• 한국건설순환자원학회논문집
• /
• 제6권3호
• /
• pp.118-125
• /
• 2011

콘크리트 내부의 공극의 크기 및 분포상태는 콘크리트의 내구성을 결정하는 요인 중 하나이며, 구조물의 성능을 판단하는데 중요한 지표로 사용된다. 최근 고유동 콘크리트(High-Fluidity Concrete 이하 HFC로 약함)에 대한 연구는 많은 시공사례와 함께 진행되고 있지만, 콘크리트의 내구성능에 영향을 미치는 공극구조에 대한 연구는 미비한 실정이다. 따라서 본 연구에서는 30 MPa 범위의 일반콘크리트(Conventional Concrete 이하 CC로 약함) 및 석회석 미분말 및 플라이 애시를 사용한 HFC를 제조하여 콘크리트의 공극구조를 비교 분석 하였다. 실험결과 30 MPa 범위의 CC 및 HFC의 평균 공극 직경은 HFC가 CC보다 작게 나타났으며, SEM 분석 결과 HFC가 CC보다 전체적으로 내부구조가 치밀한 것으로 나타났다. 이러한 결과를 통하여 HFC가 CC보다 내구성 측면에서 우수할 것으로 판단된다.

• 한국해안·해양공학회논문집
• /
• 제23권1호
• /
• pp.11-17
• /
• 2011

항만콘크리트 구조물의 내구성 저하의 중요한 요인은 염소이온침투에 의한 철근의 부식이다. 따라서, 항만콘크리트 구조물의 염소이온 깊이와 깊이별 염소이온농도를 정량적으로 파악할 수 있다면, 구조물의 잔존수명을 사전에 비교적 정확하게 평가할 수 있다. 이러한, 구조물에서의 염소이온농도를 예측하기 위해서는 모델식의 개발이 필요하고 모델식은 정확한 현장데이타를 기반으로 한다. 이에 본 연구에서는 현장 항만구조물에 대한 코어시료를 채취하고 본 시료들에 대한 염소이온침투깊이와 깊이별 염소이온농도를 측정하고자 하였다. 시료는 1차로 완도항, 마산항, 인천항에서 채취하였고, 2차로 여수항과 동해항에서 채취하였다. 수직 높이별 영향을 파악하기 위해서 대기부, 비말대, 간만대로 나뉘어 각 층별 8개의 시료를 획득하였다. 채취된 시료중에서 4개는 강도 실험을 실시하였고, 나머지 4개로 내구성 실험을 실시하였다. 2개의 시료에 대해서는 질산은 변색법을 이용하여 염소이온 침투깊이를 측정 하였다. 나머지 2개의 시료는 깊이별로 5 mm 두께의 절편을 채취하고 이를 ASTM C 114의 시험법에 따라 염화물 이온농도를 측정하였다. 측정결과를 바탕으로 지역과 수직위치에 따른 염소이온 침투의 특성을 파악하였다.

• 자원리싸이클링
• /
• 제19권4호
• /
• pp.35-40
• /
• 2010

최근에 들어 투수콘크리트의 동결융해에 대한 저항성이 저하되는 것과 줄눈부에서의 골재박리 등의 많은 문제점들이 대두되고 있다. 따라서 본 연구에서는 기존의 투수콘크리트의 내구성을 향상시키기 위한 방안으로 잔골재와 실리카흄, 고성능감수제를 사용하여 강도 및 내구성 증진 방안을 연구하였다. 주요실험인자로 실리카흄 혼입률 10%와 잔골재 혼입률(0%, 7%, 15%)을 선정하고, 압축강도와 휨강도, 투수계수 및 공극률, 동결융해시험을 수행하였다. 실험결과 강도측면에서는 잔골재 혼입률이 증가함에 따라 압축 및 휨강도는 증가하는 경향을 보였으나, 상대적으로 공극률 감소로 인한 투수성은 저하되고, 동결융해 저항성도 크게 감소하는 것으로 나타났다. 따라서 투수콘크리트에 있어서 강도증진을 위해 사용되는 잔골재는 혼입률 제한이 필요하며, 실리카흄 10%이상을 사용하는 것이 강도 및 내구성 측면에서 효율적인 대안이 될 수 있을 것으로 판단된다.

