• 센서학회지
• /
• 제15권5호
• /
• pp.334-340
• /
• 2006

A compact biosignal monitoring device was developed. Electrodes for electrocardiogram (ECG) and a LED and silicon detector for photoplethysmogram (PPG) were used. A lead II type was arranged for ECG measurement and reflected light was measured at the finger tip for PPG. A single chip microprocessor (model ADuC812, Analog Device) controlled a measurement protocol and processed measured signals. PPG and ECG had a sampling rate of 300 Hz with 8-bit resolution. The maximum power consumption was 100 mW. The microprocessor computed pulse transit time (PTT) between the R-wave of ECG and the peak of PPG. To increase the resolution of PTT, analog peak detectors obtained the peaks of ECG and PPG whose interval was calculated using an internal clock cycle of 921.6 kHz. The device was designed to be operated by 3-volt battery. Biosignals can be measured for $2{\sim}3$ days continuously without the external interruptions and data is stored to an on-board memory. Our system was successfully tested with human subjects.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.834-837
• /
• 2005

In this paper, we describe the method of non-invasive blood pressure measurement using pulse wave transit time(PWTT). PWTT is a new parameter involved with a vascular that can indicate the change of BP. PWTT is measured by continuous monitoring of ECG and pulse wave. No additional sensors or modules are required. In many cases, the change of PWTT correlates with the change of BP. We measure pulse wave using the photo plethysmograph(PPG) sensor in an earlobe and we measure ECG using the ECG monitoring device our made in the chest. The measurement device for detecting pulse wave consists of infrared LED for transmitted light illumination, pin photodiode as light detector, amplifier and filter. We composed 0.5Hz high pass, 60Hz notch and 10Hz low pass filter. ECG measurement device consists of multiplexer, amplifier, filter, micro-controller and RF module. After amplification and filtering, ECG signal and pulse wave is fed through micro-controller. We performed the initial work towards the development of ambulatory BP monitoring system using PWTT. An earlobe is suitable place to measure PPG signal without the restraint in daily work. From the results, we can know that the dependence of PWTT on BP is almost linear and it is possible to monitoring an individual BP continuously after the individual calibration.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.356-357
• /
• 2007

In this paper, we developed an integrated miniaturized device which acquires and transmits the signal of ECG an interested heartbeat and body's temperature and humidity. Using an amplifier circuit on the electrodes and the radio frequency transmission, the developed system dispenses with the use of cables among the electrodes, amplifier, and the post processing system. The sensor signals are transmitted to the RF-wireless terminal that was developed using the micro controller Aduc812, LCD, RF-module (frequency 424MHz, 9600-bps). In results, the developed system improves not only the signal-to-noise ration in dynamic ECG & and body's temperature and humidity measurement, but also the user convenience.

• 센서학회지
• /
• 제28권1호
• /
• pp.13-16
• /
• 2019

The analysis of electrocardiogram (ECG) signals facilitates the detection of various abnormal conditions of the human heart. The QRS complex is the most critical part of the ECG waveform. Further, different diseases can be identified based on the QRS complex. In this paper, a new algorithm based on the well-known Pan-Tompkins algorithm has been proposed. In the proposed scheme, the QRS complex is initially extracted by removing the background noise. Subsequently, the R-R interval and heart rate are calculated to detect whether the ECG is normal or has some abnormalities such as tachycardia and bradycardia. The accuracy of the proposed algorithm is found to be almost the same as the Pan-Tompkins algorithm and increases the R peak detection processing speed. For this work, samples are used from the MIT-BIH Arrhythmia Database, and the simulation is carried out using MATLAB 2016a.

• 한국정보통신학회논문지
• /
• 제14권5호
• /
• pp.1303-1310
• /
• 2010

최근 운전자의 건강상태 모니터링 및 졸음운전 방지를 위한 자동차용 부품관련 센서개발 및 시스템 연구들이 국내외에서 활발히 진행되고 있다. 본 논문은 이러한 운전자의 건강 상태 및 졸음운전을 점검하기 위해 체스트벨트 심전도 (ECG)와 손목착용형 산소포화도 (SpO2) 센서를 제작하여 생체신호를 측정하였으며, 측정된 심전도, 산소 포화도, 그리고 심장박동수 신호는 무선센서네트워크를 통해 수집, 전송 및 모니터링 등의 처리를 가능하게 하여 운전자에게 안전운행을 위한 정보를 제공하도록 하였다. 원격지인 서버 PC와 연결된 베이스스테이션으로 수집된 심전도와 용적맥파 신호에서 HRV (Heart Rate Variability, 심박변이도) 신호를 검출하였으며, 검출된 HRV 신호를 시간 영역과 주파수 영역에서의 해석을 통하여 운전자의 스트레스 지수 및 졸음 상태의 실시간 모니터링 및 졸음상태의 운전자에게 주의를 제공하기 위하여 알람을 제공하는 형태의 지능형 모니터링 시스템을 구현하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.545-548
• /
• 2009

최근 운전자의 건강상태 모니터링 및 졸음운전 방지를 위한 자동차용 부품관련 센서개발 및 시스템 연구들이 국내외에서 활발히 진행되고 있다. 본 논문은 이러한 운전자의 건강상태 및 졸음운전을 점검하기 위해 체스트벨트(ECG)와 손목착용형 산소포화도($SpO_2$) 센서를 제작하여 생체신호를 측정하였으며, 측정된 심전도, 산소포화도, 그리고 심장박동수 신호는 센서네트워크를 통해 수집, 전송 및 모니터링 등의 처리를 가능하게 하여 운전자에게 안전운행을 위한 정보를 제공하도록 하였다. 원격지인 서버 PC와 연결된 베이스스테이션으로 수집된 심전도와 용적맥파 신호에서 HRV(Heart Rate Variability, 심박변이도) 신호를 검출하였으며, 검출된 HRV 신호를 시간 영역과 주파수 영역에서의 해석을 통하여 운전자의 스트레스 지수 및 졸음 상태의 실시간 모니터링 및 졸음 상태의 운전자에게 주의를 제공하기 위하여 알람을 제공하는 형태의 지능형 모니터링 시스템을 구현하였다.

