• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.162-162
• /
• 2009

Optical bounce which occurs by over twist of the liquid crystal (LC) director has a problem of response time in fringe-field switching (FFS) modes. After removing the electric field, effective birefringence ($d{\Delta}n_{eff}$) at the edge of pixel electrode meets the $\lambda/2$ phase instantly, since tilt angle of LC directors at that position suddenly decreases compared to twist angle. In this paper, based on the careful analysis, origin of optical bounce has been explained.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.63-64
• /
• 2009

Optical bounce during switching in the fringe field switching (FFS) mode using a liquid crystal (LC) with positive dielectric anisotropy has been observed. According to the analysis, it occurs at two positions which are center and edge of the pixel electrode, which decreases decaying response time. The former is major and mainly associated with increase in twist angle instantaneously during switching off resulted from decrease in tilt angle near by LC molecules at center. This paper discusses the origin of such optical bounces.

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.75-82
• /
• 2004

We have studied the influence of rubbing directions on electro-optic characteristics of the fringe field driven hybrid aligned nematic liquid crystal (LC) cell by computer simulation. When a LC with positive dielectric anisotropy is used, the results show that the driving voltage and transmittance decreases as the rubbing direction with respect to horizontal electric field direction increases. The reason for decrease in light transmission is the increase of tilt angle on the center of common electrode. In this paper, we have studied how the rubbing angle effects on the transmittance of the cell by investigating a distribution of electric field and LC director.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.957-960
• /
• 2003

We have studied the influence of rubbing directions on electro-optic characteristics of the fringe field driven hybrid aligned nematic liquid crystal (LC) cell by computer simulation. When a LC with positive dielectric anisotropy is used, the results show that the driving voltage and transmittance decreases as the rubbing direction with respect to horizontal electric field direction increases. The reason for decrease in light transmission is the reduction of twist angle and increase of tilt angle on the center of common electrode. In this paper, we have studied how the rubbing angle effects on the transmittance of the cell by investigating a distribution of electric field and LC director.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.314.1-314.1
• /
• 2014

The properties of Ni/Au Ohmic contacts formed on nonpolar a-plane GaN grown on r-plane sapphire substrate with different tilt angles are investigated using current-voltage (I-V) measurements. To investigate the effects of pattern direction and size on Ohmic contact properties of a-plane GaN, transmission line method (TLM) patterns are formed either along c-axis and m-axis on nonpolar GaN surface with different size. I-V measurement results show that the size of TLM pattern and formation direction of electrode have an effect on the electrical properties of a-plane GaN. The large sized patterns show the relatively lower sheet resistance compared to the small sized patterns. In addition, the sheet resistance of a-plane GaN along m-axis shows lower values than that along the c-axis. Finally, the effects of miscut angle of r-sapphire substrate ($0.2^{\circ}$, 0.4oand $0.6^{\circ}$) on electrical properties of a-plane GaN will be discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.398-398
• /
• 2007

The Liquid Crystal (LC) alignment uniformity is very important in LC devices. The alignment mechanism of LC molecules on a rubbed polyimide (PI) surface is very important for both LC fundamental research and application. So, Generally a rubbing method to align LC has been widely used to mass-produce LCD panels. But because rubbing method is contact method between rubbing fabric and indium-tin-oxide glass or flexible substrate, rubbing method has some defects, such as the electrode charges and the creation of contaminating particles. Thus we strongly recommend a non-contact alignment technique for getting rid of some defects of rubbing method. Most recently, the LC aligning capabilities achieved by ion-beam exposure on the organic and nonorganic thin film surface have been reported successfully. In this research, we studied the tilt angle generation and electro-optical performances for a NLC on homeotropic polyimide surfaces with ion-beam exposure. The LC aligning capabilities of a nematic liquid crystal (NLC) on a homeotropic PI surface using a new ion-beam method were studied. On the homeotropic PI surface, the tilt angle of the NLC by exposure ion-beam had a tendency to decrease as increased ion-beam energy density. And, on the homeotropic PI surface, the alignment character of the NLC with respect to ion-beam energy was good. And we achieved satisfactory result for EO character.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1054-1057
• /
• 2003

We have studied $90^{\circ}$ twisted nematic (TN) mode driven by fringe electric field, where two polarizers are parallel each other such that the cell shows a black state before a voltage is applied. According to the studies by computer simulation for a LC with negative dielectric anisotropy, the LC twists perpendicular to the horizontal field direction of fringe electric field and the degree of tilt angle is very low, when a voltage is applied. Therefore, the new device exhibits wide viewing angle characteristic due to in-plane switching and high transmittance since the LC director aligns parallel to the polarizer axis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.172-172
• /
• 2010

The Patterned vertical alignment (PVA) mode has many advantages such as perfect dark state at the normal direction and wide viewing angle. However, PVA mode needs additional process to pattern electrodes of both substrates and complicated assembly process. Moreover, this mode shows slow response time. To overcome these problems, we use plane shape ITO on top substrate instead of patterned electrode and form proper tilt angle of LC director on the surface while maintaining these original merits. Consequently, we achieve fast response time and improve transmittance.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.140-148
• /
• 2000

In this paper, using surface micromachining technology with thick photoresist and aluminum, an SLM(Spatial Light Modulator), which is applied to the fields of adaptive optics and pattern recognition system, was fabricated and the electromechanical properties of the fabricated micro SLM are measured. In order to maximize fill-factor and remove mechanical coupling between micro SLM actuators, the micro SLM is composed of three aluminum layers so that spring structure and upper electrode are placed beneath the mirror plate, and $10\times10$ each mirror plate is individually actuated. Also, the micro SLM was designed to be able to modulate phase and amplitude of incoming light in order to have a continuity of phase modulation of incoming light. In the case of amplitude and phase modulation, maximum vertical displacement is 4$\mum$, and maximum angular displacement is $\pm4.6^{\corc}$ respectively. The height difference of the fabricated mirror plate was able to be reduced to 1100A with mirror plate planarization method using negative photoresist(AZ5214). The electromechanical properties of the fabricated micro SLM were measured with the optical measurement system using He-Ne laser and PSD(position sensitive device).