• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.4
• /
• pp.735-741
• /
• 2009

This paper presents an algorithm for the permanent magnet shape optimization of a large scale BLDC(Brushless DC) motor to minimize the cogging torque. A response surface method (RSM) using multiquadric radial basis function is employed to interpolate the objective function in design parameter space. In order to get a reasonable response surface with relatively small number of sampling data points, additional sampling points are added on the basis of design sensitivity analysis computed by using FEM. The algorithm has 2 stages: the first stage is to determine the PM arc angle, and the 2nd stage is to optimize the magnet pole shape. The developed algorithm is applied to a 5MW BLDC motor to get a minimum cogging torque. After 3 iterations with 4 design parameters, the cogging torque is reduced to 13.2% of the initial one.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.5
• /
• pp.222-230
• /
• 2005

This paper deals with the reduction of cogging torque of a outer-rotor type BLDC motor mainly used for washing machines. The motor comprises permanent magnet outer-rotor and stator with coils and core. This structure inherently produces vibration and cogging torque because of uneven reluctance according to rotation of the rotor. Up to now, adopted a type of 24 magnet pole and 36 slot-stator. This generates high main torque but accompanies comparatively large cogging torque. This paper proposes a 32-pole 36-slot type motor which reduces cogging torque remarkably. The influence of cogging torque is varied according to pole-slot combinations. The characteristic of the motor was obtained by a two-dimensional finite element method coupled with a drive circuit. The performance of the proposed model is superior to that of the existing model because of the reduction of torque ripple and the improvement of back ernf wave form.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1708-1712
• /
• 2008

This paper describes a linear matrix inequality (LMI) approach to the design of robust low-order power system stabilizers (PSSs), which are used to damp out local-mode oscillations of synchronous generators. The performance of a PSS is expressed as the location of the closed-loop poles, and a single fixed-gain pole-placement controller is synthesized for a wide range of operating conditions. The synthesis results in simultaneous regional pole-placement stabilization. and is formulated as an LMI feasibility problem with a rank condition. A penalty method is applied to solve the rank-constrained LMI problem. Numerical experiments with a single-machine connected to an infinite bus system were performed to demonstrate the proposed method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.971-976
• /
• 2011

This paper proposes a test system for a valve and poles building blocks used for large scale inverters such as STATCOM, SSSC, UPFC and VSC HVDC. Power semiconductors in the valve are normally connected in series to withstand switching voltage much larger than the voltage rating of a single power semiconductor. Therefore, there is a need to verify if the dynamic voltage sharing during switching in a valve is satisfactory. In this paper, we propose a test system that provides the necessary test condition: voltage and current in the valve using resonant circuits. A test scheme for a single phase inverter consisting two poles is also proposed. The performance of the inverter pole has to be verified at the factory test, before the system is installed at the site to secure the reliability of the system. The proposed scheme makes it possible to confirm if the pole can withstand voltage and current switching condition and handle loss.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.10
• /
• pp.1796-1801
• /
• 2007

This paper presents electric potential rise on the surface of the earth due to ground currents. It is the aim of this paper to propose fundamental data relevant to the earth surface potentials depending on the soil structures. The earth potential rise, touch and step voltages in the immediate vicinity of the ground rod of a distribution pole were measured and analyzed. The results described in this paper are based on laboratory measurements which were intended to simulate conditions existing in actual installations. As a result, the earth surface potential rise, touch and step voltages strongly depend on the soil structure. The highest earth surface potential occurred in the vicinity of the top of ground rod. When the ground rod was installed in the distance range of $1{\sim}1.5\;m$ from distribution pole, the highest touch voltages appeared near the place of 1 m on the straight line connecting the distribution pole to ground rod.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.544-546
• /
• 2000

This paper presents a monitoring technique of pole transformers using AC bridge circuit. And to detect the capacitance in oil more effectively, this paper used AC bridge circuit. The sensor in oil which could be placed inside of the distribution transformer can measures the changes of capacitance in oil. And with the sensing of the upper part's capacitance, it is possible to determine the changes of the oil height. Establishment of the proposed system helps to build the confidence in monitoring of the pole transformers.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.737-741
• /
• 1994

We show an application of a genetic algorithm to, control systems including neural networks. Genetic algorithms are getting more popular nowadays because of their simplicity and robustness. Genetic algorithms are global search techniques for optimization and many other problems. A feed-forward neural network which is widely used in control applications usually learns by error back propagation algorithm(EBP). But, when there exist certain constraints, EBP can not be applied. We apply a modified genetic algorithm to such a case. We show simulation examples of two cart-pole nonlinear systems: single pole and double pole.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.7
• /
• pp.339-350
• /
• 2002

Pole arcs, turn-on angle, and turn-off angle are major design factors, which affects Switched Reluctance Motor's torque performance. If these design factors are considered independently, the enhancement of SRM performance is restricted. Therefore, we need to consider pole arcs, turn-on angle and turn-off angle at the same time, when we design SR. In this paper, we analyze how these factors affect to torque ripple and average torque by using dynamic Finite Element Method(FEM) with derive circuit and present the good design results according to the various speeds. Especially, we formulate turn-on and turn-off angle from a voltage equation and present effective design range.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.175-177
• /
• 2008

본 논문에서는 개정된 KS 기준을 만족하면서 새로이 인도 조명기구용 pole을 설치할 필요 없이 기존의 가로등 pole에 바로 적용할 수 있는 높이가 낮은 인도용 조명기구용 반사판의 설계를 실행하고 광학 성능 예측 프로그램을 사용하여 그 성능을 확인하였다. 또한 설계는 신광원에 관심이 집중되고 있는 현재 추세에 맞추어 콤팩트 메탈할라이드 램프를 적용하여 실행하고 조명기구 반사판의 소형화 및 고성능화를 이끌어 낼 수 있도록 하였다.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.300-305
• /
• 2004

In this paper, new design equations based on the pole-zero analysis for multi-layered interdigital stripline linear group delay bandpass filter with tap input ports are presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of $\pm$0.1nS for LTCC technology or multilayered PCB technology is designed. In the design process, it is not necessary to simulate the entire structure, as the simulation of half structures is sufficient. Good results can be attained after the optimizing process was performed three times using the proposed equations and a commercial EM simulator.