• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.148-149
• /
• 2006

Capacitance-voltage(C-V) 측정평가를 통하여 ZnO/GaN 이종접합구조의 전기적인 특성을 조사한다. 실온에서 10kHz의 주파수에서 얻은 ZnO/GaN의 이종접합구조에 대한 C-V 측정결과는 이종접합계면에서 고밀도의 전자가 축적되어 있음을 나타낸다. 이것은 ZnO/GaN 이종접합계면의 다른 재료에서 볼 수 없는 큰 전도대불연속에 기인한 것인데, 각각의 층의 전도도을 제어함으로 이종접합계면에 축적되는 전자밀도를 ${\sim}10^{19}cm^{-3}$까지 증가시킬 수 있다. 따라서 ZnO/GaN 이종접합구조는 이종접합(合)트래지스터로서 유망한 재료로 판단된다.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.257-266
• /
• 2018

Here, a controlled green synthesis route involving hydrothermal pre-carbonization cum pyrolysis is reported that converts cucumber into graphene-like carbon nanosheets for supercapacitor application. Transmission electron microscopy analysis reveals the formation of ultra-thin carbon nanosheets with distributed pores. This cucumber derived carbon exhibits high specific capacitance of $143F\;g^{-1}$ in aqueous electrolyte. The two-electrode symmetric cell exhibits a specific capacitance of $58F\;g^{-1}$ at high current density, and high capacitance retention of 97% after 1000 cycles. This simple low-cost process involving widely available cucumber as biomass precursor is a promising, commercially viable approach for developing high-performance supercapacitors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.2
• /
• pp.232-238
• /
• 2013

In this paper we describe the maximum energy transfer of CSA(Capacitive Switching Antenna). CSA which is radiated antenna system contain energy storage and switch, antenna needs to high voltage source for electrical field radiation experiment. In this experiment we employed Marx generator as a charging source. CSA can radiate electrical field more efficiently by varying antenna capacitance. The electromagnetic generation system which was using CSA has some advantages which are more simple and more effective compared to exist system. We evaluated the performance of electromagnetic wave generating system using CSA. As a result UWB gain of system is 0.47, It is higher level than exist system is 0.3. Radiated electrical field strength at 1m is 70kV/m. It is measured by D-dot sensor and gap distance is 20mm. Center frequency of CSA is approximately 25MHz. When vary the antenna gap distance from 50mm to 20mm, we can find the radiation field strength is decrease and antenna center frequency is increased. We also simulated the energy transfer efficiency to compare with experiment result. Consequentially, CSA needs to appropriate capacitance which is similar value from marx generator for maximum energy transfer, and gap is less than 1mm to increase the CSA capacitance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.6
• /
• pp.514-524
• /
• 2016

This work suggests a study on 5 kW plasma power supply design and reactor capacitance estimation algorithm for a wide range of linear output control to operate a plasma reactor. The suggested study is designed to use a two-stage circuit and control the full-bridge circuit of the two-stage circuit using the buck converter output voltage of the single-stage circuit. The switching frequency of the full-bridge circuit is designed to operate through high-frequency switching and obtain maximum output using LC parallel resonance. Soft switching technique(ZVS) is used to reduce the loss caused by high-frequency switching, and duty control of the buck converter is applied to control a wide range of linear output. The internal capacitance of the reactor cannot easily be extracted, and thus, the reactor cannot be operated in an optimized resonant state. To address this issue, this work designs the internal capacitance of the reactor such that estimations can be performed with the developed reactor capacitance estimation algorithm applied to the internal capacitance of the reactor. A 5 kW plasma power supply is designed for a wide range of linear output control, and the validity of the study on the reactor capacitance estimation algorithm is verified.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1931-1933
• /
• 1999

In this paper, the current and voltage properties on the gate oxide film due to the variation of thickness are studied. The specimen is used for n-ch power MOSFET. It is shows the leakage current and current density characteristics due to the applied electric field when the oxide thickness is each $600[\AA],\;800[\AA]$ and $1000[\AA]$, respectively. We known that the leakage current is a little higher when the voltage as reverse bias contrast with forward bias in poly gate is applied. In order to experiment for AC properties is measured for capacitance characteristics. It is confirmed that the value of input capacitance have been a lot of influenced on $SiO_2$ thickness contrast with the value of output capacitance.

