• 농업과학연구
• /
• 제6권2호
• /
• pp.185-191
• /
• 1979

시멘트의 응결(凝結) 경화촉진제(硬化促進劑)로 사용(使用)되는 염화(鹽化)칼슘 첨가량(添加量)이 mortar의 강도(强度)에 미치는 영향(影響)을 연구(硏究)하기 위하여, 보통 mortar를 경화(硬化)시킨 경우와 $CaCl_2$을 1.0%. 2.0%, 3.0% 첨가(添加)하여 경화(硬化)시킨 경우의 압축강도(壓縮强度)와 인장강도(引張强度)를 배합비별(配合比別), 재영별(材令別)로 구분(區分)하여 비교시험(比較試驗)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 압축강도(壓縮强度)는 염화(鹽化)칼슘을 첨가(添加)한 몰타르가 보통(普通) 몰타르보다 크게 나타났으며, 2.0% 첨가(添加)했을 때 최대강도(最大强度)를 나타냈다. 2.인장강도(引張强度)는 7일(日) 강도(强度)에서 염화(鹽化)칼슘을 첨가(添加)한 몰타르가 보통(普通)몰타르보다 높은 강도(强度)를 나타냈으나, 28일(日) 강도(强度)에서는 1.0% 첨가(添加)한 몰타르가 최대강도(最大强度)를 나타냈고, 2.0% 이상(以上) 첨가(添加)한 경우는 보통(普通)몰타르보다 적게 나타났다. 3. 염화(鹽化)칼슘 첨가량(添加量)이 3.0%이상(以上)일 때는 급결현상(急結現象)이 나타났으며 이로 인(因)한 균열 때문에 강도(强度)는 저하(低下)되는 것으로 사료(思料)된다. 4. 부배합(富配合)에서는 압축(壓縮) 및 인장강도(引張强度)가 재령(材令) 7일(日) 이전(以前)에는 강도증진(强度增進)에 효과(效果)가 컸고 재령(材令) 7일(日) 이후(以後)에는 큰 차이가 없었으므로, 염화(鹽化)칼슘을 1.0%~2.0% 첨가(添加)하여 사용(使用)하면 동기공사(冬期工事)에서 초기강도증진(增初期强度進)을 기(期) 할 수 있을 것으로 생각된다.

• Structural Engineering and Mechanics
• /
• 제38권4호
• /
• pp.459-477
• /
• 2011

Due to the low elastic modulus of FRP, concrete members reinforced with FRP rebars show greater deflections than members reinforced with steel rebars. Deflection is one of the important factors to consider the serviceability of horizontal members. In this study flexural test of AFRP reinforced concrete beams was performed considering reinforcement ratio and compressive strength as parameters. The test results indicated that flexural capacity and stiffness increase in proportion to the reinforcement ratio. The test results were compared with existing proposed equations for the effective moment of inertia including ACI 440. The most of the proposed equations were found to over-estimate the effective moment of inertia while the equation proposed by Bischoff and Scanlon (2007) most accurately predicted the values obtained through actual testing.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권3호
• /
• pp.177-185
• /
• 1999

In this study, study about fly ash and blast-furnace slag used as substitutive materials for cement, and the influence on the neutralization of high flow concrete durability with these substitutive materials was performed and analyzed. The results are as follows 1) Aggregate segregation was partially improved with the progress of the admixture input at the mix proportion above slump flow 65 cm 2) Compressive strength with the progress of the increasement of fly ash input was decreased in early age, but decrease range was improved in long term age. Also, in case of blast-furnace, similar or improved compressive strength was appeared. 3) The neutralization depth with fly ash input was noticeably increased. But blast-furnace slag was effective to prevent. 4) In this experiment, high powder content was advantageously affected on preventive effect of the neutralization, and the relationship between the compressive strength and the neutralization depth was inversely proportional.

• Computers and Concrete
• /
• 제25권1호
• /
• pp.83-94
• /
• 2020

The use of fly ash in modern-day concrete technology aiming sustainable constructions is on rapid rise. Fly ash, a spinoff from coal calcined thermal power plants with pozzolanic properties is used for cement replacement in concrete. Fly ash concrete is cost effective, which modifies and improves the fresh and hardened properties of concrete and additionally addresses the disposal and storage issues of fly ash. Soft computing techniques have gained attention in the civil engineering field which addresses the drawbacks of classical experimental and computational methods of determining the concrete compressive strength with varying percentages of fly ash. In this study, models based on soft computing techniques employed for the prediction of the compressive strengths of fly ash concrete are collected from literature. They are classified in a categorical way of concrete strengths such as control concrete, high strength concrete, high performance concrete, self-compacting concrete, and other concretes pertaining to the soft computing techniques usage. The performance of models in terms of statistical measures such as mean square error, root mean square error, coefficient of correlation, etc. has shown that soft computing techniques have potential applications for predicting the fly ash concrete compressive strengths.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.19-22
• /
• 2006