• 한국농공학회지
• /
• 제26권3호
• /
• pp.68-80
• /
• 1984

This study was attempted in order to investigate the effects of superplasticizers on fresh and hardened concrete. The experimental program included tests on the slump and slump loss, bleeding, time of set, air content, the compacting, factor Vee Dee, compressive strength, tensile and flexural strength, permeability, shrinkage and freege-thaw durability. The major conclusions that can be drawn on the study are as follows. 1. Superplasticizers were observed to have an appreciable fluidifying action in fresh concrete so that tinder appropriate conditions, they either considerably improved its workability or permitted a water reduction of at least 8-12% to be made while maintaining normal workability. 2. The bleeding ratios of base and S,P. Concrete were much lower than those of the conventional concrete. Differences between the base and S.P. Concrete were insignifician. 3. The setting time was the longest for conventionla concrete, followed by S.P. concrete and base concrete in thatorder. And AE water reduction admixtures showed an appreciable influence on the setting and hardening characteristics of concrete and prolonged the stiffening times. 4. The high initial slump values of S.P. concrete generally decreased rapidly with increased standing time. CF values showed increasing tendencies with the increase of S.P. content, and excessive addition of S.P. caused the segregation of fresh concrete, resulting in its rejection. 5. Though there was a slight increase in strength, no significant differences are observed between base and S.P. concrete in terms of the compressive, tensile and flexural strength. 6. The permeability of S.P. concrete was significantly less than that of the conventional concrete, and the shrinkage of S.P. concrete was considerably smaller than that of the conventional concrete, but there were no significant differences between base and S.P. concrete. 7. Compared to base concrete, S.P. concrete without entrained air tended to slightly increase freeze-thaw durability, and S.P. concrete with an appropriate entrained air gave satisfactory resistance to freezing and thawing.

• 한국가구학회지
• /
• 제19권6호
• /
• pp.411-419
• /
• 2008

Xylia xylocarpa is fast-growing trees that are currently planted on trial basis in Sabah, Malaysia. The wood quality of trees grown in Sabah may differ from those grown in other places due to the environmental factors. Five 9-year-old trees of each species were extracted from their respective plots at Luasong, Tawau. Wood specimens were prepared from three height levels; bottom, middle and top, at the inner and outer radial positions. The within-tree and between-tree variations of physical properties of these species were analyzed. The basic density, oven-dry density and green moisture content(MC) are 0.72g/$cm^3$, 0.78g/$cm^3$ and 49.8% respectively. The shrinkage from green to oven-dry conditions for the radial and tangential directions were 3.35% and 5.76%, respectively. The trends of within-tree variations for most properties were more consistent in radial rather than vertical direction. This suggests diameter growth to be a more important factor contributing to the variations compared to height. Samples from the outer part of the stem were found to have higher density, shrinkage and mechanical strengths. The between-trees variations of some wood properties were found to be significantly different, probably due to genetic and micro-environmental factors. Significant correlation was recorded among the physical properties of the species. The true potential of X. xylocarpa for end-uses would be enhanced by further research such as the study on properties of wood from different sites and other properties like durability, seasoning, processing and machining characteristics. The characteristics of X. xylocarpa are comparable to a number of local popular hardwood species, indicating its suitability for heavy construction uses.

• 한국농공학회지
• /
• 제20권1호
• /
• pp.4599-4613
• /
• 1978

This study was intended to investigate the effects of bituminous material content of soil-cement mixtures on their durability. For the purpose, unconfined compressive strength test, Freeze-thaw test, and wet-dry test were performed with three types of soil. Each type of soil was mixed with three levels of cement content and each soil-cement mixture was mixed with four levels of bituminous material content. For the unconfined compressive strength test, Freeze-thaw test and wet-dry test, 324, 108, and 108-specimens were prepared respectively. Unconfined compressive strength was measured at age of 7-days, 14-days and 28-days using 108-specimens in each age. The soil-cement loss rate due to freeze-thaw and wet-dry were calculated after 12 cycles of test using 108-specimens in each test. The results are summarized as follows : 1. Optimum moisture content was increased with increase of cement content, but maximum dry density was changed irregulary with increase of the cement content. 2. The unconfined compressive strength was increased with increase of cement content, bituminous material content and curing age. Cement is more effective factor than bituminous material on unconfined compressive strength of soil-cement Mixture. 3. It is estimated as the most economical cement content that the recommended cement content of A.S.T.M. because increasing rate of unconfined compressive strength at age of 28-days was low when cement content is above the recommanded cement content of A.S.T.M. among all types of soil. 4. Although a portion of cement content is substituted for bituminous material, the necessary unconfined compressive strength can be obtained. 5. The soil-cement loss was more influenced by wet-dry than Freeze-thaw 6. The bituminous material is more effective on the decrease of soil-cement loss than increase of unconfined compressive strength 7. The void ratio of soil-cement mixture was changet irregularly with increase of cement content, but that was decreased in proportion to the increase of bituminous material content. 8. The regression equation between the unconfined compressive strength and soil-cement loss rate were obtained as table 7.

