• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.6
• /
• pp.533-538
• /
• 2014

We fabricated grooved mushroom structures with anisotropic wettability on silicon substrates using basic MEMS processes. The geometry of these grooved mushroom structures could be changed by controlling the additional IPA solution during Si etching by TMAH solution. To understand anisotropic wettability, contact angles (CAs) of hexadecane droplets were measured in the orthogonal and parallel directions to grooved lines. The CA measurement results displayed anisotropic wetting on the grooved mushroom structures. However, specimens with $80{\mu}m$ distance between top layers displayed isotropic and superoleophobic wetting. This study demonstrates that the thickness of the top layer is more critical than the width or height of the ridge when determining the wettability of organic solvent. Despite the wide distance between top layers ($80{\mu}m$), the specimen with a thin top layer (100 nm) showed highly anisotropic wetting and low CA due to the pinning of droplets at the edge of the top layer.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.4
• /
• pp.76-85
• /
• 1993

The purpose of this study was to analyze the wind force distribution on the two single-span arched plastic house depending upon the house spacing and wind direction, which may provide the fundamental criteria for the structural design. In order to specify the wind force distribution, the variation of the wind force coefficients, the mean wind force coefficients and the drag force coefficients were estimated from the wind tunnel test data. The results obtained are as follows : 1. At the wind direction of 90$^{\circ}$, there was a typical span interval at which the maximum negative pressure was occured at the edge of the inside walls. 2. In the consideration of wind loads, the wind force coefficients estimated from independent single-span arched plastic house should not be directly applied to the structural design on the double houses separated. 3. The average maximum negative wind force on the inside walls was occured at the wind direction of 90$^{\circ}$, and the variations depending on the span intervals was not significant. 4. The average maximum drag force was occured at the wind direction of 300, and the magnitude of drag force was more significant at the first house. As the distance between two houses was increased, the drag force was slightly increased for every wind direction.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.4
• /
• pp.58-64
• /
• 2009

This aim of the study is to demonstrate the effect of a photovoltaic module installed on a small wind-photovoltaic hybrid generation system. Computational fluid dynamics(CFD) is used to interpret the velocity field around the photovoltaic module and the blade areas of a wind turbine. According to the simulation results, it is obvious that x_velocity and y_velocity varies very significantly with time near the photovoltaic module. This would lead to an increase of periodic wind load caused by flow separation at the edge of the photovoltaic module. This study discusses the flow characteristics in term of velocity and frequency analysis. Moreover we suggest a distance between a photovoltaic module and a wind turbine to avoid partially the negative effect caused by the photovoltaic module.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.162-165
• /
• 2017

The proposed paper extracts the region of interest from the x-lay input image and compares it with the reference image. The x-ray image has the same shape, but the size, direction and position of the object are photographed differently. In this way, we measure the erection difference of darkness and darkness using the similarity measurement method for the same object. Distance measurement also calculates the distance between two points with vector coordinates (x, y, z) of x-lay data. Experimental results show that the proposed method improves the accuracy of ROI extraction and the reference image matching time is more efficient than the conventional method.

• Radiation Oncology Journal
• /
• v.9 no.2
• /
• pp.333-336
• /
• 1991

High energy Photon beam has a sharp beam margin due to a less side scatter and the other things. But there still remains a penumbra where the dose changes rapidly in the region near the edge of a radiation beam, although it is short in width. It is suggested that the width of the penumbra depends on the source size, distance from source to diaphragm, source to skin distance, and depth in tissue. However, it is also supposed that the other factors influence the penumbra width. In this paper, we investigate changes of the physical penumbra widths according to various field sizes and depths, by using the three dimensional dosimetry system. As a result, we found that as field size and depth increase, the physical penumbra width also increases.

• Journal of Korea Multimedia Society
• /
• v.17 no.10
• /
• pp.1205-1212
• /
• 2014

In this paper, we propose a high-quality stitching method of 3D multiple dental CT images. First, a weighted function is generated using the difference of two distance functions that calculate a distance from the nearest edge of an overlapped region to each position. And a blending ratio propagation function for two gradient vectors is parameterized by the difference and magnitude of gradient vectors that is also applied by the weighted function. When the blending ratio is propagated, an improved region growing scheme is proposed to decide the next position and calculate the blending intensity. The proposed method produces a high-quality stitching image. Our method removes the seam artifact caused by the mean intensity difference between images and vignetting effect. And it removes double edges caused by local misalignment. Experimental results showed that the proposed method produced high-quality stitching images for ten patients. Our stitching method could be usefully applied into the stitching of 3D or 2D multiple images.

