• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.400-407
• /
• 1995

The straightness property is one of fundamental geometric tolerances to be strictly controlled for guideways of machine tools and measuring machines. The staightness measurement for long guideways was usually difficult to perform, and it needed additional equipments or special treatment with limited application. In this paper, a new approach is proposed using the profile matching technique for the long guideways, which can be applicable to most of straghtness measurements. An edge of relativelly sthort length is located along a divided section of a long guideway, and the local straightness measurement is performed. The edge is then moved to the next section with several positions overlap. After thelocal straightness profile is measured for every section along the long guideway with overlap, the global straightness profile is constructed using the profile matching technique based on theleast squares method. The proposed techinique is numerically tested for two cases of known global straightness profile arc profile and irregular profile and those profiles with and without random error intervention, respectively. When norandom errors are involved, the constructed golval profile is identical to the original profile. When the random errors are involved, the effect of the number of overlap points are investigated, and it is also found that the difference between the difference between the constructed and original profiles is very close to the limit of random uncertainty with juist few overlap points. The developed technique has been practically applied to a vertical milling machine of moving table type, and showed good performance. Thus the accuracy and efficiency of the proposed method are demonstrated, and shows great potential for variety of application for most of straightness measuirement cases using straight edges, laser optics, and angular measurement equipments.

• 산업공학
• /
• 제13권4호
• /
• pp.703-708
• /
• 2000

In manufacturing processes, manufacturing features always deviate somewhat from their nominal design specifications due to several types of errors. This study suggests a fitting algorithm of the geometric profile parameters of leading and trailing edges for turbine compressor airfoils. In reality, industry personnels inspect the airfoil profile by trial-and-error method to determine the geometric feature parameters. In this study we propose an exploration approach based on factorial design with center point to minimize the effect of measurement errors caused by probe slip. By adopting the fitting method developed in this paper, one can enhance the precision and efficiency of fitting the airfoil edge profile.

• 산업공학
• /
• 제15권4호
• /
• pp.432-438
• /
• 2002

When the trailing edge and leading edge of an airfoil contour of high pressure compressor blades are measured, there exists a measurement error due to the size of the probe stylus ball diameter. In the paper an experimental study is provided to determine the optimum diameter of the probe stylus in inspecting the airfoil of the high pressure compressor blade. The measurement and analysis procedure suggested in this paper will be helpful to those who are involved in measuring and inspecting various types of blades.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.595-600
• /
• 1998

Train wheels tend to wear abrasion due to frequent Starlings and brakings. They are important factors of train safety and noise. However, it is difficult and inaccurate to measure their shape and profile manually. Profile measurement system of train wheel with image processing is proposed. The system consists of CCD cameras, PCI image grabber board, and PC operated on Windows '95. Image processing algorithms such as filtering, histogram equalization, and edge detection are presented, and some processing results are illustrated.

• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.76-81
• /
• 2006

In this paper, profile error measurement method of a turbine blade using 3D-scanner is developed. The method begins with scanning the upper and lower sides of the blade on which three small balls are attached, and constructs a solid measurement model by registering the two scanned surfaces. Airfoils are derived from the model at each interval by intersecting it with a plane, and arranged with design airfoils. The $2^2$ factorial design search method is engaged in arranging the two airfoils, from which the main blade parameters including the edge radius are computed. The developed measurement technique is applied to practical blade manufacturing and validates its effectiveness.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권2호
• /
• pp.54-58
• /
• 2007

This paper describes an atomic force microscope (AFM)-based instrument for measuring the nanoscale cutting edge profiles of diamond cutting tools. The instrument consists of a combined AFM unit and an optical sensor to align the AFM tip with the top of the diamond cutting tool edge over a submicron range. In the optical sensor, a aser beam is emitted from a laser diode along the Y-axis and focused to a small beam spot with a diameter of approximately $10{\mu}m$ at the beam waist, which is then received by a photodiode. The top of the tool edge is first brought into the center of the beam waist by adjusting it in the X-Z-plane while monitoring the variation in the photodiode output. The cutting tool is then withdrawn and its top edge position at the beam center is recorded. The AFM tip can also be positioned at the beam center in a similar manner to align it with the top of the cutting edge. To reduce electronic noise interference on the photodiode output and thereby enhance the alignment accuracy, a technique is applied that can modulate the photodiode output to an AC signal by driving the laser diode with a sinusoidal current. Alignment experiments and edge profile measurements of a diamond cutting tool were carried out to verify the performance of the proposed system.

