• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.1
• /
• pp.44-49
• /
• 2018

This study analyzed the Vulnerability of Network Communication devices when IEMI is coupled with the Network System. An Ultra Wide Band Generator (180 kV, 700 MHz) was used as the IEMI source. The EUTs are the Switch Hub and Workstation, which are used to configure the network system. The network system was monitored through the LAN system configuration, to confirm a malfunction of the network device. The results of the experiment indicate that a malfunction of the network occurs as the electric field increases. The data loss rate increases proportionally with increasing radiating time. In the case of the Switch Hub, the threshold electric field value was 10 kV/m for all conditions used in this experiment. The threshold point causing malfunction was influenced only by the electric field value. The correlation between the threshold point and pulse repetition rate was not found. However, in case of the Workstation, it was found that as the pulse repetition rate increases, the equipment responds weakly and the threshold value decreases. To verify the electrical coupling of the EUT by IEMI, current sensors were used to measure the PCB line inside the EUT and network line coupling current. As a result of the measurement, it can be inferred that when the coupling current due to IEMI exceeds the threshold value, it flows through the internal equipment line, causing a malfunction and subsequent failure. The results of this study can be applied to basic data for equipment protection, and effect analysis of intentional electromagnetic interference.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.113-116
• /
• 2000

평행평판의 원면에 위치한 슬릿을 통하여, 슬릿의 바로 윗 부분에 도체 스트립이 있을 때 일어나는 전자기적 결합 현상에 대하여 살펴보았다. 슬릿의 폭이 파장에 비하여 매우 작을 때와 매우 클 때의 두 경우로 나누어서 기술하였다. 슬릿의 폭이 좁은 경우는 기존의 개구결합(aperture-coupled) 마이크로스트립 안테나에 해당되며 슬릿의 폭이 넓은 경우는 기존의 proximity-coupled 마이르로스트립 안테나에 해당된다. 본 연구의 결과는 기존의 마이크로스트립 안테나의 급전구조와 기존의 마이크로스트립 누설파 안테나의 급전구조 설계에 도움을 줄 것으로 생각된다.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.39-43
• /
• 2002

In this thesis, a λ/4 hair-pin resonator is proposed to reduce the size of resonators. A LTCC MLC bandpass filter is designed using the λ/4 hair-pin resonators. The electromagnetic coupling structure between two planar resonators is analysed. The equivalent circuit is derived to explain the behavior of the LTCC MLC bandpass filter using λ/4 hair-pin resonators. A design procedure is also described. The simulated and measured results of 2-pole bandpass filter are presented.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.127-131
• /
• 2001

본 논문에서는 공진 주파수가 2 GHz 이며 크기가 작고, 광대역 특성을 갖는 Taper 형태의 급전선로를 갖는 마이크로스트립 Bow-tie 슬롯 안테나를 제안하였다. 이 구조에서는 대역폭을 향상시키기 위하여 마이크로스트립 슬롯 안테나 방사 슬롯을 변형된 bow-tie 모양으로 설계하여 기존의 Bow-tie 슬롯 안테나와 다른 구조를 제안하였고 Electromagnetic coupling를 좋게 하기 위하여 급전선로에 Taper를 첨가하여 급전기와 안테나의 정합을 이루어 광대역 특성을 갖도록 하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.11
• /
• pp.902-915
• /
• 2017

In recent years, mobile devices have become increasingly multi-functional and high performance, resulting in a dramatical increase in processing speed. On the other hand, the size of device is reduced, circuits inside the device are more easily exposed to electromagnetic interference radiated from antenna or adjacent circuits, degrading the system performance. To prevent this, it is necessary to design the device considering the electromagnetic characteristics with EM simulation at the design stage of product. However, the EM simulation takes a long analysis time and require high-level system resources for fast analysis. In this paper, an equivalent circuit modeling method for a round wire is proposed using a PEEC method and the electromagnetic coupling from a dipole antenna to a transmission line is analyzed in frequency domain. And compared with the result of electromagnetic simulator. As a result, PEEC method shows good agreement with those of electromagnetic simulation, in a much more short time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.8 s.99
• /
• pp.803-809
• /
• 2005

This paper presents a novel method of mutual coupling suppression between antenna elements for performance improvement in planar array antenna system. Two miniature patch antenna elements satisfied IEEE 802.1 la($5.75\~5.35\;GHz,\;5.75\~5.85\;GHz$) are used for this research, they are arrayed by half wave length interval. It is observed about -20 dB mutual coupling between each antenna element at center frequency. To suppress mutual coupling, the arrayed antennas with a reversed 'U' structure are observed below -30 dB mutual coupling at IEEE 802.1la band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.598-605
• /
• 2012

In this paper, a multi-layer dual-band bandpass filter using aperture-coupling is proposed. Two coupling paths are formed with the two apertures which exist between two dual-mode resonators. The coupling coefficients can be adjusted without changing the shape of resonators. The bandwidth of the second passband can be adjusted without affecting the bandwidth of the first passband using the size of an aperture between stubs of the dual-mode resonator. The aperture coupling mechanism is theoretically analysed. The dual-mode bandpass filter for the 2.4 GHz WLAN, 3.5 GHz WiMax was designed and fabricated. The fabricated filter shows centered 2.45 GHz and 3.5 GHz with 9 % and 8 % of the bandwidth.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.987-993
• /
• 2015

Wireless power transfer technologies typically include inductive coupling, magnetic resonance, and capacitive coupling methods. Among these methods, capacitive coupling wireless power transfer (CCWPT) has been studied to overcome the drawbacks of other approaches. CCWPT has many advantages such as having a simple structure, low standing power loss, reduced electromagnetic interference (EMI) and the ability to transfer power through metal barriers. In this paper, the CCWPT system with 6.78MHz class D inverter is proposed and analyzed. The proposed system consists of a 6.78MHz class D inverter with a LC low pass filter, capacitor between a transmitter and a receiver, and impedance transformers. The system is verified with a prototype for charging mobile devices.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.351-356
• /
• 2009

A dual-mode annular ring antenna for both global positioning system(GPS) and satellite digital multimedia broad-casting(DMB) is designed. The proposed antenna consists of a coupling feed line and four slots on the annular ring patch. The gap between the feed line and the annular ring patch is used for an input impedance matching, and the slot length is used for adjusting the resonant frequency of the $TM_{21}$ mode at the DMB frequency. The antenna was fabricated and measured. The experimental results show that the antenna resonants at the GPS and DMB frequencies with suitable bandwidths, and had a broadside radiation pattern at the GPS band and a conical beam radiation pattern at the DMB band.

• Journal of electromagnetic engineering and science
• /
• v.12 no.4
• /
• pp.254-259
• /
• 2012

This paper presents a closely spaced two-element folded-dipole-driven quasi-Yagi array with low mutual coupling between adjacent elements. The antenna utilizes a T-junction power divider as the feeding network, with an input impedance of $50{\Omega}$. A microstrip-stub is added to the ground plane in the middle of the two elements to improve the mutual coupling characteristics. The folded dipole driver is connected to a $50{\Omega}$ microstrip line via a broadband microstrip-to-coplanar stripline transition with a quarter radial stub. A mutual coupling of less than -22 dB is measured between two folded-dipole-driven quasi-Yagi antennas with a center-to-center spacing of 30 mm ($0.55{\lambda}_0$ at 5.5 GHz). The proposed quasi-Yagi array yields a measured bandwidth of 4.75~6.43 GHz for the -10 dB reflection coefficient and a gain of 6.14~7.12 dBi within the bandwidth range.