• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.56-63
• /
• 2010

This work proposes a 12b 100MS/s 0.13um CMOS pipeline ADC for battery-powered mobile video applications such as DVB-Handheld (DVB-H), DVB-Terrestrial (DVB-T), Satellite DMB (SDMB), and Terrestrial DMB (TDMB) requiring high resolution, low power, and small size at high speed. The proposed ADC employs a three-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. A single shared and switched op-amp for two MDACs removes a memory effect and a switching time delay, resulting in a fast signal settling. A two-step reference selection scheme for the last-stage 6b FLASH ADC reduces power consumption and chip area by 50%. The prototype ADC in a 0.13um 1P7M CMOS technology demonstrates a measured DNL and INL within 0.40LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 60.0dB and a maximum SFDR of 72.4dB at 100MS/s, respectively. The ADC with an active die area of 0.92 $mm^2$ consumes 24mW at 1.0V and 100MS/s. The FOM, power/($f_s{\times}2^{ENOB}$), of 0.29pJ/conv. is the lowest of ever reported 12b 100MS/s ADCs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.855-859
• /
• 2004

The Japanese National Project "Carbon Nanotube FED" is developing a high image-quality and low power-consumption field emission display (FED) by applying carbon nanotube (CNT) to the electron source. A uniform electron source with a flat-film CNTs and fine structure triodes Fir suppressing the deviation of emission is required. For realizing an FED panel, it is also necessary to develop the glass-bulb technologies for vacuum sealing, and display technologies for driving the panel by circuit electronic and for evaluating the picture quality by measuring. By achieving these technologies, an FED compatible with conventional Cathode Ray Tubes (CRTs) will be realized.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.652-657
• /
• 1987

This paper describes an application of CMOS Gate Array Integrated Cricuits to the implementation of three functional units: A Multiplexer, Time Switch, and Demultiplexer in the Switching Network and Digital Line Concentrator of TDX-1 system, which is a fully digital time division electronic switching system in Korea. The application of CMOS Gate Array Integrated Circuits significantly improves the overall system performance in terms of power consumption, cost, size, reliability, and timing margin, etc.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.7-7
• /
• 2009

This presentation will introduce Merck's investments for business to support the future market growth as "trendsetter contributor". As the world's oldest phamaceutical & chemical company, Merck has made the seamless investment for innovation. The investment for the new technologies is being continued for new LC materials, OLED material, organic electronic materials for flexible display, more environment friendly products of cell Etching Solutions to Solar Cell makers and variety of high-efficiency phosphors for LED applications. These investment portfolio is well in line with future business environment driving for eco-friendly, thin, fast, low power consumption."

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.257-263
• /
• 2013

In this paper, Solar, Wind, fuel cell used in a Power conversion devices and industrial inverter motor to increase the efficiency of energy consumption, which is a core part of high-efficiency, high-voltage Trench Gate Field Stop IGBT was studied. For this purpose Planar type NPT IGBT and Planar type Field Stop IGBT have designed a basic structure designed to Trench Gate Field Stop IGBT based on the completed structure by analyzing the energy consumption of electrical characteristics, efficiency is a key part, high-efficiency and high-voltage inverter for industry regarding the optimization design for Trench Gate Field Stop IGBT.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.3
• /
• pp.141-146
• /
• 2016

The AMR(automatic meter reading) system has been increasingly and widely used for its efficient and intelligent management, which is a technology that automatically collects consumption data from a water meter or energy metering device. The digital meter instead of the mechanical meter should be used in the system. Up to now, various types of sensor to measure the water flow rate have been used in the digital water meter, for example, reed switch, photo IR approximate sensor, ultrasonic sensor, electromagnetic sensor, etc. In this paper, a new sensing technology, where a variable capacitor and digital circuit were used for sensing the water flow rate, was proposed. The circuit was designed and verified by Pspice simulation. And a PCB board for the circuit was fabricated. After then, a prototype of digital water meter using a variable capacitor to measure the water flow rate was fabricated. The function tests of the fabricated digital water meter were performed, and it was found that the meter worked properly. Since the new technology has much better properties in terms of cost and power consumption compared to conventional technologies, it should be one of the major digital water meter technologies in the future.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.5
• /
• pp.474-481
• /
• 2023

