• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.41.2-41.2
• /
• 2018

EL CVn-type eclipsing binaries are composed of a massive A-type main-sequence primary star and a hotter B-type secondary one. These are worthy of particular attention because the secondary stars are rare objects to be extremely low-mass white dwarf precursors (ELM proto-WD) with the mass of ${\leq}0.2M_{\odot}$, evolving to higher effective temperatures and higher surface gravities. A few of them were discovered to show multi-periodic pulsations in one or both components. We monitored one of these rare and interesting objects, J0247-25 (=1SWASP J024743.37-251549.2), at two KMTNet sites of SAAO in South Africa and SSO in Australia. The observations were performed with the KMTNet 1.6m telescopes and pre-science 4K CCD cameras during the system test run from July to November 2014. Using the photometric data obtained for a total of 23 nights, we constructed well-defined eclipsing light curves in B/V-bands and derived absolute parameters (mass and radius, etc.) of each binary component. After subtracting model eclipsing curves from the data, we detected seven frequencies with 33~53 cycles per day (c/d) and identified them to be Delta Sct-type pulsations originated from the A-type primary component. Five frequencies were turned out to be excited by rotational splitting of non-radial pressure modes, enabled us to investigate rotational properties. We could not detect any frequency higher than 100 c/d, implying that pulsation amplitudes of the proto-WD secondary decrease greatly.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.40.1-40.1
• /
• 2016

Recent integral-field spectrograph surveys have found that similar-looking early type galaxies have wide range of rotational properties (Emsellem et al. 2007). This finding initiated a new point of view to the galaxies; rotation of galaxy as the first parameter of galaxy classification (Emsellem et al. 2011, Cappellari et al. 2011, for example). Some theoretical studies tried to address the origin of galaxy rotation. Idealized galaxy merger simulations have shown that galaxy-galaxy interactions have significant effects on the rotation of galaxies. Cosmological simulations by Naab et al. 2014 also added some more insights to the rotation of galaxies. However, previous studies either lack cosmological background or have not enough number of samples. Running a set of cosmological hydrodynamic zoom-in simulations using the AMR code RAMSES(Teyssier 2002). we have constructed a sample of thousands of galaxies in 20 clusters. Here we present a kinematic analysis of a large sample of galaxies in the cosmological context. The overall distribution of rotation parameter of simulated galaxies suggests a single peak corresponding to fast rotating galaxies. But when divided by mass, we find a strong mass dependency of galaxy rotation, and massive galaxies are distinctively slow rotating. The cumulated effective of mergers seems to neutralize galaxy rotation as suggested by previous studies (Khochfar et al. 2011, Naab et al. 2014, and Moody et al. 2014). This is consistent with the fact that massive galaxies tend to rotate more slowly after numerous mergers. However, if seen individually, merger can either increase or decrease galaxy rotation depending on mass ratio, orbital parameter, and relative rotation axis of the two galaxies. This explains the existence of some non-slow rotating massive early type galaxies.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.6
• /
• pp.272-280
• /
• 2021

The influence of acetylene flow rates on the carburizing behavior of an AISI 4115 steel in 1 ton-class mass production-type vacuum carburizing furnace has been studied through microstructure, carbon concentration, hardness analyses. The AISI 4115 steels were carburized with various flow rates (20, 32.7, 60 l/min) and locations in the furnace (top, center, bottom) at 950℃. The acetylene flow rate played an important role in controlling the carburizing properties of carburized samples, such as effective case depth and uniformity carburizing according to location in the furnace. At an acetylene flow rate of 20 l/min, the carburized samples had a shallow average hardened layer (0.645 mm) compared to the target hardening depth (1 mm) due to low carbon flux and spatial uniformity of carburization (17.8%) in the furnace. At a flow rate of 60 l/min, the carburized samples showed an average hardened layer (1.449 mm) deeper than the target hardening depth and had the spatial uniformity of carburization (98.8%). In particular, at a flow rate of 32.7 l/min, the carburized samples had an average hardened layer (1.13 mm) close to the target hardening depth and had the highest carburizing uniformity (99.1%). As a result, an appropriate flow rate of 32.7 l/min was derived to satisfy the target hardening depth and to have spatial uniform hardened layer in the furnace.

