• 대한의용생체공학회:의공학회지
• /
• 제17권3호
• /
• pp.373-378
• /
• 1996

In this paper, we calculated chronaxy value in order to determine the optimal conditions and stimulus pulse of information transmission. We also developed an electrical equivalent circuit of the hand including the contact part, which consists of two resistors (a contact resistor and finger resistor) and a capacitor. The minimum recoulition voltage was measured by using electrical stimulus. We found that the ranges of the above two resistances and the capacitance are 30-130k$\Omega$, 20-60k$\Omega$ and 10-30nF respectively. We found that the minimum recoulition voltage was the lowest at 100-300Hz and 10% of the duty ratio.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권4호
• /
• pp.153-160
• /
• 2001

In order to analyze the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to high temperature. Then, the degradation process was evaluated by comparing contact angle, surface potential, surface resistivity, and XPS. The experimental results showed that the amount of weight loss, contact angle, surface potential and surface resistivity increased up to 200 $^{\circ}C$ as a function of temperature. These phenomena show the existence of hydrophobic surface. With the change to the hydrophobic surface and the electrical potential and resistivity on FRP surface increased. In XPS to analyze surface chemical structures, the increased hydrophobicity in thermal increase of unsaturated double bond in carbon chains. Aslo, thermal treatment caused the discoloration on the point of treated surface. These phenomena were attributed to the generations of ether group.

• 한국세라믹학회지
• /
• 제54권3호
• /
• pp.249-256
• /
• 2017

We design Ge-Al multilayer assemblies as anode materials for Li-ion batteries, in which Ge and Al thin films are alternately deposited by a radio sputtering method. By sandwiching Ge layers between Al layer, the cyclability, rate capability, and capacity of Ge are improved significantly. The success of the Ge-Al multilayer is attributed to the Al films. To maintain the integrity of electrical contact, Al acts as an elastic layer, which can expand or shrink with the Ge film upon lithiation or delithiation. In addition, the presence of the Al film on the surface can prevent direct contact of Ge and electrolyte, thereby reducing the growth of a SEI layer. Importantly, with high electrical and ionic conductivities, the Al film provides efficient electrical and ionic routes for electrons and Li-ions to access the Ge film, promoting a high specific capacity and high rate capability for Ge.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.266-269
• /
• 2001

This paper investigated the aging characteristic under long-term corona discharge on loon temperature vulcanized silicone rubber, which has been using as a protective coating material for solving the contaminant problem. The applied electrical field is 10kV/cm ac and corona discharge treatment was applied on RTV silicone rubber sheet for maximum 250 hours. With the duration of corona discharge, the diffusible low molecular weight species increased, which was determined the usage of n-hexane extraction method. In addition, the contaminant layer was formed on the treated surface, and then measured the contact angle. We investigated the relation of contact angle and diffusible low molecular weight species. It is found that scissor of main chain PDMS and side chains (CH$_3$) and the generation of LMW species were occurred by a corona discharge. The improvement of hydrophobicity rate is thought due to the increase of diffusible LMW species.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.75-78
• /
• 2002

In this paper, we investigated the change of wettability, surface potential decay and surface resistivity caused by thermal-treated and plasma-treated FRP respectively for finding out the influence of electrical characteristics on the surface of polymer composites. For the change of wettability, the contact angle of thermal-treated specimen with the high temperature of 200$^{\circ}C$ increased. But that of plasma-treated specimen decreased. The characteristic of surface potential decay shows the tendency of the remarkable decrease on plasma-treated specimens, but no difference on thermal-treated specimen compared with untreated one. Also, for the surface resistivity, it shows the same trend compared with the change of contact angle. We can conclude that the degradation phenomena of epoxy surface are dominated by the induction of hydrophilicity and hydrophobicity.

• E2M - 전기 전자와 첨단 소재
• /
• 제3권4호
• /
• pp.325-331
• /
• 1990

본 연구는 텅스텐 소결에 저온 활성제로 작용하는 Ni-P 공정합금을 미량첨가하여 제조공정의 간단화를 통한 새로운 W-Cu계 전기접점제조를 목표로 하였다. 이를 위해 1회 용침공정을 통해 제조한 W(Ni-P)-Cu 합금에 대한 전기접점특성을 조사하여 접점의 미세구조 관점에서 논의하였다. Ni-P 합금첨가한 접점은 기존의 순수 W-Cu 합금에 비해 낮은 접촉저항 및 낮은 아크소모를 나타내는 우수한 접점성능을 보여주었다. 이것은 Ni-P합금이 Cu용침이 개시되기전 짧은 승온단계에서 분말간의 강한 결합과 Cu용침에 유리한 기공통로를 갖는 W 분말 골격체의 형성을 유도하기 때문인 것으로 판단된다.

• 전기학회논문지
• /
• 제66권2호
• /
• pp.468-473
• /
• 2017

This paper presents an in-process measurement system for shaft radius measurement during grinding process. This system does not require to stop the grinding process, which can enhance productivity and quality. In order to measure the radius, the system employs an eddy current sensor that can measure without any contact with the shaft. This type of sensor is very appropriate because it is insensitive to interference such as cutting fluid, coolant, contact pressure, and wear. For data analysis, the measurement system is modeled as a linearized discrete form where the states with noise are estimated by an extended Kalman filter. This system has been validated through simulations and experiments.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.203-206
• /
• 2017

The effect of the content of microsilica and nanosilica continuously modified with hydroxy silane and epoxy-modified silicone in cycloaliphatic epoxy/microsilica/nanosilica composites (EMNCs) on the mechanical and water repellent properties was evaluated. Surface-modified micro- and nanosilica was well-mixed with a cycloaliphatic epoxy resin in the presence of polyester-modified polydimethylsiloxane (PEM-PDMS) as a dispersing agent using an ultrasonicator. Tensile and flexural tests were carried out using a universal testing machine (UTM). The water repellent property was evaluated by contact angle measurements of water on the composite surface. Tensile strength of the composite could be enhanced by 32.2% up to 91.4 MPa, and the flexural strength was raised to 122.0 MPa, which is 38.8% higher than that of neat epoxy. The contact angle of water on the composite was as high as $104.1^{\circ}$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.501-502
• /
• 2006

In this paper, new and aging sample of MCCB and ELCB are investigated the main performance test such as short circuit test, mechanical and electrical endurance test, dielectric test and surge current test. The surface conditions of new and aging sample are analyzed by SEM, TGA and DSC. The ELCB occurred badness mainly in short circuit test and surge current test. The badness cause of short circuit test was confirmed due to imperfect contact of contact part.

• Structural Engineering and Mechanics
• /
• 제81권4호
• /
• pp.481-492
• /
• 2022

Cycloidal ball planetary transmission (CBPT) has many applications as precision reducer, such as precision machinery and automation drive systems etc. The traditional analytical model of CBPT cannot accurately describe the change of the normal force of meshing points, and thus cannot describe the precise transmission process of meshing pairs. In the paper, a method for deriving the normal force equation is put forward by using the non-linear relationship between force and deformation in elastic mechanics. The two-point contact analytical models of all the meshing pairs are established to obtain the micro-displacement analytical model of CBPT under axial pre-tightening. Then, the non-real-time two-point contact analytical models of all the meshing pairs are further constructed to obtain the normal force expression to determine the critical compression coefficients. Experimental investigations are performed to verify the analytical model using the critical compression coefficients.