The quantity of Recycled concrete powder is increased, because it hal been ever so often crushing for production of a good quality recycled aggregates This Study is on the Development of Concrete-Product by Using Recycled Concrete Powder and alto for know performance of concrete-producted having low water contents and it is to know for all of performance of concrete-producted having low water contents The conclusions of this study are following. The use of replacement cement is not effective, because it has strengh of less than 10MPa But It is possible to develop high strength concrete-producted having 39MPa above compressive strength by using recycled concrete powder. Because strength enhancement effects by recycled concrete powder are responsible to optimum grading. The conclusions of this study are following. The use of replacement cement is not effective, because it has strengh of less than 10MPa. It is possible to develop high strength concrete-producted having 39MPa above compressive strength by using recycled concrete powder. Because strength enhancement effects by recycled concrete powder are responsible to optimum grading.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.408-415
• /
• 1996

This study is aimed to define the behavior of the girder ledge of precast girder-beam joint in rame type precast concrete construction method. The variable of this study is followed : 1) The change of the maximum shear strength depended on the transformation of concrete compressive strength 2) The change of the behavior of ledge depended on the transformation of shear-span ratio 3) The change of maximum shear strength and ductility by the type of reinforcement. The results of this study show the behavior of ledge is affected by shear-span ratio and the maximum shear strength is depended on the concrete compressive strength, reinforcement ratio and effective section area. In addition, through the investigation of the established study, the results of this study suggest the shear friction formula of Raths.

• Advances in concrete construction
• /
• 제4권4호
• /
• pp.243-261
• /
• 2016

This research study focuses on utilizing sandstone which is overburden waste rock in coal mines to use in concrete as a replacement of fine aggregate. Physical properties of sandstone like water absorption, moisture content, fineness modulus etc., were found to be similar to conventional fine aggregate. Scanning Electron Microscope (SEM) analysis was carried out for analysing elemental composition of sandstone. There was no sulphur content in sandstone which is a good sign to carry the replacement. Fine aggregate was replaced with sandstone at 25%, 50%, 75% and 100% by volume and moulds of concrete cubes and cylinders were prepared. Compressive strength of concrete cubes was tested after 3, 7 and 28 days and split tensile & flexural strength was determined after 28 days. The strength was found to be increasing marginally with increase in sandstone content. Fine aggregate that was replaced by 100% sandstone gave highest strength among all the replacements for the compressive, split tensile and flexural strengths. Though increase in strength was marginal, still sandstone can be an effective replacement for sand in order to save the natural resource and utilize the waste sandstone.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.605-610
• /
• 2002

The purpose of this study is to develop an analytic model which can describe the behavior or concrete compressive member strengthened by CFS(Carbon Fiber Sheet) with various cross-sectional shapes such as circular. square, and octagonal and various laminate angles. The failure criterion of laminated CFS is based on Tsai-Wu failure criterion. The stress strain model of confined concrete compressive member is based on an equation proposed by Mander. The effective lateral confining pressure is considered and modified according to various cross-sectional shapes. Octagonal cross-section shows the best results in the aspect of ductility, while circular does in compressive strengthening effects. In addition, [0/0/0/0] laminate in which the direction of fiber is parallel to the direction of principal stress shows the superior strength and ductility than other laminates. The analytic results show that strength and ductility of the analytic model depend on the cross-sectional shapes as well as the laminate angles.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문 발표회
• /
• pp.23-26
• /
• 2003

This study is intended to investigate the properties of early strength development by application of TEA to the field. According to the results, when TEA is added, fluidity is almost same to base concrete, and increases upto aimed slump after field flowing. Setting time does not differ in the case of base and TEA, but retarded after flowing. The time when compressive strength gains 5 MPa, which side form can be removed, is 23 hours, and so the removal time is shortened by I hours in comparison with plain concrete. But compressive strength is almost same to that of plain concrete at 28 days. The rebound value of P type schmidt hammer show similar tendency to compressive strength, and the rebound value of structure is higher than that of standard curing specimen due to heat capacity effect and drying by the air outside. Therefore, it is thought that if the rebound value of P type schmidt hammer is controled. by about 26 in consideration of open air environment, it is very effective to determine the removal time of side forms.

• 한국농공학회논문집
• /
• 제58권2호
• /
• pp.83-90
• /
• 2016

This study was performed to evaluate the effective analysis of flexural performance for polypropylene fiber (PF) reinforced EVA concrete that can be used in marine bridge, tunnel and agricultural structures under flexural load. The control design was applied in ready mixed concrete using 10 % fly ash of total binder weight used in batch plant. On the basis of the control mix design, there was designed mix types that contained PF ranged from 0 % to 0.5 % by volume ratio into two mix types of using 0 % and 5.0 % EVA contents of total binder weight. Before evaluating the flexural performance, we tested compressive strength and flexural strength to evaluate whether polypropylene fiber reinforced concrete could be used or not in site. The method of flexural performance evaluation was applied by ASTM C 1609. These results showed the maximum compressive strength and flexural strength was measured at each E5P1 and E5P2. Concrete reinforced with PF exhibited deflection-softening behavior. In the concrete reinforced with 0.4 % PF contents and containing 5.0 % EVA, the flexural performance was the best.