• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.25-32
• /
• 1996

This paper is concenred with a finite volume time domain (FVTD) method for the analyses of transmission efficiency of electromagnetic wave propagation in tunnels with bend and fold. This method is gased on the volume integratio sof the maxwell's equation with respected to arbitrary shaped small polyhedron cells. The advantages of the present mehtod are that the algorithm is very simple since the coordinate system is restricted only to the cartesian, and so the arbitrary shaped boundaries can easily be dealt with since the fields at every center point of the cells are assigned in an average fashion.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.451-461
• /
• 2001

We present a simple design method of velocity-matched traveling-wave (TW) electrode with periodic capacitive loads. Once matching impedance and optical phase velocity are defined, the width and separation of coplanarstrip (CPS) and the magnitude and period of capacitive load are determined analytically. Calculation results of velocity-matched TW electrodes on GaAs substrates show bandwidths of more than 100 GHz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.3
• /
• pp.233-238
• /
• 2010

In this paper, we have proposed discrete ray tracing method (DRTM) for numerical analysis of characteristics of electromagnetic propagation along 2D random rough surfaces. The point of the present method is to discretize not only rough surface but also ray tracing. The former helps saving computer memories and the latter does simplifying ray searching algorithm resulting in saving computation time. Numerical calculations are carried out for 2D random rough surfaces, and electric field distributions are shown to check the effectiveness of the proposed DRTM.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.8
• /
• pp.401-406
• /
• 2004

In this experimentation, we investigated the characteristics of electromagnetic wave absorption of ferroxplana powder and silicone rubber composite. Ferroxplana was prepared by flux method at low temperature. The crystallization, magnetic properties and particle morphology of the obtained ferroxplana powder were investigated by using XRD, VSM and SEM. The particle size of ferroxplana powder was 2∼4$\mu\textrm{m}$ at the ratio of R=26, The coercivity and saturation magnetization of ferroxplana powder increased slightly with increase of temperature, The magnetic loss was the main factor of electromagnetic wave absorption of ferroxplana powder and silicone rubber composite, The maximum reflection loss of composite was about -l5dB below 4GHz.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.854-857
• /
• 2018

It becomes important to analyze the effects of electromagnetic wave on human body, as various wireless equipments are widely used in daily life. SAR (specific absorption rate) is a parameter of the effects of electromagnetic wave on human body. However, it considers only human tissues, and it is difficult to evaluate the effects of electromagnetic wave when metal artifacts are inserted such as dental implants. This paper introduces a method to simulate SAR, and gets its simulated results. Simulated SAR of human head model with dental implants in 30 GHz 5th generation mobile communications (5G) frequency band is $2.50{\times}10^{-3}W/kg$ in maximum and $8.58{\times}10^{-7}W/kg$ in average. These values are absolutely below 1.6 W/kg Korean domestic SAR limit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.640-646
• /
• 2008

Design procedure of corrugated horn antenna for the mm-wave frequency range is presented, and hybrid condition in horn is calculated. In this paper, corrugate profiles of horn which satisfy both transition to balanced hybrid condition and fabrication possibility under the mm-wave short wavelength are obtained. Electromagnetic fields inside horn and corrugation are derived by the cylindrical mode theory. Propagation characteristics in the horn are calculated by the mode impedance matching method with boundary conditions, and radiation fields are obtained by the Kirchhoff-Hyugen principle to the horn aperture fields. A mm-wave corrugated horn antenna which operates on $85{\sim}115GHz$ is fabricated by electric forming method. Measurements show that VSWR is under 1.3:1 over whole band and the half power beamwidth on radiation pattern 9.2, 9.16 and 9.02 degree on 85, 100 and 110 GHz are agree well with theoretical calculation.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.140-145
• /
• 2005

In this paper, an experimental investigation for return loss and a software-based prediction for interference level of single-packaged filtering antenna composed of dielectric waveguide filter and PCB(Printed Circuit Board) slot antenna in transceiver module have been carried out with several different feeding structures in millimeter-wave regime. The implementation and embedding method of the existing air-filled waveguide filters working at millimeter-wave frequency on general PCB substrate have been described. In a view of the implementation of each components, the dielectric waveguide embedded in PCB and LTCC(Low Temparature Co-fired Ceramic) substrates has employed the via fences as a replacement with side walls and common ground plane to prevent energy leakage. The characteristics of several prototypes of filtering antenna embedded in PCB substrate are considered by comparing the wideband and transmission characteristics as a function of bent angle of transmission line connecting two components. In addition, as an essential to the packaging of transceiver module working at millimeter-wave, miniaturization technology maintaining the performances of independent components and the important problems caused by integrating and connecting the different components in different layers are described in this paper.

• Journal of electromagnetic engineering and science
• /
• v.10 no.2
• /
• pp.61-66
• /
• 2010

This paper is concerned with an analysis of the back scattering of electromagnetic waves from a target moving along random rough surfaces such as the desert, and sea. First, the discrete ray tracing method(DRTM) is introduced, and then, this method is applied to the back scattering problem in order to investigate the effect of the back scattering from random rough surfaces on the electric field intensities. Finally, numerical examples of various height deviations of the Gaussian type of rough surfaces are shown. It is numerically demonstrated that the back scattering is dominated by the diffractions related to the reflections from the random rough surfaces.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.571-576
• /
• 1999

This paper describes both electromagnetic properties and electromagnetic-wave absorbind (EMA) characteristics of the radar absorbing coating materials in the microwave frequencies. The coating materials are prepared by mixing ferrite powder with epoxy resin polymers. The electromagnetic property and the EMA characteristics of the coating materials are measured in the frequency ranges between 0.2 GHz and 15GHz using the S-parameter method. The results show that the typical coating material has ({{{{ {μ }`_{r } ^{' } }} of about 2 and ({{{{ { ε}`_{r } ^{' } }} of about 4. And the coating materials have a little EMA characteristics in the frequency from 4 to 6 GHz and more improved EMA characteristics around 12 GHz And it is desirable for improvement of the EMA characteristics of the coating materials to properly select electromagnetic properties of constitutional materials inthe interesting frequency ranges.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.255-257
• /
• 2004

This paper was studied electromagnetic field distribution and damping of PD(Partial Discharge) signal in GIS(Gas Insulated Switchgear). Cut-off frequency of electromagnetic wave propagation modes were computed, electromagnetic field distribution of propagation modes in GIS by FEM(Finite Element Method) were simulated and simulated damping characteristic of electromagnetic waves in GIS by EMTP(Electromagnetic Transient Program) when generated PD pulse. Frequency band of $TE_{mn}/TM_{mn}$ modes were determinated by simulation results of electromagnetic field distribution and were discussed optimal position of UHF sensor from this results. Equivalent circuit was used to simulate signal damping of PD pulse in GIS by EMTP and compared with measured results in laboratory of KERI.