• Journal of Information Processing Systems
• /
• v.17 no.1
• /
• pp.63-74
• /
• 2021

According to the double-phase cluster-head election method (DCE), the final cluster heads (CHs) sometimes are located at the edge of cluster. They have a long distance from the base station (BS). Sensor data is directly transmitted to BS by CHs. This makes some nodes consume much energy for transmitting data and die earlier. To address this problem, energy efficient multi-hop cluster-head election strategy (EEMCE) is proposed in this paper. To avoid taking these nodes far from BS as CH, this strategy first introduces the distance from the sensor nodes to the BS into the tentative CH election. Subsequently, in the same cluster, the energy of tentative CH is compared with those of other nodes, and then the node that has more energy than the tentative CH and being nearest the tentative CH are taken as the final CH. Lastly, if the CH is located at the periphery of the network, the multi-hop method will be employed to reduce the energy that is consumed by CHs. The simulation results suggest that the proposed method exhibits higher energy efficiency, longer stability period and better scalability than other protocols.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.9
• /
• pp.156-166
• /
• 1995

This paper presents a bin picking method using a slit beam laser in which a robot recognizes all of the unoccluded objects from the top of jumbled objects, and picks them up one by one. Once those unoccluded objects are removed, newly developed unoccluded objects underneath are recognized and the same process is continued until the bin gets empty. To recognize unoccluded objects, a new algotithm to link edges on slices which are generated by the orthogonally mounted laser on the xy table is proposed. The edges on slices are partitioned and classified using convex and concave function with a distance parameter. The edge types on the neighborhood slices are compared, then the hamming distances among identical kinds of edges are extracted as the features of fuzzy membership function. The sugeno fuzzy integration about features is used to determine linked edges. Finally, the pick-up sequence based on MaxMin theory is determined to cause minimal disturbance to the pile. This proposed method may provide a solution to the automation of part handling in manufacturing environments such as in punch press operation or part assembly.

• Journal of applied mathematics & informatics
• /
• v.41 no.3
• /
• pp.511-524
• /
• 2023

An L(p₁, p₂, p₃, . . . , p_m)-labeling of a graph G is an assignment of non-negative integers, called as labels, to the vertices such that the vertices at distance i should have at least pi as their label difference. If p₁ = 4, p₂ = 3, p₃ = 2, p₄ = 1, then it is called a L(4, 3, 2, 1)-labeling which is widely studied in the literature. A L(4, 3, 2, 1)-path coloring of graphs, is a labeling g : V (G) → Z⁺ such that there exists at least one path P between every pair of vertices in which the labeling restricted to this path is a L(4, 3, 2, 1)-labeling. This concept was defined and results for some simple graphs were obtained by the same authors in an earlier article. In this article, we study the concept of L(4, 3, 2, 1)-path coloring for complete bipartite graphs, 2-edge connected split graph, Cartesian product and join of two graphs and prove an existence theorem for the same.

• Geomechanics and Engineering
• /
• v.38 no.3
• /
• pp.261-273
• /
• 2024

This study presents a groundbreaking analytical approach to find an exact solution for the bearing capacity of strip footings on reinforced slopes, utilizing the two-phase approach and slip line method. The two-phase approach is considered as a generalized homogenization technique. The slip line method is leveraged to derive the stress field as a lower bound solution and the velocity field as an upper bound solution, thereby facilitating the attainment of an exact solution. The key finding points out the variation of the bearing capacity factor N_γ with influencing factors including the backfill soil friction angle, the footing setback distance from the slope crest edge, slope angle, strength, and volumetric fraction of inclusion layers. The results are evaluated by comparing them with those of relevant studies in the literature considering analytical and experimental studies. Through the application of the two-phase approach, it becomes feasible to determine the tensile loads mobilized along the inclusion layers associated with the failure zone. It is attempted to demonstrate the results by utilizing non-dimensional graphs to clearly illustrate variable impacts on reinforced soil stability. This research contributes significantly to advancing geotechnical engineering practices, specifically in the realm of static design considerations for reinforced soil structures.