• Current Applied Physics
• /
• 제18권12호
• /
• pp.1592-1599
• /
• 2018

The present study deals with the effect of dual cathode buffer layer (CBL) on the performance of bilayer of 4,4'-cyclohexylidenebis[N,N-bis(4-methylphenyl)benzenamine] (TAPC) and fullerene (C70)-based organic solar cell (OSC) with low donor concentration. OSC devices with CBLs have been fabricated using thermal vapor deposition technique. We report the use of lithium fluoride (LiF) and molybdenum trioxide ($MoO_3$) as CBLs. The insertion of LiF between C70 and aluminium (Al) electrode enhances the power conversion efficiency (PCE) of device from 1.89% to 2.47% but quenching of photogenerated excitons is observed at interface of C70 and LiF layers. Incorporation of $MoO_3$ between LiF and Al electrode further enhances PCE of device to 3.51%. This has also improved the material quality and device properties, by preventing the formation of gap states and diminishing exciton quenching.

• Steel and Composite Structures
• /
• 제38권2호
• /
• pp.141-150
• /
• 2021

In the present paper we have investigated the Stoneley wave propagation at the interface of two dissimilar homogeneous nonlocal magneto-thermoelastic media under the effect of hall current applied to multi-dual-phase lag heat transfer. The secular equations of Stoneley waves have been derived by using appropriate boundary conditions. The wave characteristics such as attenuation coefficients, temperature distribution and phase velocity are computed and have been depicted graphically. Effect of nonlocal parameter and hall effect are studied on the attenuation coefficient, phase velocity, temperature distribution change, stress component and displacement component. Also, some particular cases have been discussed from the present study.

• Journal of Welding and Joining
• /
• 제35권2호
• /
• pp.23-29
• /
• 2017

Mechanical properties and hardness distributions in arc brazed joints of Dual phase steel using Cu-Al insert metal were investigated. The maximum tensile shear load was 10.4kN at the highest brazing current. It was about 54% compared to tensile load of base metal. This joint efficiency is higher than that of joint of DP steel using Cu-based filler metals which are Cu-Si, Cu-Sn. Fracture positions can be divided into two types. Crack initiation commonly occurred at three point junction among upper sheet, lower sheet and the fusion zone. However crack propagations were different with increasing the brazing current. In case of the lower current, it instantaneously propagated along with the interface between fusion zone and upper base material. On the other hand, in case of higher current, a crack propagation occurred through fusion zone. When the brazing current is low (60, 70A), the interface shape is flat type. However the interface shape is rough type, when the brazing current is high (80A). It is thought that the interface shapes were the reason why the crack propagations were different with brazing current. The interface was the intermetallic compounds which consisted of $(Fe,Al)_{0.85}Cu_{0.15}$ IMC formed by crystallization at $1200^{\circ}C$during cooling. Therefore the maximum tensile shear load and the fracture behavior were determined by a interface shape and effective sheet thickness of the fracture position.

• 한국정보통신학회논문지
• /
• 제14권4호
• /
• pp.1005-1014
• /
• 2010

다중인터페이스, 다중채널 2.4GHz 능동형 RFID시스템에서 리더가 태그들을 수집할 때, 특정 인터페이스로 태그가 집중화되는 문제가 발생한다. 이러한 문제를 해결하기 위해 인터페이스 간 부하 분산 프로토콜인 LP-결합과 AP-균형 프로토콜을 설계하고 시뮬레이션을 통하여 성능의 우수성을 보였다. 설계된 프로토콜들을 펌웨어레벨의 하드웨어에서 구현하기에는 세 가지 문제를 가진다. 첫째, 태그가 랜덤하게 리더의 채널을 선택하고, 리더가 태그의 채널을 변경시킬 수 있는 방법이 필요하다. 둘째, 리더와 태그 간 동기 문제이다. 셋째, 하나의 MCU가 2개의 인터페이스를 동시에 동작시키는 문제이다. 이 같은 문제를 해결하기위해 태그 채널 변경을 위한 메시지 설계 및 태그 채널 변경 방법과 리더와 태그 간 동기를 맞추기 위한 프로토콜을 구현했다. 그리고 실험을 통해 프로토콜의 성능을 비교 분석 하였다. LP윈도우크기가 같을 경우, 부하분산을 통해 충돌 확률을 낮게 하는 LP-결합, AP-균형의 성능이 단일인터페이스보다 우수했다.

