• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.249-251
• /
• 2001

This paper presents performance analysis on a low pass filter of a CT saturation detecting algorithm using difference. At the instants of beginning/end of saturation, the shapes of the secondary current are changed significantly though secondary currents are continuous. At the instants, the second-order or third-order difference of the secondary current has big values because of discontinuity of the first order difference. Thus, the third difference of the current is used to detect the beginning/end of CT saturation. An antialiasing low pass filter removes high frequency components and causes phase lag. A CT saturation detecting algorithm using difference of CT secondary currents is affected by the low pass filter. The algorithm is tested with cutoff frequencies of the filter for the two sampling rates of 64[S/C] and 32 [S/C]. The results of various test cases indicate satisfactory performance of the algorithm.

• Journal of the Korea Society for Simulation
• /
• v.10 no.4
• /
• pp.21-30
• /
• 2001

In this paper, EMI measurement, the STGU simulation being conducted, filter design, its characteristics, and its implementation to the PCB, and finally test results are discussed. When the low pass filter was implemented within the STGU, the power of EMI decreased more than 20dBm. Finally, when TE and MTIE, two important quality measure in synchronous reference clock, was assessed, ITU-T G813 requirement was satisfied. EMI(Electromagnetic Interface) is a measure of electomagnetic radiation from equipment in the range of 10KHz to 3GHz, and can cause unexpected reactions of electronics/electrical equipment. In this study, for safe and stable communication operation, a STGU (System Timing Generation Unit), which is a 2.5G SDH System and a major EMI source, was employed to simulate electromagnetic interface. Using Open-Site test, the power of fundamental frequency of EMI of interest and its harmonics were measured. Also, a low pass filter at cut-off frequency of 2GHz was specifically designed for this study to minimize the effect of EMI between electronic components.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1222-1227
• /
• 1990

The problem of identification of continuous systems is considered when both the discrete input and output measurements are contaminated by white noises. Using a predesigned digital low-pass filter, a discrete-time estimation model is constructed easily without direct approximations of system signal derivatives from sampled data. If the pass-band of the filter is designed so that it includes the main frequencies of both the system input and output signals in some range, the noise effects are sufficiently reduced, accurate estimates can be obtained by least squares(LS) algorithm in the presence of low measurement noises. Two classes of filters(infinite impulse response(IIR) filter and finite impulse response(FIR) filter) are employed. The former requires less computational burden and memory than the latter while the latter is suitable for the bias compensated least squares(BCLS) method, which compensates the bias of the LS estimate by the estimates of the input-output noise variances and thus yields unbiased estimates in the presence of high noises.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.2
• /
• pp.383-388
• /
• 2007

This paper considers a low-order dynamic output feedback controller design problem. Since the proposed control law inherently has a low-pass filter property, it can alleviate the mal-effects of the sensor noise without additional filter designs. Frequency domain analysis shows the characteristics of the proposed control law against measurement noise. The effectiveness of the proposed control law is illustrated by numerical simulations with a rotary inverted pendulum and a convey-crane. Using only one integrator the proposed control law has the advantage to the stabilization problem with sensor noise as well as it can successfully replace the measurements of derivative terms in a state feedback control law.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.5C no.4
• /
• pp.176-179
• /
• 2005

The increasing demand for high density packaging technologies and the evolution to mixed digital and analogue devices has been the con-set of increasing research in thin film multi-layer technologies such as the passive components integration technology. In this paper, Cu and TaO thin film with RF sputtering was deposited for spiral inductor and MOM capacitor on the $SiO_2$/Si(100) substrate. MOM capacitor and spiral inductor were fabricated for L-C band pass filter by sputtering and lift-off. We are analyzed and designed thin films L-C passive components for band pass filter at 900 MHz and 1.8 GHz, important devices for mobile communication system. Based on the high-Q values of passive components, MOM capacitor and spiral inductors for L-C band pass filter, a low insertion loss of L-C passive components can be realized with a minimized chip area. The insertion loss was 3 dB for a 1.8 GHz filter, and 5 dB for a 900 MHz filter. This paper also discusses a analysis and practical design to thin-film L-C band pass filter.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.850-853
• /
• 1987

A VLSI digital filter design using a semi-custom method is described. The digital filters composed of TDM/FDM Transmultiplexer are designed. Using the polyphase network approach a filter bank composed of only all-pass digital filter sections was designed. The use of all-pass filters as basic building blocks is shown to provide a transmultiplexer structure that has low computational requirements, low quantization noise, and high modularity. The silicon compiler systems is used to reduce the design time and increase the credibility of designed filters. A design of 1st order and 2nd order all pass filters is done using CMOS 2um N-well double metal cell.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.117-120
• /
• 2010

A novel stepped-patch loaded coplanar waveguide(SPLCPW) structure is proposed and applied to the design of a low-pass filter(LPF). The stepped-patch loaded on the opposite side of the CPW plane is shown to provide a shunt-connected series L-C resonance, which is dual to that of a conventional CPW defected ground structure(DGS). As a simple example of the proposed SPLCPW circuit, a 3-pole SPLCPW LPF is designed and good results are obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.191-194
• /
• 1999

Recently, with the rapid development and demand for compactness of portable communications, the requirement for compact and low-cost filter is increasing. One of the methods for reducing size and cost is to use high dielectric constant and low loss dielectric material in filter. The other is new monoblock dielectric band-pass filter (BPF) which has holes in a single dielectric body without additional coupling elements. This structure effectively reduces the size and cost of the filters. For previous conventional coaxial type dielectric BPF, dielectric substrates were used for coupling between adjacent resonators and additional input and output ports were needed. Coupling between adjacent resonators of monoblock BPF can be otained via electrode pairs. Capacitances of electrode pair structure for coupling are intensively investigated by 3-D FEM. The BPF for PCS has been designed to have a 30 MHz pass-bandwidth with center frequency of 1855 MHz and an attenuation pole at below the passband using a commercial 3-D structure simulator.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.10
• /
• pp.687-692
• /
• 1999

A new technique to measure low level capacitance variations of the gyroscope is proposed and verified by computer simulation. It is based on the new CV(capacitance-voltage) converter circuit biased by dc current source and the peak detector without low pass filter. The CV converter biased by dc current source provides good signal-to-noise ratio and this setup of the detection circuitry without low pass filter makes it possible to provide short settling time, that is, higher speed of measurement and wide operation range if only a few parameters are adjusted. The key parameters that affect the performance of the detection circuitry are illustrated and computer simulation results are presented. The demonstrated detection circuitry shows linear response from 10 fF to 130 fF at 10 kHz and shows good linearity.

• Journal of IKEEE
• /
• v.3 no.1 s.4
• /
• pp.11-21
• /
• 1999

This paper has been proposed a structure composed of FIRs and IIR filters as digital interpolation filter to integrate the off-chip analog low-pass filter of audio DAC. The passband ripple (>$0.41{\times}fs$), passband attenuation(>at$0.41{\times}fs$) and stopband attenuation(<$0.59{\times}fs$) of the ${\Delta}{\Sigma}$ modulator output using the proposed digital interpolation filter had ${\pm}0.001[dB]$, -0.0025[dB] and -75[dB], respectively. Also the inband group delay was 30.07/fs[s] and the error of group delay was 0.1672%. Also, the attenuation of stopband has been increased -20[dB] approximately at 65[kHz], out-of-band. Therefore the RC products of analog low-pass filter on chip have been decreased compared with the conventional digital interpolation filter structure.