• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.167-172
• /
• 2012

In this paper, we analyze the antenna performance variation by the ferrite absorbers which are widely used to optimize the antenna performance in near-field communications(NFC). Using various commercial absorbers, it was confirmed that the absorbers affect the electric performance of NFC antenna, and how to experimentally analyze the electrical influence of the absorbers in NFC antennas is proposed.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.587-594
• /
• 2010

The paper reports about methodology at design of interactive e-learning modules that are suitable both for teaching and learning. They cover special topics of electrical engineering, starting from the fundamentals, through electrical machines, power electronics to the fields of controlled electromechanical energy conversion, like electrical drives, complex drive systems, application of drives, mechatronic systems, telemanipulation, and robotics. In the paper, the emphasis is devoted in detail to philosophy and realization of the modules from fields of Power Electronics and Electrical Drives. On several examples there are explained main principles and specialties at their development.

• Journal of IKEEE
• /
• v.7 no.2 s.13
• /
• pp.218-222
• /
• 2003

Even if using the standard field test which radiation of electric wave and measurement test equipment there are difficult thing that building test equipment. so, we can use the substitution test field. In this paper, for optimization analysis for homogeneous field structure of GTEM-CELL (Giga hertz Transverse Electro Magnetic Cell) that calculate electromagnetic field characteristic for variable of each structure and characteristic impedance inner conductor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1162-1165
• /
• 2006

In this paper, the characteristics of polycrystalline silicon thin-film transistors (poly- Si TFTs) fabricated on polymer substrates are investigated. The a-Si films was laser annealed by using a XeCl excimer laser and a four-mask-processed poly-Si TFT was fabricated with fully self-aligned top gate structure. The fabricated nMOS TFT showed field-effect mobility of ${\sim}30\;cm^2/Vs$, on/off ratio of $10^5$ and threshold voltage of 5 V.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.215-222
• /
• 2013

Electrical power distribution systems are critical links between the utility and customer. In general, power distribution systems have unbalanced feeders due to the unbalanced loading. The devices that dependent on balanced three phase supply are affected by the unbalanced feeders. This necessitates the balancing of feeders. The main objective of reconfiguration is to balance the loads among the phases subject to constraints such as load flow equations, capacity and voltage constraints and to reduce the real power loss, while subject to a radial network structure in which all loads must be energized. Therefore, the distribution system reconfiguration problem has been viewed as multi-objective problem. In this paper, the hybrid heuristic algorithm has been used for reconfiguration, which is the combination of fuzzy and greedy algorithms. The purpose of the introduction of greedy is to refrain the searching for the period of phase balancing. The incorporation of fuzzy helps to take up more objectives amid phase balancing in the searching. The effectiveness of the proposed method is demonstrated through modified IEEE 33 bus and modified IEEE 125 bus radial distribution system.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1763-1768
• /
• 2016

This paper presents the electrical characteristics of the gallium nitride (GaN) current aperture vertical electron transistor (CAVET) by using two-dimensional (2-D) technology computer-aided design (TCAD) simulations. The CAVETs are considered as the alternative device due to their high breakdown voltage and high integration density in the high-power applications. The optimized design for the CAVET focused on the electrical performances according to the different gate-source length ($L_{GS}$) and aperture length ($L_{AP}$). We analyze DC and RF parameters inducing on-state current ($I_{on}$), threshold voltage ($V_t$), breakdown voltage ($V_B$), transconductance ($g_m$), gate capacitance ($C_{gg}$), cut-off frequency ($f_T$), and maximum oscillation frequency ($f_{max}$).

• Journal of IKEEE
• /
• v.19 no.2
• /
• pp.265-270
• /
• 2015

In this paper, we proposed a dual-directional SCR (silicon-controlled rectifier) based ESD (electrostatic discharge) protection circuit. In comparison with conventional SCR, this ESD protection circuit can provide an effective protection against ESD pulses in the two opposite directions, so the ESD protection circuit can be discharged in two opposite direction. The proposed circuit has a higher holding voltage characteristic than conventional SCR. These characteristic enable to have latch-up immunity under normal operating conditions as well as superior full chip ESD protection. it was analyzed to figure out electrical characteristics in term of individual design parameters. They are investigated by using the Synopsys TCAD simulator. In the simulation results, it has trigger voltage of 6.5V and holding voltage increased with different design parameters. The holding voltage of the proposed circuit changes from 2.1V to 6.3V and the proposed circuit has symmetrical I-V characteristic for positive and negative ESD pulse.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.415-420
• /
• 2005

This paper presents the two lossless auxiliary inductors-assisted voltage source type half bridge (single ended push pull: SEPP) series resonant high frequency inverter for induction heated king roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation for wide its output power regulation ranges and load variations under its constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operating principle is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation characteristics-based on the high frequency PDM strategy. The experimental operating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimental ones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliance implemented here is proved from the practical point of view.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.639-641
• /
• 2002

In this paper, we proposed the multiple access control of RS232C Serial Communications protocol using collision sense method. The communications wires of data transmission and reception are tied together through the buffer each to connect to the multiple communication channels. The hardware interface and control program are designed to build the prototype system and the experimental multiple access communications network is built by multiple PC systems and the transfer completion rate results are shown.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1600-1610
• /
• 2017

We propose maximum power extraction from a rooftop solar photovoltaic (PV) array during partial shading conditions. Partial shading is unavoidable during power extraction from rooftop PV systems due to nearby tall buildings (construction of additional floors) and trees (growth of trees). Many reconfiguration techniques can be used to extract maximum power in partial shading conditions, but in several cases, the real maximum power output is not achieved. In this study, a new switched PV technique is proposed to enhance the power output. The proposed technique is simple to use and more cost effective than other reconfiguration techniques. Therefore, it is suitable for rooftop applications. The power output of the proposed technique is compared with that of existing techniques with similar shading patterns. Eight panels with ratings of 250 watts (2 kW) each are used for testing. MATLAB simulation and hardware verification are done for the proposed and existing techniques. The proposed technique is implemented on a $4{\times}2$ PV array, although it can be extended to a number of arrays.