• Membrane and Water Treatment
• /
• v.13 no.5
• /
• pp.235-243
• /
• 2022

The paper presents the effect of operating temperatures and flow rates on the distillate flux that can be obtained from a hydrophobic membrane having the characteristics: pore size of 0.15 ㎛; thickness of 130 ㎛; and 85% porosity. That membrane in the present investigation could be the direct contact (DCMD) or the air-gap membrane distillation (AGMD). To model numerically the membrane distillation processes, the two-dimensional computational fluid dynamic (CFD) is used for the DCMD and AGMD cases here. In this work, DCMD and AGMD models have been validated with the experimental data using different flows (Parallel and Counter-current flows) in non-steady-state situations. A good agreement is obtained between the present results and those of the experimental data in the literature. The new approach in the present numerical modeling has allowed examining effects of the nature of materials (Polyvinylidene fluoride (PVDF) polymers, copolymers, and blends) used on thermal properties. Moreover, the effect of the area surface of the membrane (0.021 to 3.15 ㎡) is investigated to explore both the laminar and the turbulent flow regimes. The obtained results found that copolymer P(VDF-TrFE) (80/20) is more effective than the other materials of membrane distillation (MD). The mass flux and thermal efficiency reach 193.5 (g/㎡s), and 83.29 % using turbulent flow and an effective area of 3.1 ㎡, respectively. The increase of feed inlet temperatures and its flow rate, with the reduction of cold temperatures and its flow rate are very effective for increasing distillate water flow in MD applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.382-382
• /
• 2012

CIGS thin films have received great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films are deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. The deposition technique is one of the most important processes in preparing CIGS thin film solar cells. Among these methods, co-evaporation is one of the best technique for obtaining high quality and stoichiometric CIGS films. However, co-evaporation method is known to be unsuitable for commercialization. The sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have prepared by rf magnetron sputtering using a $Cu(In_{1-x}Ga_x)Se_2$ single quaternary target without post deposition selenization. This process has been examined by the effects of deposition parameters on the structural and compositional properties of the films. In addition, we will explore the influences of substrate temperature and additional annealing treatment after deposition on the characteristics of CIGS thin films. The thickness of CIGS films will be measured by Tencor-P1 profiler. The crystalline properties and surface morphology of the films will be analyzed using X-ray diffraction and scanning electron microscopy, respectively. The optical properties of the films will be determined by UV-Visible spectroscopy. Electrical properties of the films will be measured using van der Pauw geometry and Hall effect measurement at room temperature using indium ohmic contacts.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.158-158
• /
• 2011

$Cu(In_xGa_{1-x})Se_2$ (CIGS) thin film solar cell is one of the most promising solar cells in photovoltaic devices. CIGS has a direct band gap which varied from 1.0 to 1.26 eV, depending on the Ga to In ratio. Also, CIGS has been studying for an absorber in thin film solar cells due to their highest absorption coefficient which is $1{\times}10^5cm^{-1}$ and good stability for deposition process at high temperature of $450{\sim}590^{\circ}C$. Currently, the highest efficiency of CIGS thin film solar cell is approximately 20.3%, which is closely approaching to the efficiency of poly-silicon solar cell. The deposition technique is one of the most important points in preparing CIGS thin film solar cells. Among the various deposition techniques, the sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have been prepared by rf magnetron sputtering method using a single target. The optical and structural properties of CIGS films are generally dependent on deposition parameters. Therefore, we will explore the influence of deposition power on the properties of CIGS films and the films will be deposited by rf magnetron sputtering using CIGS single target on Mo coated soda lime glass at $500^{\circ}C$. The thickness of CIGS films will be measured by Tencor-P1 profiler. The optical properties will be measured by UV-visible spectroscopy. The crystal structure will be analyzed using X-ray diffraction (XRD). Finally the optimal deposition conditions for CIGS thin films will be developed.

• Journal of Microbiology and Biotechnology
• /
• v.27 no.9
• /
• pp.1639-1648
• /
• 2017