• ETRI Journal
• /
• 제30권1호
• /
• pp.141-151
• /
• 2008

In this paper, we introduce a new verification platform with ARM- and DSP-based multiprocessor architecture. Its simple communication interface with a crossbar switch architecture is suitable for a heterogeneous multiprocessor platform. The platform is used to verify the function and performance of a DVB-T baseband receiver using hardware and software partitioning techniques with a seamless hardware/software co-verification tool. We present a dual-processor platform with an ARM926 and a Teak DSP, but it cannot satisfy the standard specification of EN 300 744 of DVB-T ETSI. Therefore, we propose a new multiprocessor strategy with an ARM926 and three Teak DSPs synchronized at 166 MHz to satisfy the required specification of DVB-T.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1500-1511
• /
• 2004

In this paper, the anti-plane transient response of a central crack normal to the interface between a piezoelectric ceramics and two same elastic materials is considered. The assumed crack surfaces are permeable. By virtue of integral transform methods, the electro elastic mixed boundary problems are formulated as two set of dual integral equations, which, in turn, are reduced to a Fredholm integral equation of the second kind in the Laplace transform domain. Time domain solutions are obtained by inverting Laplace domain solutions using a numerical scheme. Numerical values on the quasi-static stress intensity factor and the dynamic energy release rate are presented to show the dependences upon the geometry, material combination, electromechanical coupling coefficient and electric field.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2009년도 정보 및 제어 심포지움 논문집
• /
• pp.246-248
• /
• 2009

In this paper, we will describe architecture and key characteristic for the DHS which is used in COMS. DHS is implemented in the fully redundant SCU, the dual redundant MIL-STD-1553B system bus, the payload interface units(MPIU and MI2U), the redundant ADE. the SCU interface with the other main digital units of the spacecraft through the MIL-STD-1553B.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.59-64
• /
• 2008

Spindle units of machine tool are very important part in the manufacturing area. Recently high speed machining has become the main issue of metal cutting. To develop high speed machine tools, a lot of studies have been carried out for high speed spindle. Due to increase of the rotational speed of the spindle, there has been renewal of interest in tooling system of high speed spindle. This paper concerns the static stiffness in the main spindle interface according to variation of clamping force, rotational speed and tool holder shank. Finite element analysis is performed by using a commercial code ANSYS workbench. From the results, it has been shown that the geometry of tool holder shank is mostly influence on the variation of the static stiffness in the main spindle interface.

• 전자공학회논문지B
• /
• 제32B권9호
• /
• pp.1162-1170
• /
• 1995

In this paper, we present a message transfer scheme for efficient message passing in the hierarchically structured multiprocessor computer SPAX(Scalable Parallel Architecture computer based on X-bar network). The message transfer scheme provides interface not only with operating system but also with end users. In order to transfer two types of control message and data message efficiently, it supports both of memory-mapped transfer and DMA-based transfer. Dual-port RAMs are used as message buffers, and control and status registers provide efficient programming interface. Interlaced parity scheme is adopted for error control. If any error is detected at receiving node, errored packet is resent by sender according to retry mechanism. In conjunction with retry mechanism, watchdog timers are used to protect infinite waiting and repeated retry. The proposed message transfer scheme can be applied to input/output nodes and communication connection nodes as well as processing nodes in the SPAX.

• 산업공학
• /
• 제8권3호
• /
• pp.11-23
• /
• 1995

During the past few years, the productivity has been considered as one of the most important aims in developing softwares. Many practitioners and theorists are trying reuse ready made codes to increase the productivity of software development and the quality of their products. This paper introduces our experiences in developing a highly reusable class library and its reusing environment for building a database interface application. And the concepts, Structured Multi-Library and Dual Views of Class Inheritance, are also suggested, which consist our main conceptual framework in our work. Details in implementation are discussed in brief at the end.