• 대한수의학회지
• /
• 제35권2호
• /
• pp.361-368
• /
• 1995

Basal cell tumors from 53 dogs were examined histologically and classified as basal cell adenoma(n=44), granular basal cell adenoma(n=1), basal cell carcinoma(n=3), basosquamous cell adenoma(n=1), basosquamous carcinoma(n=4) on the basis of malignancy and squamous metaplasia. Female was twenty three and male was thirty. Affected dogs are usually 5.6 years and sex predilection have not been seen. None of tumor examined was metastasized into other organs. Distinct patterns identified in the basal cell adenoma are solid(n=15), cystic(n=13), adenoid(n=8), medusa(n=5) and ribbon(n=3). Solid basal cell adenoma is common type in benign basal cell adenoma. Only one neoplasm was granular basal cell adenoma which was characterized by eccentric nucleus and abundant granular cytoplasm. Basal cell carcinoma showed anaplastic appearance histologically and had atypical basaloid epithelial cells and multinucleated giant cells with moderate number of mitotic figures. Both basosquamous cell adenoma and carcinoma had squamous metaplasia.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.260-265
• /
• 1997

Large dynamic loads act on the rotor in rotary compressors. There are unbalance forces due to eccentric rotation parts and gas forces induced by the difference in pressure between compression and suction gases6 Rotor-journal bearing system is nonlinear since the stiffness and damping coefficients of the lubricating oil film are not constant in the bearings. In this paper, the program for predicting the behaviors of rotor-journal bearing system of rotary compressor is developed. Finite element modeling is used to analyze the flexible rotor. The numerical results are compared with experimental results. The location of balancer weight are suggested for reducing rotor whiring displacement.

• The Journal of Advanced Prosthodontics
• /
• 제4권3호
• /
• pp.170-173
• /
• 2012

Correct occlusal relationships are part of the successful prosthetic treatment for edentulous patients. Fabrication of complete dentures comprises of clinical and laboratory procedures that should be executed accurately for achieving success with fabricated dentures. Errors occurring during the clinical and laboratory procedures of a denture may subsequently lead to the occlusal errors in the final prosthesis. These occlusal errors can be corrected in two ways: i) in patient's mouth ii) by recording new centric relation and remounting dentures on an articulator. The latter method is more feasible because the mobility of denture base on the mucosa in oral cavity does not permit the identification of premature contacts in centric occlusion and tooth guided eccentric excursions. This article describes a modest and effective clinical chair-side remount procedure using customized mounting platforms.

• Journal of Medicine and Life Science
• /
• 제17권1호
• /
• pp.21-24
• /
• 2020

Intramural esophageal dissection is a rare disorder characterized by a separation of the mucosa and/or submucosa from deeper muscular layers of the esophagus, with or without perforation. Iatrogenic instrumentation such as endoscopy is one of the major causes of IED. We report a case of IED after endoscopy in a patient with hypopharyngeal cancer treated with concurrent chemoradiotherapy, and suggest that a history of chemoradiotherapy can be a risk factor of IED on endoscopy. In this case, chest computed tomography scans show not only typical esophageal double lumen but also eccentric esophageal wall thickening and abnormally thin the other side esophageal wall, and this CT finding may also be important to diagnose IED.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.329-336
• /
• 2004

The lock-up position of the floating ring seal affects the leakage flowrate and the stability. And it is changed depending on the operating and geometry condition. In this paper, the leakage flowrate and stability with change of the height and length were investigated by theoretical analysis and experiment. The parameter of the height and length is expressed to the b and L. The decreasing of the b resulted in the increasing of equivalent whirl frequency ratio in the experimental result at the low speed and high pressure not such as theoretical analysis. As the L increased the leakage flowrate decreased and stiffness and direct damping coefficient increased in the experimental result. That was similar to the theoretical analysis.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권3호
• /
• pp.212-222
• /
• 1998

In several structural problems, the low concrete strength of compression members has the severest influence on the structural safety. However, the repairing and strengthening techniques for compression members are not established and evaluated. This study aimed to develop and evaluate the rehabilitation techniques to obtain proper structural strength of wall with low concrete strength. The specimens with low strength of concrete were retrofitted with commonly using section increase method and epoxy bonded glass fiber techniques. The tests were executed to failure under concentric and eccentric loads. In this paper, the structural behavior and failure modes were investigated to evaluate the strengthening effects of walls subjected to compression and out-of-plane bending.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.82-88
• /
• 2008

Conventional aspherical lens polishing methods by the small tool polishing use aspherical profile and the trajectory of the polishing tool is also controlled. In this paper, new full contact polishing mechanism is suggested to polish aspherical glass lens mold by both airbag polishing tool and eccentric motion. Full contact concept by airbag polishing tool and no position control make the easy polishing setup and do not need aspherical design profile. An aspherical lens polishing machine was made for this study and a verification experiment was performed for surface roughness improvements.

• Steel and Composite Structures
• /
• 제3권1호
• /
• pp.65-73
• /
• 2003

A higher level of engineering standard in the field of construction, is the use of prestressing in building structures. The concept of prestressing steel structures has only recently been widely considered, despite a long and successful history of prestressing concrete members. Several analytical studies of prestressed steel girders were reported in literatures, but much of the work was not studied with reference to the optimal design and behaviour of the prestressed steel plate girder. A plate girder prestressed eccentrically, will behave as a beam-column, which is subjected to axial compression and bending moment which will cause the beam to buckle out. The study of buckling of the prestressed steel plate girder is necessary for stability criteria. This paper deals with the stability of prestressed steel plate girder using concept of "Vlasov's Circle of Stability" under eccentric prestressing force.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.189-196
• /
• 2002

According to the Korean Design Code for port and harbor facilaties, bearing capacity of rubble mound under eccentric and inclined load is calculated by the simplified Bishop method, and strength parameters are recommended to be c=0.2kg/$\textrm{cm}^2$ and ø=35$^{\circ}$for standard rubble if the compressive strength of parent rock is greater than 300kg/$\textrm{cm}^2$, quoting from research results by Jun-ichi Mizukami(1991), But this facts have never been certified in Korea because there was not large-scale triaxial test apparatus until 2000 in Korea. Firstly in Korea, the large-scale triaxial test (sample diameter, 30cm and height, 60cm) on the rubble originated from porous basalt rock in North-Cheju was accomplished. Then strength parameters for basalt rubble produced in North-Cheju are recommended to be c=0.3kg/$\textrm{cm}^2$ and ø=36$^{\circ}$if the compressive strength of parent rock is greater than 400kg/$\textrm{cm}^2$.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.82-87
• /
• 1997

Large dynamic loads act on the rotor in rotary compressors. There are unbalance forces due to eccentric parts and gas forces induced by the pressure difference between compression and suction gases. Rotor-journal bearing system is nonlinear since the stiffness and damping coefficients of the lubricating oil film are not constant in the bearings. The system is considered as a coupled problem of flexible rotor and the journal bearings. Bearing reaction force is calculated from pressure of oil film using Reynolds equations in journal bearings. Pressure distribution in journal bearing is analyzed by finite difference method. The dynamic response of rotor and bearing characteristic are discussed when rotary compressor has a relative misalignment.