• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.162-166
• /
• 2000

In this paper, we studied the relation between using amount of Ferrite and electromagnetic wave absorbing properties of ferrite-rubber composite. The variation of using amount of Ferrite have been 52 wt.% ~ 62 wt.%. As s result, it has been shown that the electromagnetic wave absorbing properties of ferrite-rubber composite are related to the using amount of Ferrite in composite. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the control of using amount of Ferrite.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.237-237
• /
• 2010

We investigated physical properties of CuIn1-xGaxSe2 thin films grown by co-evaporator under various Cu environments. To study the effect of the Cu environments on absorber layer properties, thin films were fabricated under various reaction periods for different Cu flux on 2 stage process. We find the structural and electrical characteristics were affected by the reaction period on 2 stage process. The correlation between Cu flux variation on 2 stage process and solar cell performance was studied. The structural and electrical properties for various Cu flux were discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.4
• /
• pp.453-459
• /
• 2004

In this experiment, flux method was applied for preparing ferroxplana at low temperature, The common salt was used as a flux. The mole ratio of flux to Zn$_2$Y was varied with 0, 6.5, 13, 26 and 52 in dry ball-mixing. Zn$_2$Y was obtained after heat treatment of the mixed powder. Crystallization, particle morphology and magnetic properties of the prepared powder were investigated using XRD, VSM and SEM. The ferroxplana powder of 2-4 ${\mu}{\textrm}{m}$ was obtained with the mole ratio 26 by heat treating at the temperature of 110$0^{\circ}C$. The coercivity(H$_{c}$) and saturation magnetization(M$_{s}$) of the ferroxplana were 282Oe and 64.5emu/g, respectively.y.y.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.2
• /
• pp.96-101
• /
• 1988

This work is concerned with the fabrication process and photo-response characteristics of Cd S/(p) Si solar cells. In order to fabricate the cell. low grade Si wafer has been used as an absorber and Cd S which works as a window material has been prepared by vacuum evaporation. Cd S thin film, as evaporated, is polycristal and resistance is very high but these properties are improved by annealing. The properties of the fabricated cells are found to depend largely on the transmittance of Cd S. The effects of Cd S thickness and annealing condition on the fill factor and efficiency of the cell are investigated quantitatively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.556-560
• /
• 1995

The absorption properties of Cu-Zn ferrite/rubber composite microwave absorbers with PZT(Lead Zirconate Titanate) additive were evaluated. The composite specimens have prepared by molding and curing the mixture of matrix rubber and Cu-Zn ferrite powders which are synthesized by the coprecipitation method using Fe Cl/sub 3/ .center dot. 6H/sub 2/O, CuCl/sub 2/ .center dot. 2H/sub 2/O and Zn Cl/sub 2/ as a starting raw materials. PZT is used as another filler particles to adjust the material constants of Cu-Zn ferrite/rubber composite specimens. We have found that the material constants of specimens could be controlled by various PZT mixing ratio. On the Cu-Zn ferrite/rubber composite specimens with PZT 10[wt%] additive, the reflection losses were larger than 30[dB] in the frequency range from 2.72 to 4.4[GHz]' by adjusing the thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.208-208
• /
• 2008

Micro patterning of conductor line/space on LTCC green sheet in the LTCC module is an important process for miniaturization in 3D integrated circuits. This work presented the effect of inorganic binders on the microstructure, adhesion, electrical resistivity, shrinkage and line/space resolution, which is a part of study in photoimageable conductor paste. The photoimageable conductor paste contains silver powder, polymer binder, monomer, photo-initiator, UV absorber, and solvent. The inorganic binders were furnished with varied weight percentage of anorthite, diopside and MLS-62 glass frits from 0% to 7%. The Line/space sizes thus obtained was under 25 micron.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.13-21
• /
• 2000

Au-black for the application of the long wavelength infrared absorber has been prepared by evaporating Au under nitrogen gas-filled low vacuum condition. Characteristics of the deposited Au-black were carefully investigated through structural analysis, infrared absorbance measurement, and patterning of the layer, all of which are dependent on the deposition condition. High density of micro-cavity that trapped infrared were obtained, and infrared absorbance in the wavelength range from 3 $\mu\textrm{g}$ to 14 $\mu\textrm{g}$ was found to be about 90% when the Au-black layer was produced under the deposition condition of mass Per area of about 600 $\mu\textrm{g}$/cm$^{2}$ and chamber pressure of above 1 Torr. Photoresist lift-off process could be performed to pattern the Au-black, of which mass per area was below 900 $\mu\textrm{g}$/cm/ sup 2/. In view of absorbance, heat capacity, and pattern formation, the deposition condition of chamber pressure of about 1 Tow and mass per area of about 600$\mu\textrm{g}$/cm$^{2}$ was most adequate for preparing the Au-black as an infrared absorber.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.52-59
• /
• 2014

The aims of this paper are to characterize the transient overvoltages(TOVs) and to evaluate the risk occurring at 22.9kV consumer's substation. The measurements of lightning- and switching-caused TOVs were made during Mar. 2013 and Feb. 2014. As a consequence, 47 events of TOVs were recorded and 4 of them were higher than the input voltage envelope(IVE) of the information technology industry council(ITI) curve. The measured TOVs are characterized by longer front times and longer durations compared to the $1.2/50{\mu}s$ standard impulse voltage waveform, and some of them represent bipolar waves with lower oscillation frequencies. It suggests that the test of non-standard impulse voltage waveforms is needed for effective risk assessments of power apparatus. Lightning- and switching-caused TOVs exceeding IVE of ITI curve are induced at the secondary of 22.9kV potential transformer(PT). We may, therefore, conclude that the surge protection devices should be applied at the secondary of PT and the surge absorbers should be installed at the primary of VCB or PT. The results presented in this paper could be useful to design the reasonable insulation coordination for 22.9kV consumer's substation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.675-675
• /
• 2013

CIGS thin films have received a great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films have been deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. In this study, Cu(In,Ga)Se2(CIGS) thin films were prepared using a single quaternary target by rf magnetron sputtering. The effect of sulfurization on the structural, compositional and electrical properties of the films was examined in order to develop the deposition process. An optimal sulfurization process will be selected for the preparation of CIGS thin films with good structural, optical and electrical properties by applying various sulfurization processes. In addition, the electrical properties of CIGS thin films were investigated by post-deposition annealing process. The carrier concentration of CIG(SSe) thin films after sulfurization was increased from $10^{14}cm^{-3}$ to $10^{16}cm^{-3}$ and the resistivity was increased from 10 ${\Omega}cm$ to $10^3$ ${\Omega}cm$. It is confirmed that CIG(SSe) thin films prepared at optimal deposition condition have similar atomic ratio to the target value after sulfurization.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.49-56
• /
• 2014

In this study, the generation efficiency of the limited area of a concentrator solar cell was increased by using a solar concentrator and a tracking device. Heat generated by the solar cell was collected using a thermal absorber for supplying hot water or heating. Thus, the concentrator solar cell system provided electricity and heat simultaneously. Tracking of the sun by detecting the sun's position, repositioning of heating device towards the east after sunset, and shutting down of system after sunset were successfully implemented using an illuminance sensor (CdS) and Simulink, a commercial software package. We performed parametric analysis of the velocity, fin installation, and entrance location with respect to the operating temperature of the concentrator solar cell. A heat transfer simulation model was developed for comparing the actual temperature profiles of the concentrator solar cell and thermal absorber, and good agreement was found between the results of the simulations and the experiments.