• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.5
• /
• pp.128-133
• /
• 2013

In this paper, octagonal inductors for RFIC designs was fabricated with 90nm CMOS Technology to compare its quality factor and the effective inductance as functions of radius and number of turn. The quality factor decreases as the inner radius and the number of metal turned increase. However, the effective inductance increases with the increasing the inner radius and the number of metal turned. Therefore, the inductor structure should be decided according to the relative importance of Q-factor and inductance.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.389-392
• /
• 1999

It is essential to estimate an effective inductance in a ground plane of muliti-layer IC package system in order to determine the simultaneous switching noise of the package. A new method to estimate the effective ground inductance in multi-layer IC package is presented. With the estimated ground plane inductance values, maximum switching noise variations according to the number of simultaneously switching drivers are investigated by developing a new SSN model. These results are verified by performing HSPICE simulation with the 0.35${\mu}{\textrm}{m}$ CMOS technology.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.7
• /
• pp.267-275
• /
• 1985

The finite element method for calculating single phase transformer inductance is presented in this paper. There are three basic definitions of saturated transormer inductance. The set of nonlinear finite element equations is solved by the Newton-Raphson method which assures nearly quadratic convergence of the iteration process. The effect of perturbation of currents of this transformer is used to calculate the saturated winding inductance. This approach is used to calculate the apparent, effective and incremental inductance of single phase transformer. The apparent inductance is in good agreement with resting result. The approach enabled one to study the variation of winding inductance according to the saturation levels in the core at any operating point.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.855-856
• /
• 2006

Inductance can be defined as several kinds of slops on the B-H curve, and at is classified into apparent, effective, incremental inductances, etc. In many research cases, its calculation and measurement are partially dealt. However it is hard to find the clear explanation of the inductance in the voltage equation of PM machines, and even its relationship with those classified inductances in the view point of design and characteristics analysis. Moreover some previous definition of inductance can not be used for the inductance of coils in PM machines. Therefore, in this paper the inductance is redefined for voltage equation of PM machines, and the methods of calculation by using finite element analysis method and measurement are explained.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.50 no.5
• /
• pp.605-615
• /
• 2017

A multi-resonant broadband acoustic transducer with six Tonpilz elements operating at different resonant frequencies in a transducer assembly was fabricated, tested, and analyzed. A compensated transducer, modified by adding series inductance to the developed multi-resonant broadband transducer, was shown to provide improved bandwidth performance with a relatively more uniform frequency response compared with the uncompensated transducer. By controlling the series inductance, flat frequency response characteristics at two frequency bands were obtained over the range 38-52 kHz with 1.1 mH inductance and 50-60 kHz with 0.4 mH inductance. These results suggest that the operating frequency of the developed multi-resonant broadband transducer in a chirp echo sounder can be shifted to a different frequency band that is optimized according to the environment for more effective echo surveys of fishing grounds.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.4
• /
• pp.367-371
• /
• 2003

In order to determine the effective way of measuring the Mode I stress intensity factor for a material containing a two-dimensional surface crack by means of the alternating current potential drop(ACPD) technique, the change in magnetic flux density between crack surfaces and above the specimen surface due to load was studied theoretically. The magnetic flux density in the air between crack surfaces is uniform and above the specimen surface is not changed by increasing the load in the material. Therefore, the change in potential drop due to load in a measuring system which was designed to induce a large amount of electro-motive force was caused by the change in internal inductance of material, the change in the mutual inductance between internal inductance of material and measuring system and the change in the mutual inductance between internal inductance of material and power supply line.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.8
• /
• pp.1180-1185
• /
• 2015

This paper describes the accurate inductance measurement of a switched reluctance motor (SRM). Conventionally, the inductance of the SRM is measured using the equivalent circuit of a stator phase or time constant of exponential current transient. This paper presents an effective method to measure the SRM inductance accurately and rapidly using automated voltage integration. The proposed method is validated experimentally by comparison with the existing equivalent circuit method (ECM) and the FEA(finite element analysis) simulation.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.1141-1144
• /
• 1998

A new design methodology for the shortchannel CMOS IC-package is presented. It is developed by representing the package inductance with an effective lumpedinductance. The worst case maximum-simultaneous-switching noise (SSN) and gate propagation delay due to the package are modeled in terms of driver geometry, the maximum number of simultaneous switching drivers, and the effective inductance. The SSN variations according to load capacitances are investigated with this model. The package design techniques based on the proposed guidelines are verified by performing HSPICE simulations with the $0.35\mu\textrm{m}$ CMOS model parameters.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.259-269
• /
• 2012

With the lower supply voltage and the higher operating frequency in integrated circuits, the analysis of the power distribution network (PDN) including on-chip inductances becomes more important. In this paper, an effective inductance extraction method for a regular on-chip power grid structure is proposed. The loop inductance model applicable to chip layout is proposed and the inductance extraction tool using the proposed inductance model based on post layout RC circuits is developed. The accuracy of the proposed loop model and the developed tool is verified by comparing the test circuit simulation results with those from the partial element equivalent circuit (PEEC) model. The voltage fluctuation from the RLC circuits extracted by the developed tool was examined for the analysis of on-chip inductance effects. The significance of on-chip power grid inductance was investigated by the co-simulation of chip-package-PCB.

• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.396-404
• /
• 2010

This paper presents simple schemes used to estimate the initial rotor position and the d- and q-axis inductances for effective Maximum Torque per Ampere (MTPA) operation in a wind-power system using an IPMSM (Interior Permanent Magnet Synchronous Machine). An IPMSM essentially requires an exact coordinate transformation and accurate inductance values to use a reluctance torque caused by the saliency characteristic. In the proposed high-frequency voltage testing method, there is no voltage drop caused by the resistance and the electromotive force. The initial rotor position and the inductance can be measured through an analysis of the stator current without turning the rotor. The experimental results are presented in order to illustrate the feasibility of the proposed method.