• 한국산업정보학회논문지
• /
• 제23권4호
• /
• pp.107-121
• /
• 2018

본 연구는 Kano 모델이 소비자이면서 생산자인 메이커스가 사용하는 FDM 저비용 3D 프린터에 대한 제품 품질 및 품질 만족도에 미치는 영향을 조사하였습니다. 3D 프린터 제품의 품질은 제품 자체의 고유한 품질을 기반으로 기능성, 유용성, 내구성, 신뢰성 및 안전성 측면에서 분석하였습니다. 이 연구는 Kano 분석을 통하여 고객이 원하는 3D프린터의 세부 특성을 파악해보고 Timko 계수를 사용하여 메이커스가 만족하는 영향 정도를 파악하고자 하였습니다. 결과적으로 이 연구는 제품 크기, 출력 속도, 외부 충격에 대한 내구성이 매력적인 품질로 도출되었고 안전성 부분에서는 모두 일원적 품질인 것으로 나타났다. 표면 해상도를 제외한 Timko 고객 만족 지수는 Kano 모델과 동일한 결과가 도출되었다.

• 천문학회보
• /
• 제36권2호
• /
• pp.103.1-103.1
• /
• 2011

Recent observations by Hinode show weakly-attenuated coronal loop oscillations in the presence of background flow (Ofman & Wang 2008, A&A, 482, L9). We study the vertical kink oscillations in solar coronal loops, considering field aligned flows inside the loops as well as surrounding the loops environment. The two dimensional numerical model of straight slab is used to explore the excitation and attenuation of the impulsively triggered fast magnetosonic standing kink waves. A full set of time dependent ideal magnetohydrodynamics equations is solved numerically taking into account the value of flow of the order of observed flows detected by SOT/Hinode. We find that relaxing the assumption of the limited flows within the loops enhances the damping rate of the fundamental mode of the standing kink waves by 2 - 3 % as compared to flow pattern which is basically localized within the loops. We further notice that extending the flow pattern beyond the loop thickness also enhances the strength of the shock associated with slow magnetoacoustic waves, recognized as an addition feature detected in the numerical simulation. The wider out-flow pattern destroys the oscillation patterns early as compared to narrower flow pattern, in other words we can say that it affects the durability of the oscillation. However, for the typical coronal loops parameters we find that the observed durability periods of the SOT/Hinode observation can be achieved with an out-flow Gaussian patterns for which half-width is not greater than factor 2.0 of the loop-half-width. explain a possible relation between electric current structure and sigmoid observed in a preflare phase.

• 한국전산구조공학회논문집
• /
• 제17권2호
• /
• pp.131-140
• /
• 2004

철근콘크리트 구조물의 보수ㆍ보강 등의 유지관리를 위해서는 내구성과 내하성을 동시에 고려한 건전성평가의 의사결정기준이 절실히 요구된다. 본 논문은 CART-ANFIS을 사용하는 철근콘크리트 구조물에 대하여 효율적인 모델을 나타내었다. 철근콘크리트 구조물의 손상과 진단 등에 활용되어온 분류형 전문가시스템의 일종인 퍼지이론을 이용한 결정목 구조와 기존의 인공신경망을 이용한 결정목 구조의 건전성평가를 비교 분석한다. 손상된 철근콘크리트의 내구성 회복을 위한 보강설계 이론과 내하력 증가를 위한 보장설계 이론을 정립시켜 손상검출의 산정식을 유도하였다. 본 연구의 건전성 평가시스템 모델을 이용함으로서 보다 효율적인 철근콘크리트 유지관리 뿐만 아니라 생애주기비용 예측을 수행 할 수 있다.

• 패션비즈니스
• /
• 제16권6호
• /
• pp.21-35
• /
• 2012

In consideration of the injuries and deaths occurring at manufacturing sites due to the use of inappropriate work clothes or safety devices, this study aims to categorize manufacturing work processes to develop functional work clothes for heavy industries including the automobile, machine and shipbuilding industries in South Korea. Defining the features of the work environments and work postures of these industries provided for a categorization of the work processes which would enable the development of suitable work clothes for each work process' category. The results of the study based on a questionnaire survey are as follows: Work process category 1, including steel panel pressing and auto body assembly, final inspection (in automobile) and inspection (in machine), requires work clothes with upper body and arm mobility and performance to protect from the toxic fume factor. Work process category 2, consisting of welding (in automobile), cutting-and-forming (in machine) and attachment-and-construction (in shipbuilding), requires clothing elasticity, durability and heat and fire resistance. Work process category 3 comprising welding and grinding in the machine and shipbuilding industries, requires work clothes' tear resistance and elasticity, particularly for lateral bending mobility, and work clothes' sleeves' and pants' hemlines with sealed designs to defend against iron filing penetration, as well as incombustible and heat-resistant material performance. Finally, work process category 4, including painting in machine and shipbuilding, requires work clothes with waterproofing, air permeability, thermal performance, elasticity, durability and abrasion resistance.