• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.1
• /
• pp.63-71
• /
• 2017

During the sea trial test, we discovered EMI(Electromagnetic Interference) between MIL-SATCOM parabolic antenna and ES(Electronic Warfare Support) omni antenna. Emitted side lobe of CW(Continuous Wave) from MIL-SATCOM raises the threshold level of ES omni antenna. Therefore detection rate of ES is decreased. To solve this problem, the path of side lobe of CW from MIL-SATCOM should be blocked using EMI shield. This paper presents the method how to calculate the size of EMI shield, material, and optimized deployment. The test of the EMI shield effect was performed on a surface ship. After installing EMI shield, EMI has been decreased significantly. This paper will provide a method how to design EMI shield and a way to verify the result.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.1
• /
• pp.48-65
• /
• 1995

This paper deals with the analysis of the unintentional radiation from the TDX-1B subscriber Board. According to the demand of digital systems and developement of high speed switching devices, electro- magnetic noise intensity and it's bandwidth occupancy in spectrum are increasing and so there is a serious possibility causing the various EMI phenomena. More accurate radiation model was established by using the Finite Difference Time Domain (FDTD) analysis, and the EMI probabilistic analysis of the digital switching system was performed. For validating the proposed model and its calculated results, on-promises test was performed and compared with the calculated results. These results may be applicable to be used for EMI model in large digital system, and prediction of EMI effect from a large digital system, and the EMI control design when designing digital system to meet inter- national EMI regulation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.79-83
• /
• 2018

An accurate method to measure shielding effectiveness(SE) of EMI spray coating film is presented. After high frequency simulating, Circular coaxial standard test fixture is fabricated. A sample of EMI spray coating film was fabricated for insertion into a circular coaxial standard test fixture. The measuring instrument used an Agilent 8722ES vector network analyzer for the SE measurement. The exact SE of copper and silver mixed spray coating sample was measured by the composition of the measuring instrument and the measuring sample. The SE of copper sample was measured at 70 dB and the SE of copper and silver mixed spray coating sample was measured at 60 dB. As a result of the measurement, the reliability of the circular coaxial standard test fixture was confirmed.

• Smart Structures and Systems
• /
• v.17 no.1
• /
• pp.123-134
• /
• 2016

The evolution of the electro-mechanical impedance (EMI) of a piezoelectricity (PZT) sensor was investigated to determine the setting times of cement paste in this study. The PZT sensor coated with non-conductive acrylic resin was embedded in fresh cement paste and the EMI signatures were continuously monitored. Vicat needle test and semi-adiabatic calorimetry test were also conducted to validate the EMI sensing technique. Significant changes in the EMI resonance peak magnitude and frequency during the setting period were observed and the setting times determined by EMI sensing technique were relevant to those measured by Vicat needle test and semi-adiabatic calorimetry test.

• Journal of the Korea Society for Simulation
• /
• v.10 no.4
• /
• pp.21-30
• /
• 2001

In this paper, EMI measurement, the STGU simulation being conducted, filter design, its characteristics, and its implementation to the PCB, and finally test results are discussed. When the low pass filter was implemented within the STGU, the power of EMI decreased more than 20dBm. Finally, when TE and MTIE, two important quality measure in synchronous reference clock, was assessed, ITU-T G813 requirement was satisfied. EMI(Electromagnetic Interface) is a measure of electomagnetic radiation from equipment in the range of 10KHz to 3GHz, and can cause unexpected reactions of electronics/electrical equipment. In this study, for safe and stable communication operation, a STGU (System Timing Generation Unit), which is a 2.5G SDH System and a major EMI source, was employed to simulate electromagnetic interface. Using Open-Site test, the power of fundamental frequency of EMI of interest and its harmonics were measured. Also, a low pass filter at cut-off frequency of 2GHz was specifically designed for this study to minimize the effect of EMI between electronic components.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.2
• /
• pp.84-89
• /
• 2007

MIL-STD-461E, EMI military standard for the equipment and subsystems, requires reception characteristic tests to verify the susceptibility of a receiver against the jntermodulation and spurious signals. Because the CS103 and CS104 of MIL-STD-461E show the test configuration of the equipment unit like a traditional receiver, it is possible to verify the susceptibility only for the reception signal through analog filters. However, at present when software programming techniques make a progress, the CS103 and CS104 tests need to evaluate the reception signal of the subsystem which includes both the digital filtering effects and analog filter characteristics. These test and evaluation techniques applied to a surveillance radar subsystem. This paper researched the EMI test methods in order to confirm feasibility of these test and evaluation techniques. Also the test results are compared and analyzed.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.2
• /
• pp.45-52
• /
• 2002

EMI(Electromagnetic Interface) is a measure of electomagnetic radiation from equipment in the range of 10KHz to 3GHz, and can cause unexpected reactions of electronics/electrical equipment. In this study, for safe and stable communication operation, a STGU(System Timing Genetation Unit), which is a 2.5Gbps SDH System and a major EMI source, was employed to simulate electromagnetic interface. In On-Site test, the power of fundamental frequency of EMI of interest and its harmonics were measured. Also, a low pass filter at cut-off frequency of 2GHz was specifically designed to minimize the effect of EMI between electronic components. When the low pass filter was implemented within the STGU, the power of EMI decreased more than 20dBm. Finally, when TIE and MTIE, two important quality measure in synchronous reference clcok, was assessed, ITU-T G8l3 requirements are satisfied.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.5
• /
• pp.389-395
• /
• 2016

The evolution of electro-mechanical impedance (EMI) of the piezoelectricity (PZT) sensor was investigated to determine the setting times of cementitious materials in this study. The PZT sensor coated with non-conductive acrylic resin was embedded in cement paste before casting and the EMI signatures were continuously measured. Vicat needle test and semi-adiabatic calorimetry test were also conducted to justify the validity of EMI senssing technique in setting monitoring of cementitious materials. The results show that significant changes in EMI resonant peak magnitude and frequency during setting process were observed, and that the setting times determined by EMI sensing technique were relevant to the setting times measured by Vicat needle test and semi-adiabatic calorimetry test.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.99-100
• /
• 2021

In this study, the setting times of concrete was evaluated using the electro-mechanical (EMI) behavior of piezoelectric sensor embedded in the concrete. Penetration resistance test was also performed to compare with EMI sensing technique. As a result, the setting times of concrete can be measured more effectively than penetration resistance test through the EMI sensing technique using the piezoelectric sensor.

• Journal of IKEEE
• /
• v.21 no.3
• /
• pp.272-275
• /
• 2017

Recently, semiconductor integration density enormously increases and its interconnection width is significantly narrowed, which leads to EMI (electromagnetic interference) problems on chip level. Chip manufacturer exploits TEM cell (transverse electromagnetic cell) to measure EMI on chip level, which requires PCB (printed circuit board) for measurement purpose. However, it is often neglected to consider that PCB patterns and other factors can affect on EMI measurement. In this paper, several test patterns are designed for different PCB design variables, and effects of PCB patterns on EMI measurement in TEM cell are analyzed. Based on these analyses, PCB design guidelines are also proposed to minimize the effects on EMI measurements.