• 한국생산제조학회지
• /
• 제5권2호
• /
• pp.57-62
• /
• 1996

Basically, the idea underlying most edge-detection technique is the computation of a local derivative operator used for edge detection in gray level image. This concept can be easily illustrated with the aid of object which shows an image of a simple lilght on a dark background, Using the gray level profile along a horizontal scan line of the image. the first and second derivatives of it were acquired. This study is to develop an automatic measuring system based on the digital image processing which can be applied to the real time measurement of the characteristics of the ultra-thin thickness. The experimental results indicate that the developed automatic inspection can be applied in real situation.

• 대한원격탐사학회지
• /
• 제26권5호
• /
• pp.527-536
• /
• 2010

본 논문에서는 영상의 품질 지표인 GRD(Ground Resolved Distance) 측정에 있어서 인공표적만을 이용하던 기존의 측정방식과는 다르게 지표상에 분포하고 있는 자연표적만을 이용하여 신뢰성 있는 GRD 산출이 가능하도록 새로운 방식의 GRD 측정가법을 고안하였다. 자연표적에서 활용 가능한 Edge Profile 추출기법을 개발하여 추출 정확도 및 안정성을 분석하였으며 그 결과, 자연표적을 이용할 경우 본 논문의 추출방식이 가장 적합한 방식임을 확인 할 수 있었다. 이를 적용한 GRD 측정기법의 정확도와 자연 표적에서의 활용 가능성을 평가하기 위해 육안분석결과를 보유하고 있는 인공표적영상과 인공표적이 된 인공위성영상을 이용하여 GRD 측정 실험을 수행하였다. 인공표적영상에서의 GRD 측정결과는 육안분석 결과와 매우 유사하여 높은 정확도를 보여주었으며 인공위성영상에서의 GRD 측정결과, 자연표적과 인공표적에서의 GRD 측정값이 유사하게 나타났다. 이는 제안한 GRD 측정기법을 이용하여 자연표적만으로도 신뢰성 있는 GRD 측정이 가능함을 보여준다.

• 방사선산업학회지
• /
• 제17권4호
• /
• pp.377-384
• /
• 2023

In this study, the image quality assessment, especially spatial resolution evaluation, for Sparse-view CT reconstructed images was performed. The main goal of the experiment is to evaluate Modulation Transfer Function by using American Standard Method for Measurement of Computed Tomography System Performance(ASTM E1695-95) which uses the edge test object. To compare with the ASTM method, a different method, the radial-type edge profile, to measure MTF using the edge method also performed. Both approaches were tested on the same image acquired by the stationary-gantry sparse-view CT security-screening system using cylindrical test phantom manufactured in accordance with ANSI 42.45. Both of the spatial resolutions at 10% modulation are 0.195, 0.203lp pixel^-1, respectively. The method implemented by ASTM E1695-95 showed higher reliability and had a relatively more accurate spatial resolution result than the radial-type edge profile method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.395-401
• /
• 1993

The purpose of this paper is to develop an automatic measuring system based on the digital image processing which can be applied to the in-process measurement of the characteristics of the thin thickness. The derivative operators is used for edge detection in gray level image. This concept can be easiliy illustrated with the aid of object shows an image of a simple light object on a dark background, the gray level profile along a horizontal scan line of the image, and the first and second derivatives of the profile. The first derivative of an edge modeled in this manner is () in all regions of constant gray level, and assumes a constant value during a gray level transition. The experimental results indicate that the developed qutomatic inspection system can be applied in real situation.