• 한국위성정보통신학회논문지
• /
• 제11권3호
• /
• pp.18-23
• /
• 2016

의료 센터에서 데이터 분석과 스마트폰 어플리케이션 권한을 부여함으로써 사물 인터넷 (IoT)은 환자 중심의 의료 관찰과 관리에서 대혁변을 일으킬 것이다. 네트워크 연결은 개인 의료 서비스에서 IoT 의학 장치로 부터 건강을 관찰하는 스마트폰으로부터 진료받는 사람들의 건강 정보를 모으기 위한 기본 요구사항이다. 스마트폰에 설치된 IoT 환경은 매우 효과적이고 이것은 사회 기반 시설을 필요로 하지 않는다. 본 논문은 ECG 캡처링에 영향을 주지 않기 위해 스마트폰이 개인 IoT 아키텍처를 효율적으로 사용하는 것을 보여준다. 적응 IoT 의료 장치 관문은 클라우드 구성에 관한 대용량을 가진 개인 의료 서비스에 사용된다. 이 접근법에서, 스마트폰 카메라는 개인 ECG 파형을 추출하기 위해 사용된 이미지 기술을 기반으로 하고, 그것을 IoT 아키텍처를 사용한 대용량 저장 연결에 근거한 클라우드로 보낸다. 정교해진 알고리즘은 스마트폰이나 테블릿 카메라로 부터 찍힌 얼굴이미지로 부터 효율적인 ECG 등록을 직접 가능할 수 있는 여지를 준다. 이 심도있는 기술은 아마 적절한 기능 강화들이 소개된 후에 개인 의료 서비스를 관찰하는데 있어서 특별한 가치를 가질 것이다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.489-492
• /
• 2005

Even though the blood pressure is one of the most widely used index for the healthcare monitoring of hypertensive and normotensive persons, there is no non-intrusive measurement method which is commercialized until now. Pulse Arrival Time (PAT) is known that it has close relation with the systolic blood pressure (SBP) and arterial stiffness. In this study, SBP estimation methods by non-intrusive measurement of PAT are suggested. For the unconstrained measurement of PAT, the first method used the electrically non contact electrocardiogram (ENC-ECG) technique and the reflective type of Photoplethysmography (PPG) sensor on the computer mouse. In the second method, ENC-ECG and the air pressure sensor in the seat cushion on a chair were measured. The third method used ECG electrodes and PPG sensors on the toilet seat cover. The validation and regression analysis of the relationship of PAT and SBP are summarized. These methods have considerable errors to be used for all people. But these can be applied for each subject after the parameter customization within acceptable error. So, it is feasible for suggested methods to be used for monitoring of SBP in daily life in non-intrusive way when there is personal identification system of each subject.

• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.42-45
• /
• 2015

The ability to take electrocardiographic measurements while performing our daily activities has become the people-choice for modern age vital sign sensing. Currently, wet and dry ECG electrodes are known to pose threats like inflammations, allergic reactions, and metal poisoning due to their direct skin interaction. Therefore, the main goal in this work is to implement a very small ECG sensor system with a capacitive coupling, which is able to detect electrical signals of heart at a distance without the conductive gel. The aim of this paper is to design, implement, and characterize the contactless ECG electrodes. Under a careful consideration of factors that affect a capacitive electrode functional integrity, several different sizes of ECG electrodes were designed and tested with a pilot ECG device. A very small cotton-insulated copper tape electrode ($2.324cm^2$) was finally attained that could detect and measure bioelectric signal at about 500 um of distance from the subject's chest.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.51-53
• /
• 2006

This paper proposes a portable ECG monitoring system, which integrates uptodate PDA and RF communication technology. The aim of the study is to acquire the subject's biomedical signal without any constraint. It has two types of transmission mode, which are total signal transmission mode and HR(heart rate)/SC(step count) transmission mode. In audition, wireless communication technology uses Zigbee Wireless PAN and can work in low-power mode, which is one of the advantages of ZiBbee communication technology. The developed system is composed of a transmitter and a receiver. The transmitter has three-axial acceleration sensor. ECG amplifier and Zigbee communication controller. In total signal transmission mode, it can send data 50 packets per second whose transmission speed corresponds to 300 ECG samples and 60 acceleration samples. In HR/SG transmission mode, it can calculate heart rate from EEG data with 216 samples per second and step count from acceleration data and send a packet every cardiac cycle. The receiver forwards the received data to PDA, where the data can be stored and displayed. Therefore, the developed device enables to continuous monitoring for Activities of Daily Living(ADL). Also, this method will reduce medical costs in the aged society.