This paper is an experimental study on the optimal operating conditions of direct charging type electrospray for particulate matter collection. To perform the research, a direct charging type electrospray visualization system was configured to photograph the spray shape of microdroplets, and experiments were performed with varying electrode distance, flow rate, and applied voltage, which are the main factors affecting the particulate matter collection efficacy. Through image processing, the total number of microdroplets according to each condition was analyzed, and the number of microdroplets with a diameter of 1.5 mm or less was confirmed. In addition, by calculating the number of microdroplets per power consumption according to the applied voltage, the optimal operating conditions were derived in terms of energy consumption efficacy, and the microdroplet size distribution was analyzed under the optimal operating conditions. As a result of the experiment, it was confirmed that the optimal operating condition was at a flow rate of 10 mL/min and a voltage of -20 kV in case of 5 mm electrode distance, and at a flow rate of 15 mL/min and a voltage of -30 kV in case of 100 mm electrode distance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.8A
• /
• pp.752-759
• /
• 2010

The low power consumption is the most important design factor for the In-Body communication system of WBAN. The conventional PSSK (Phase-Silence-Shift-keying) modulation technique can be regarded as an extension from PSK modulation. And this PSSK has better power efficiency than PSK modulation, and higher spectral efficiency than FSK modulation. PSSK modulation is to transmit two orthogonal symbols. The transmission power can be lowered because the symbol rate in signal period becomes half. BER performance is improved because transmission power is lower and the modulation symbol distance is widened. In addition, PSSK preserve the low-power and increase the data rate than FSK. In this paper, we analyzed existing PSSK and like to propose a new PSPM (Phase-Shift-Position-Modulation) modulation scheme. This PSPM is evaluated in terms of considered bandwidth efficiency and BER performance, compared with the PSSK. This PSPM modulation method transmits the information data by both PSK symbol data and symbol position data, so that we can significantly improve the power efficiency. New proposed PSPM method could be very useful for the In-body communication that requires the most power efficient system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.7-7
• /
• 2010

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for Ubiquitous Sensor Networks(USN). In particular, the piezoelectric energy harvesting from ambient vibration sources has intensively researched because it has a relatively high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system has some drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure as shown in the figure. The natural frequency of a cantilever could be decreased to the usable frequency region (under 300 Hz) because the natural frequency depends on the length of a cantilever. In this study, the natural frequency of the energy harvester was a lower than a normal cantilever structure and sufficiently controllable in 50 - 200 Hz frequency region as adjusting weight of a proof mass. Moreover, the MEMS energy harvester had a high energy conversion efficiency using a shear mode ($d_{15}$) is much larger than a 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate for a standalone power generator for USN.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.1
• /
• pp.18-24
• /
• 2007

The continuously variable transmission (CVT) of which speed ratio can change continuously in a fixed range has the benefits of low fuel consumption and exhaust gas because it enables the engine of a vehicle to operate in a high efficiency range regardless of vehicle speed. The speed ratio of belt type CVT is controlled by adjusting line pressure. The one of the line pressure control methods, mechanical-hydraulic control is usually adopting VDT's control method, in which the secondary solenoid valve has two functions both a regulator and a line pressure controller. However, this control method could not show the high performance of CVT with optimal driving capability because of the limitation of simple control algorithm, and it could not gain market share sufficiently in spite of the advantage of CVT with low fuel consumption. On the other hand, the electro-hydraulic control method gives the enhancement of power performance and low fuel consumption by implementing various driving mode using the proportional control or PWM control. The key of CVT technique is to develop a control algorithm of the electro-hydraulic solenoid valve in order to implement the speed ratio efficiently. In this paper, the line pressure control algorithm is proposed and the hydraulic system is controlled using metal belt type CVT test rig and the embedded ECU platform.