 1.56 uMol of NO was reduced to confirm a removal rate of 20.60 %. This is judged to be a photocatalytic performance similar to that of the existing P-25. Therefore, by applying TiCl₄ to the dyeing wastewater, it is possible to solve the problems of the existing coagulant and to reduce the amount of carbon dioxide generated, using an eco-friendly sludge treatment method. In addition, it is believed that environmental and economic advantages can be obtained by manufacturing TiO₂ at an eco-friendly and lower cost than before.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.108-108
• /
• 2017

In this study, biocomposite filaments with agricultural by-products can be used in extrusion-based 3D (Three-dimensional) printing. Extrusion-based 3D printing stands as a promising technique owing to its versatility. We hypothesized that bio-filament composite consisted of something derived from agricultural by-products could be used as 3D printing materials that could overcome the drawbacks of PCL (poly-caprolactone). Bio-filament mixed with PCL and agricultural by-products was defined as r-PCL in this study. In order to find it out the optimal mixing ratio of filaments, we had investigated PCL, r-PCL 10%, r-PCL 20%, r-PCL 50% separately. The morphological and chemical characteristics of the filaments were analyzed by FE-SEM (Field emission scanning electron microscope) and EDX (Energy-dispersive X-Ray spectroscopy), and the mechanical properties were evaluated by stress-strain curve, water contact angle, and cytotoxicity analysis. Results of this study have been shown as a promising way to produce eco-friendly bio-filaments composite for FDM (Fused deposition modeling) method based 3D printing technology. Thus, we could establish biomimetic scaffolds based on bio-printer filaments mixed with agricultural by-product.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.60-65
• /
• 2008

This study aims at investigating the wear properties of thermally sprayed $Al/Al_2O_3$ metal matrix composite(MMC) coating against different counterparts. $Al/Al_2O_3$ MMC coatings were fabricated using a flame spray system on an Al 6061 substrate. Dry sliding wear tests were performed using the sliding speeds of 0.2m/s and the applied loads of 1 and 2 N. AISI 52100, $Al_2O_3$, $Si_3N_4\;and\;ZrO_2$ balls(diameter: 8mm) were used as counterpart materials. Wear properties of $Al/Al_2O_3$ MMC coatings were analyzed using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDX). It was revealed that wear properties of $Al/Al_2O_3$ composite coatings were much influenced by counterpart materials. In the case of AISI 52100 used as counterparts, the wear rate of composites coating layer increased according to the increase of the applied load. On the contrary, in the case of ceramics used as counterparts, the wear rate of composites coating layer decreased according to the increase of the applied load.

• Advances in materials Research
• /
• v.4 no.3
• /
• pp.145-164
• /
• 2015

Biodegredable and injectable nanocomposites based on polypropylene fumarate (PPF) as unsaturated polyester were prepared. The investigated polyester was crosslinked with three different monomers namely N-vinyl pyrrolidone (NVP), methyl methacrylate (MMA) and a mixture of NVP and MMA (1:1 weight ratio) and was filled with 45 wt% of hydroxyapatite (HA) incorporated with different concentrations of chemically treated natural bone powder (NBP) (5, 10 and 15 wt%) in order to be used in treatment of orthopedics bone diseases and fractures. The nanocomposites immersed in the simulated body fluid (SBF) for 30 days, after the period of immersion in-vitro bioactivity of the nanocomposites was studied through Fourier transform infrared (FTIR), scanning electron microscope (SEM), energy dispersive X-ray (EDX) in addition to dielectric measurements. The degradation time of immersed samples and the change in the pH of the SBF were studied during the period of immersion.

• Clean Technology
• /
• v.19 no.3
• /
• pp.347-350
• /
• 2013

Desorption characteristics for ions adsorbed onto sericite was performed by means of $HNO_3$ solution which was selected as the best desorbing agent in the previous work. Elution of nickel ions adsorbed onto sericite using $HNO_3$ solution was confirmed by means of scanning electron microscopy (SEM) & energy dispersive X-ray spectroscopy (EDX) analysis. Desorption efficiency for nickel ions was 100% at the 20 mM of concentration. Also, nickel ions was completely desorbed within 1.0 of S/L (mg/mL) ratio which is defined as the ratio of adding amount of adsorbent and volume of desorbing agent and desorption process was quickly carried out within 60min. Finally, removal efficiency of reused sericite for nickel ions was constantly maintained until the 4th cycle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.252-255
• /
• 2004

Various Semiconductor/Metal structured nanowires were synthesized from the simple thermal annealing of ball-milled compound powders and the thermal evaporation of metals. Their structural properties were investigated by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM), Energy Dispersive X-ray spectroscopy(EDX). Depending on the type of metals and the material of nanowires, uniform somiconductor/metal nanowires(GaN/Al, GaN/Ag) or isolated metal particles on semiconductor nanowires$(SnO_2/Ti,\;Si/Ti)$ were formed on the surface of nanowires.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.6
• /
• pp.482-485
• /
• 2017