Curcumin is a natural polyphenolic compound, widely acclaimed for its antioxidant, anti-inflammatory, antibacterial, and anticancerous properties. However, its use has been limited due to its low-aqueous solubility and poor bioavailability, rapid clearance, and low cellular uptake. In order to assess the effect of glycosylation on the pharmacological properties of curcumin, one-pot multienzyme (OPME) chemoenzymatic glycosylation reactions with UDP-${\alpha}-{\text\tiny{D}}$-glucose or UDP-${\alpha}-{\text\tiny{D}}$-2-deoxyglucose as donor substrate were employed. The result indicated significant conversion of curcumin to its glycosylated derivatives: curcumin 4'-O-${\beta}$-glucoside, curcumin 4',4"-di-O-${\beta}$-glucoside, curcumin 4'-O-${\beta}$-2-deoxyglucoside, and curcumin 4',4"-di-O-${\beta}$-2-deoxyglucoside. The products were characterized by ultra-fast performance liquid chromatography, high-resolution quadruple-time-of-flight electrospray ionization-mass spectrometry, and NMR analyses. All the products showed improved water solubility and comparable antibacterial activities. Additionally, the curcumin 4'-O-${\beta}$-glucoside and curcumin 4'-O-${\beta}$-2-deoxyglucoside showed enhanced anticancer activities compared with the parent aglycone and diglycoside derivatives. This result indicates that glycosylation can be an effective approach for enhancing the pharmaceutical properties of different natural products, such as curcumin.

• Nuclear Engineering and Technology
• /
• v.55 no.9
• /
• pp.3441-3449
• /
• 2023

We determined the radiation shielding properties for 10CaO-xPbO-(90-x) deteriorated silica gel (DSG) glass system (x = 20, 25, 30, 35, 40, and 45 mol.%). The mass attenuation coefficient (MAC) has been estimated at photon energies of 74.23, 97.12, 122, 662, 1173, and 1332 keV using a narrow beam X-ray attenuation and transmission experiment, the XCOM program, and a PHITS simulation. The obtained MAC values were applied to estimate the half value layer (HVL), mean free path (MFP), effective atomic number, and effective electron density. Results show that the MAC value of the studied glasses ranges between 0.0549 and 1.4415 cm²/g, increases with the amount of PbO, and decreases with increasing photon energy. The HVL and MFP values decrease with increasing PbO content and increase with increasing photon energy. The recycled glass, with the addition of PbO content (20-45 mol.%), exhibited excellent radiation shielding capabilities compared to standard barite and ferrite concretes and some glass systems. Moreover, the experimental radiation shielding parameters agree with the XCOM and PHITS values. This study suggests that this new waste-recycled glass is an effective and cost-saving candidate for X-ray and gamma-ray shielding applications.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.282-293
• /
• 2021

This paper examines gamma-ray shielding properties of SBC-Bx glass system with the chemical composition of 40SiO₂-10B₂O₃-xBaO-(45-x)CaO- yZnO- zMgO (where x = 0, 10, 20, 30, and 35 mol% and y = z = 6 mol%). Mass attenuation coefficient (µ/ρ) which is an essential parameter to study gamma-ray shielding properties was obtained in the photon energy range of 0.015-15 MeV using PHITS Monte Carlo code for the proposed glasses. The obtained results were compared with those calculated by WinXCOM program. Both the values of PHITS code and WinXCOM program were observed in very good agreement. The (µ/ρ values were then used to derive mean free path (MFP), electron density (N_eff), effective atomic number (Z_eff), and half value layer (HVL) for all the glasses involved. Additionally, G-P method was employed to estimate exposure buildup factor (EBF) for each glass in the energy range of 0.015-15 MeV up to penetration depths of 40 mfp. The results reveal that gamma-ray shielding effectiveness of the SBC-Bx glasses evolves with increasing BaO content in the glass sample. Such that SBC-B35 glass has superior shielding capacity against gamma-rays among the studied glasses. Gamma-ray shielding properties of SBC-B35 glass were compared with different conventional shielding materials, commercial glasses, and newly developed HMO glasse. Therefore, the investigated glasses have potential uses in gamma shielding applications.

• Journal of Microbiology and Biotechnology
• /
• v.12 no.2
• /
• pp.301-305
• /
• 2002

The gene (ppaT) encoding Thermus caldophilus GK24 pyrophosphatase (Tca pyrophosphatase) was cloned and sequenced. The gene was found to contain an open reading frame encoding 175 amino acids with a calculated mass of 19,155 Da. The ppaT gene was expressed under the control of the tac promoter in Escherichia coli. The recombinant Tca pyrophosphatase was purified 21.4-fold with $56\%$ yield and specific activity of 25.7 U $mg^-1$, following a combination of heating (to denature the E. coli proteins) and one step of DEAE-Sephacel column chromatography. The native enzyme was found to have an approximate molecular mass of 110,000 Da and consisted of six subunits. The enzyme exhibited maximal activity at pH of 8.0-8.5 and was stable at $80-90^{\circ}C$. A divalent cation was absolutely required for the enzyme activity, with $Mg^2+$. being the most effective.