• Korean Journal of Materials Research
• /
• v.31 no.3
• /
• pp.115-121
• /
• 2021

MnO2 can be potentially utilized as an electrode material for redox capacitors. The deposition of MnO2 with poor electrical conductivity onto porous carbons supplies them with additional conductive paths; as a result, the capacitance of the electrical double layer formed on the porous carbon surface can be utilized together with the redox capacitance of MnO2. However, the obtained composites are not generally suitable for industrial production because they require the use of expensive porous carbons and/or inefficient fabrication methods. Thus, to develop an effective preparation procedure of the composite, a suitable structure of porous carbons must be determined. In this study, MnO2/C composites have been prepared from activated carbon gels with various pore sizes, and their electrical properties are investigated via cyclic voltammetry. In particular, mesoporous carbons with a pore size of around 20 nm form a composite with a relatively low capacitance (98 F/g-composite) and poor rate performance despite the moderate redox capacitance obtained for MnO2 (313 F/g-MnO2). On the other hand, using macro-porous carbons with a pore size of around 60 nm increases the MnO2 redox capacitance (399 F/g-MnO2) as well as the capacitance and rate performance of the entire material (203 F/g-composite). The obtained results can be used in the industrial manufacturing of MnO2/C composites for supercapacitor electrodes from the commercially available porous carbons.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.968-969
• /
• 2015

This paper proposes a novel analysis method for calculating inverter DC bus capacitance and line reactor parameters. In the realization process, DC bus capacitance parameter, and ripple current, life of DC bus capacitor, interaction between DC bus capacitance can be calculated by using Newton-Raphson procedure. The design scheme of DC bus capacitor and line reactor, specific parameters such as capacitance, loss, ripple current, central average temperature, life, ripple current, loss, size, central temperature of the reactor were given. Simulation results show that this scheme can accurately calculate the DC bus capacitance and line reactor parameters. Compared with calculation result of references, cost and volume are half. The indicators meet the demand of practical engineering. It had affirmed precision of the analytical method and verified correctness and feasibility of this method.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.161-169
• /
• 2009

MLCC (Multi-layer Ceramic Capacitor) is the most important passive component in electronic devices such as HHP, PC and digital display. The development trend of MLCC is a miniaturization with increasing the capacitance. In this paper, a development history of the high capacitance MLCC in Korea was introduced, and the necessity of the finer $BaTiO_3$ was explained in the viewpoint of the issued electrical and dielectric properties of high capacitance MLCC. The bottleneck technologies to realize the high capacitance was shortly introduced, followed by the prediction of the development trend of MLCC in near future.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1227-1232
• /
• 2014

The purpose of this paper is to establish the optimum fabricating condition of specimens using silk screen printing, and to develop humidity sensor which has good humidity sensing properties. The specimens are fabricated under the condition of 90[wt%] $SnO_2$-10[wt%] $TiO_2$, and their microstructure, crystalline structure, humidity sensing properties are examined. From the microstructure analyses, porosity is best at 700[$^{\circ}C$]. From the crystalline structure analyses, intensity of peak becomes strong according to increasing heat treatment temperature. From the humidity sensing properties analyses, an overall results of capacitance changes, linearity and hysteresis for the specimens is best at 600[$^{\circ}C$] and 700[$^{\circ}C$]. Capacitance of specimens increases according to decreasing measurement frequency, and to increasing relative humidity.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1297-1299
• /
• 1998

LB layers of L-$\alpha$-DLPC deposited by LB method were deposited onto n-type silicon wafer as Z-type film. Films made up of 8, 16 layers of lipid with long alkyl chain and the thickness of monolayer and multilayers was determined by ellipsometry. It was deposited Ag and Al onto LB layers and silicon wafer for electrode and small electrode exhibit high capacitance and low leakage current. The C-V curves of the MLS capacitor shows very high saturation value of capacitance. And cross-sectional SEM image of MLS capacitor indicated the presence of pore with Al electrode and we found that the Ag is good for electrode metal.