PURPOSE. This laboratory study aimed to investigate the effect of doping an acrylic denture base resin material with nanoparticles of ZnO, CaO, and $TiO_2$ on biofilm formation. MATERIALS AND METHODS. Standardized specimens of a commercially available cold-curing acrylic denture base resin material were doped with 0.1, 0.2, 0.4, or 0.8 wt% commercially available ZnO, CaO, and $TiO_2$ nanopowder. Energy dispersive X-ray spectroscopy (EDX) was used to identify the availability of the nanoparticles on the surface of the modified specimens. Surface roughness was determined by employing a profilometric approach; biofilm formation was simulated using a monospecies Candida albicans biofilm model and a multispecies biofilm model including C. albicans, Actinomyces naeslundii, and Streptococcus gordonii. Relative viable biomass was determined after 20 hours and 44 hours using a MTT-based approach. RESULTS. No statistically significant disparities were identified among the various materials regarding surface roughness and relative viable biomass. CONCLUSION. The results indicate that doping denture base resin materials with commercially available ZnO, CaO, or $TiO_2$ nanopowders do not inhibit biofilm formation on their surface. Further studies might address the impact of varying particle sizes as well as increasing the fraction of nanoparticles mixed into the acrylic resin matrix.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.328.2-328.2
• /
• 2014

Semiconductor nanowires (NWs) have attracted research interests due to the distinct physical properties that can lead to variousoptical and electrical applications. In this paper, we have grown InAs NWs viagold (Au)-assisted vapor-liquid-solid (VLS) and catalyst-free vapor-solid (VS) mechanisms and investigated on the p-type doping profile of the NWs. Metal-organic chemical vapor deposition (MOCVD) is used for the growth of the NWs. Trimethylindium (TMIn) and arsine (AsH3) were used for the precursor and diethyl zinc (DEZn) was used for the p-type doping source of the NWs. The effectiveness of p-type doping was confirmed by electrical measurement, showing an increase of the electron density with the DEZn flow. The structural properties of the InAs NWs were examined using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In addition, we characterize atomic distribution of InAs NWs using energy-dispersive X-ray spectroscopy (EDX) analysis.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.2011-2013
• /
• 2002

일반적으로, 전도성 고분자는 금속에 준하는 전기 전도도와 다공성을 이용한 전해질 이온 및 생채 고분자의 물리, 화학적 도우핑 능력을 장점으로 한다. 따라서, 이 분야의 최근 연구동향도 이온 도우핑에 의한 전도성 고분자의 전기 전도도 향상에 초점이 맞추어져 있으며, 이미 다수의 연구진에 의행 여러 가지 방법이 제시되었다. 본 논문은 전기 화학적 cementation 공정을 이용하여 금속 이온을 전도성 고분자에 도우핑하고 특성을 고찰하였다. 전도성 고분자로써 polypyrrole (PPy)을 사용하고, micropaticles (구리와 니켈 이온)를 도펀트 (dopant)로 하여 -1.5 V ${\sim}$ 2V의 범위에서 순환 전압 전류법 (Cyclic voltammetry)을 이용해 organic-inorganic complex를 제작하였고, 각각의 전극을 비교, 분석 하였다. 구리 이온을 도우핑한 PPy 필름은 전기 전도도가 매우 우수하나 대기 중 공기 및 수분에 의해 쉽게 산화되므로 life-time이 짧다. 이를 보완하기 위하여 상대적으로 안정한 니켈 이온을 도우핑한 PPy 필름의 전기 화학적 특성을 고찰하였다. 전극의 표면은 SEM (Scanning Electron Microscopy), EDX (Energy Dispersive X-ray spectroscopy)를 이용하여 분석하였다.

• Journal of Welding and Joining
• /
• v.31 no.5
• /
• pp.64-70
• /
• 2013

The joining of Ti and SUS304 dissimilar metals is one of the effective measures to save rare metal. But Ti and SUS304 have differences in materials properties, and Ti and Fe intermetallic compounds such as TiFe and $TiFe_2$ are easily formed in weld fusion zone between Ti and SUS304. Nevertheless, in this study, full penetration lap dissimilar welding of Ti and SUS304 using single-mode fiber laser with ultra-high welding speed was tried, and it was found out that ultra-high welding speed could control the generation of intermetallic compound. To recognize the formation of intermetallic phase in the weld fusion zone and the compound zone of interface weld area were observed and analyzed using energy dispersive X-ray spectroscopy (EDX). And it was confirmed that the ultra-high welding speed could reduce amount of intermetallic compounds, but the intermetallic compounds were existed in the weld fusion zone under the all conditions.