• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.203-204
• /
• 2012

본 논문에서는 3-레벨 ANPC 방식을 적용하여 하이브리드 자동차에 장착된 IPMSM을 구동하는 인버터를 제안하였다. 3-레벨 ANPC 인버터는 전력 반도체 스위치의 열 분배에 용이하다. 또한 3-레벨 인버터의 경우 dv/dt가 작기 때문에 THD를 감소시켜 출력 필터의 부피와 EMI를 저감 시킬 수 있다. 따라서 자동차의 신뢰성과 안전성을 높일 수 있다. 제안된 논문에서는 2-레벨 인버터와 3-레벨 ANPC 인버터 출력 특성을 분석하고, 스위치 간 온도 특성 분석 및 THD를 시뮬레이션 통하여 비교하였다.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.47-53
• /
• 2003

Screen filter of PDP TV plays an important role in satisfying the EMI/EMC specifications. Two types of filters, the mesh type and the sputter type, are used in PDP TVs, and this paper presents measurement results of the shielding effectiveness (SE) in the frequency range from 50MHz to 1GHz. Two methods were used for the measurement, one using network analyzer (NA) in an open area test site(OATS), and the other using the screen room. The overall conclusion is that the shielding effectiveness of the screen filter is related to the surface resistance of the screen filter. The mesh type screen filters are superior to the sputter types in the shielding effectiveness, which is varying with the frequency.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.498-501
• /
• 2002

In the conventional PWM converter, high-frequency switching techniques was used for high-density of energy, but occurred a lot of problems such as switching losses, switching voltage/current stresses, EMI(Electromgnetic Interference) and so on. To overcome these problems, various soft switching techniques have been presented. However these techniques are focused on reducing switching losses and voltage/current stresses . The simulation and experimental results are shown that the active clamp ZVS flyback converter with the proposed RPWM(Random Pulse Width Modulation) technique reduces the conducted noise.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.173-179
• /
• 2009

This paper proposes a new three-phase diode rectifier system with a sinusoidal input current at unity power factor and a regulated and isolated output voltage at low level. The inherent natural wave-shaping capability of the reduced kVA polyphase transformer together with an active current wave-shaping technique results in a significant reduction of input and output filter requirements associated with switching ripple and EMI. The operation principles are described along with a design example and a comparative evaluation. Experimental results on a 1.5kW prototype are provided to validate the proposed concept.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.39-41
• /
• 2005

In this paper, a study on the controller for high speed PMSM (Permanent Magnet Synchro-nous Motor) is described. PMSM can be driven over 50,000 rpm because it has no brush and commutator structure. It also has less EMI noise and easy cooling structure compare to the other motors. The controller was designed to have a capability to drive 20kw, 42,000rpm high speed motor system. A senseless vector control method was studied based on d-q conversion theory to have a high driving efficiency. The control board was designed using TMS320C33 and the performance was verified by experimental results on driving the inverter and motor system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.2
• /
• pp.143-148
• /
• 2014

Conventional wireless power transfer methods based on coupled magnetic fields need a complex winding structure on the surface of the energy transfer and shows poor efficiency near metal objects due to the eddy current effect. In this study, to mitigate these problems, we investigate an electric field-coupled power transmission system, which is less prone to metal object problems and EMI. Because of the fundamental physical limit in the size of link capacitances, a half-bridge converter with an impedance matching transformer is proposed and the design procedure is derived to provide a soft-switching scheme. Hardware implementation shows that the proposed scheme with a pair of 10cm by 10cm copper plate can power a 1.4W USB FAN in a separation of 0.2mm by using insulating paper when driven by 227 kHz gate pulse.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.40-47
• /
• 2001

Optical measurement methods make it possible to detect object displacements with high resolution and noncontact measurements. Also, they are very robust against EMI noises and have long operation range. An optical triangulation sensor is one of widely used displacement measurement sensors for its sub-micron resolution, fast response, simple structure, and low cost. However. there are several errors caused by inclinations of a surface. speckle effects, power fluctuations of light sources, and noises of detectors. In this paper, in order to minimize error effects, we performed error analysis and proposed a new structure. Then, we setup a new modeling method and verify it through simulations and experiments. Based on the new model. we propose a new sensor structure and establish design criteria. Finally, we design a signal processing system to overcome a resolution-limited problem of light detectors. The resolution of the proposed system is 0.2${\mu}{\textrm}{m}$ in 5mm operating range.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.7
• /
• pp.843-850
• /
• 2003

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless plated Cu layer and polyester (PET) film, the effect of pretreatment conditions such as etching method, mixed catalyst composition were investigated. Chemical etching and plasma treatment increased surface roughness in decreasing order of Ar＞HCl＞O$_2$＞NH$_3$. However, adhesion of Cu layer on PET film increased in the following order: $O_2$＜Ar＜HCl＜NH$_3$. It indicated that appropriate surface roughness and introduction of affinitive functional group with Pd were key factors of improving adhesion of Cu layer. PET film was more finely etched by HCI tolution, resulting in an improvement in adhesion between Cu layer and PET film. Plasma treatment with NH$_3$produced nitrogen atoms on PET film, which enhances chemisorption of Pd$^{2+}$ on PET film, resulting in improved adhesion and shielding effectiveness of Cu layer deposited on the Pd catalyzed surface. Surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$; SnCl$_2$from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, adhesion and shielding effectiveness of Cu plated PET film were increased.d.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.35-41
• /
• 2020

The small tracking radar is a very important component of the wire harness design because the components are organically connected. In addition, the cable connected to the signal processing unit and the servo unit having a large number of digital signals should be prepared to prevent the CPU of the signal processing unit from malfunctioning due to electromagnetic noise. Cables for signal transmission in the ◯◯ GHz band must reflect the design of temperature, vibration, and shock. To design a wire harness in a small space, the size of the connector must be minimized. The issues to be considered are described and the design plan is presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.57-63
• /
• 2014

In this paper a bidirectional DC-DC converter is proposed for renewable energy systems, eco-friendly vehicles, energy storage systems, uninterruptible power supply(UPS) systems and battery test equipments. The two-stage bidirectional converter employing a fixed-frequency series loaded resonant converter is designed to be capable of operating under zero-current-switching turn on and turn off regardless of voltage and load variation, and hence its magnetic components and EMI filters can be optimized. And efficiencies and volumes of the two-stage bidirectional converters are compared according to configuration of isolated and non-isolated parts and a two-stage topology suitable for low voltage and high current applications is proposed. A 12kW(12V, 1000A) prototype of the proposed converter has been built and tested to verify the validity of the proposed operation.