• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1857-1859
• /
• 2004

It is widely known that the ultra high frequency (UHF) method that detects the electromagnetic wave of the PD pulses in the gas insulated space is one of the most competitive methods for its high sensitivity. From the above point of view, this paper describes the noise suppression methods and the PD measurement results of the in-service substation by the developed UHF PD measurement system which consists of the external UHF coupler, the UWB LNA and the digital storage oscilloscope. As results, it was found that the effect of the noise suppression methods were verified and that the developed external UHF coupler showed a better detection sensitivity than a conventional external coupler.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.124-129
• /
• 2004

The ratio pyrometry has been investigated experimentally for the measurement of soot particle temperatures in a diffusion flame. A tungsten lamp calibration system was constructed and used in order to calibrate the ratio pyrometry and two-color pyrometry using a KL-factor method. Once the ratio pyrometry is properly calibrated, temperatures measured using a ratio pyrometry were virtually identical to those obtained from a KL-factor method. The effect of soot volume fraction on temperature measurement was almost negligible, and therefore, the ratio pyrometry could provide the useful temperature information of sooting flames. The potential application of a ratio pyrometry to a 2-D temperature measurement without sacrificing the accuracy was demonstrated.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.2
• /
• pp.67-71
• /
• 2012

Page-oriented holographic data storage (HDS) is very sensitive to the tilt error. Therefore, tilt error should be measured and compensated. Especially, mechanical tilt measurement method cannot cope with tilt error measurement because photopolymer medium has shrinkage problem. Therefore, the method to solve this problem is using the reconstructed image which can represent both tilt and shrinkage effect. In this paper, we suggest disc tilt measurement algorithm using image pattern of retrieval data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1173-1176
• /
• 2007

The breaker noise is one of the main noise sources of construction site. It is very important to assess and measure the breaker noise accurately, because the noise labelling will be in effect January 2008 in Korea. Therefore, It is necessary to measure the sound power level of breakers and use a appropriate test method in accordance with international standard. In this study, we measure the sound power level of breakers by using the breaker noise measurement system. This system makes it possible to measure the breaker noise more accurately than to measure the noise of that attached with excavator, because this system can control main factors affecting breaker noise such as hydraulic input power, hydraulic supply pressure, breaker inlet oil flow and so on.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.406-410
• /
• 1991

This paper presents an improved algorithm of optimal measurement system design with a reliability evaluation method for large power system. The proposed algorithm is developed to consider the dummy bus and to achieve highest accuracy of the state estimator as well with the limited Investment cost. The dummy bus in the power system is impossible to install measurement meter, while real and reactive power measurement values are exactly zero. Thus, the effect on these dummy bus measurements is considered in the proposed algorithm. On the other hand, P/C model is developed by taking advantage of the matrix sparsity. The improved program is successfully tested for KEPCO system with PSS/E lineflow calculated data package.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1038-1041
• /
• 2004

In this study, developed a micro-level experimental setup to measure pore pressure and poroelastic modulus in various strain and strain rate about a stress in micro-structure of bone tissue. It is essential device in the development of the model to analysis the interstitial bone fluid flow of the lacuno-canalicular system to be known that would effect on the bone remodeling. The constitution of the experimental setup is as follows, microscopic image processing system; actuator control unit; load measurement system. A pilot study was used an artificial chemical wood to have similar poroelastic property of bone matrix and conducted to validate the suitability of the measurement system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1359-1367
• /
• 2001

Improvement of machine tool accuracy is an essential part of quality control in manufacturing process. Among of all the errors of a particular machine tool, the thermal errors of the spindle have a notably significant effect on machining accuracy and have a direct influence upon both the surface finish and geometric shape of the finished workpiece. Therefore, this paper proposed new measurement method for thermal errors of the spindle in machine tools. The thermal errors are measured by a ball bar system instead of capacitance sensor system. The novel measurement method using ball bar system is more efficient, easier to use than conventional measurement system. And also the ball bar system is possible to measure both geometric errors and thermal errors at the same time.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.231-234
• /
• 2007

A measurement technique in an industry site is basis technique which is bringing a ripple effect on an increasing productivity. Recently, a measurement request is increasing in the industry field as well as the variety field such as leisure, research. Thus, it is in point of time to secure an internal technique about measurement using a laser. In this paper, we prepare to develop the industrial precision laser distance measure device that is available measuring in several hundred meters[m]. In other words, we are planning to measure a wide distance using a laser diode that has long life and is compact, inexpensive. Through this research, we'll secure the pulse laser control technique, a signal processing, technique for distance calculation about a laser distance measurement system. And hereafter, we'll plan to commercialize a laser distance device using this research.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.625-627
• /
• 2005

Existent distance measurement that use camera is method that use both Stereo Camera and Monocular Camera, There is shortcoming that method that use Stereo Camera is sensitive in effect of a lot of expenses and environment variables, and method that use Monocular Camera are big computational complexity and error. In this study, reduce expense and error using Monocular Camera and I suggest algorithm that measure distance, Extract features using scale Invariant features Transform(SIFT) for distance measurement, and this measures distance through features matching and geometrical analysis, Proposed method proves measuring distance with wall by geometrical analysis free wall through feature point abstraction and matching.