• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.2
• /
• pp.55-61
• /
• 2002

In this paper, 'lifetime-temperature rise model' based on the 'lifetime-resistance model' is theoretically Proposed, in order to find out the evaluation method of degradation and the residual lifetime by use of infrared image camera for electric connections/contacts. Two assumptions have been builded up for the 'lifetime-temperature rise model': one is associated with the linear relationship between the temperature ism ΔK and contact resistance, and the other the functional relationship between the temperature of electric connections/contacts and the operating time presenting in the 'lifetime-resistance model'. To prove the proposed model, experiments have been performed for various electric connections/contacts. From the experimental results, measured values were quite similar to the calculated values, which proved the above-mentioned two assumptions. Therefore, by use of 'lifetime-temperature rise model', it is possible to estimate the trend of degradation and the residual lifetime for electric connections/contacts through the temperature measurements .

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.293-297
• /
• 1998

The influence of ion implantation on surface properties of polymers was studied. We investigated microhardness, friction, wear and wettablility of polyimide. Energies of 50, 200keV were used with doses range from $1{\times}10^{13} to 1{\times}10^{16} [ions/cm^2]$. The implanted ion species were B, N and Ar. The microhardness of polyimide was increased after implantation for doses of $1{\times}10^{15}\; [ions/cm^2]$. A reduction of the friction coefficient was in most case correlated with a reduction of wear. The contact angles of water for $B^+,N^+$ implanted polyimide decreased from $76^{\circ}C$ to zero, as the fluencies increased at energies of 50 and 200 KeV. However, the contact angle of Ar ion implanted polyimide did not change under ambient room conditions even if the time elapsed. SEM measurement was performed to characterize the modified surface layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.57-60
• /
• 2000

In this paper, study on the properties of the thermal degradated epoxy resin which is used in indoor insulation apparatus is performed to investigate the problems of the decreasing insulation characteristics and crack in the indoor insulation apparatus. As a parameter of variation, SEM, contact angle, surface resistivity, relative dielectric constant and weight loss are measured. As the results of the above measurements, the contact angle and surface resistivity of the epoxy resin has increased to 200$^{\circ}C$ in but at the above 200$^{\circ}C$ the values have decreased. The relative dielectric constants the thermal treated samples have increased on with the temperature increase. We find the volatile components of the epoxy resin compound has disappeared during thermal degradation by SEM. The insulation properties of the epoxy resin have increased by the 200$^{\circ}C$ but decreased in the above 200$^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.205-205
• /
• 2007

The SiOC film of carbon centered system was prepared using bistrimethylsilylmethane and oxygen mixed precursor by the chemical vapor deposition. The chemical properties of the SiOC film were analyzed by the I-V measurement and FTIR spectra. The main bond of 950~1200 cm-1 was composed of the Si-C, Si-O-C and Si-O bonds. The leakage current of the SiOC film increased with the increasing of the carbon content, and the drift of the current was similar to the Si-O-C bond content.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.388-394
• /
• 2008

The purpose of this paper is concerned with a battery type powered handpiece drive system for surgical operation. Battery type powered surgical handpiece is suitable for delicate surgical operating. The conventional air-type handpiece has a mechanical noise, a strong oscillation and a danger of infection. And the conventional contact switching type handpiece has problems that is restricted by surroundings. By reason of this kind, we studied noncontact switching type surgical handpiece to change conventional air type surgical handpiece and contact switching type. Also in this paper we develop the battery type power handpiece drive system for surgical operation using controller IC UC3625 of UNITRODE CO. Finally some experimental and simulation results are provided to demonstrate the validity of the proposed battery type power handpiece drive system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.508-509
• /
• 2005

In case of ITO/MEH-PPV/Al structure, the quantity of charge carriers flowing through the organic material was few and the density of them is fixed. The electric field inside of the device almost didn't change with the position. On the other hands, in case of Au/MEH-PPV/Au structure, the hole density increased rapidly nearby the anode but decreased nearby the cathode. The space charge phenomenon followed sufficient hole injection resulted in the change of the electric field with the position inside of the device. We verified that the result of the current-voltage simulation corresponded with experimental result.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.305-307
• /
• 2005

In the cold and temperate regions of Korea the icing and ice coats on 25[kV] electric car line during winter is a very serious problem. This generates shocks at the mechanical interface of the collecting strips of the pantograph and the contact wire and extra electrical resistance, which may affect quality of current collection at the contact wire / collecting strips of pantograph interface. De-icing operations should be performed just before train operation to avoid the formation of another ice layer. This paper presents temperature analysis of the de-icing system which could be applied to the electric car line of railways.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.318-331
• /
• 2000

Electrical and tribological behaviours of a copper-graphite brush in a slipring-brush assembly were investigated to evaluate the characteristics of electric signal transmission between a slipring and a brush. Five brush materials containing different amounts of copper and graphite were studied. The result showed that a copper-graphite brush at a particular graphite content exhibited the most stable frictional and electrical behaviour suggesting an optimum amount of a solid lubricant in a metal-graphite brush system. Microscopic observation and the surface analysis showed good agreements with this phenomena. In addition, the deviation of the friction coefficient and electric signal distortion has a close relationship with a microscopic mechanical vibration and the change of a real contact area.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.1
• /
• pp.50-57
• /
• 1986

The fabricatoin sequence of GaAs MIS type diode and its electrical characteristics are presented. Used wafers were undoped GaAS wafer adn Te-doped GaAs wafer. Au and AuGe/Ni was used as schottky contact metal and ohmic contact metal respectively. Oxide layer on GaAs surface was formed by water vapor saturated oxide growth technique and dry oxidation technique. In Te-doped GaAs wafer, cutin voltage of MIS type diode was enhanced about 3V comparing with non-oxide layer diode. From light I-V characteristics fill factor of MIS type Te-doped GaAs diode was about 64%, Voc(open circuit voltage) was 0.67V.

• Journal of applied mathematics & informatics
• /
• v.41 no.3
• /
• pp.487-510
• /
• 2023

We propose a mathematical model which describes the frictional contact between a piezoelectric body and an electrically conductive foundation. The behavior of the material is described with a linearly electro-viscoelastic constitutive law with long term memory. The mechanical process is dynamic and the electrical conductivity coefficient depends on the total slip rate, the friction is modeled with Tresca's law which the friction bound depends on the total slip rate with taking into account the electrical conductivity of the foundation both. The main results of this paper concern the existence and uniqueness of the weak solution of the model; the proof is based on results for second order evolution variational inequalities with a time-dependent hemivariational inequality in Banach spaces.