• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.830-838
• /
• 2003

In this paper, TX/RX dual operation microstrip single antenna for satellite communication is designed, analyzed, fabricated and measured. TX/RX frequency ranges are 14.0∼l4.5 GHz, 11.7∼12.75 GHz in respectively and vertical and horizontal polarizations are used for TX and RX. This antenna uses microstrip direct feeding for RX and aperture coupled strip-line feeding for TX and accommodates stacked elements for a high directivity and wide impedance bandwidth. In an analysis of single element, FDTD and MOM was compared and FDTD analysis was more accurate because of the consideration of finite structure and imperfect two ground planes. The proposed structure facilitates generally to an extension of two dimensional array and lower an unwanted radiation by strip-line feed in TX. TX/RX 8${\times}$4 array has a return loss below -10 dB, -14 dB in TX, RX respectively and a gain ranging from 19.1∼20.7 dB in TX, 21.2∼21.8 dB in RX which has a radiation efficiency of 43∼5l %, 52∼57 %.

• Journal of Advanced Navigation Technology
• /
• v.22 no.4
• /
• pp.336-341
• /
• 2018

In this paper, we designed and implemented an ultra wideband (UWB) antenna with 5G mobile communication and WLAN bands rejection characteristics. The proposed antenna consists of a planar radiation patch with two slots, parasitic elements on both sides of the strip line and ground plane on back side. The upper n-type slot contributes for 5G mobile communication band (3.42~3.70 GHz) rejection and the lower n-type slot contributes for wireless local area network (WLAN) band (5.15~5.825 GHz) rejection. Parasitic elements were used in order to satisfy the voltage standing wave ratio (VSWR) less than or equal to 2.0 for UWB band (3.10~10.60 GHz) except two rejection bands. The Ansoft's high frequency structure simulator (HFSS) was used for antenna design and simulations. The simulated antenna showed dual rejection bands of 3.36~3.71 GHz and 5.13 ~ 5.92 GHz in UWB band, and measured result for the implemented antenna showed dual rejection bands of 3.40~3.72 GHz and 5.08~5.858 GHz. Simulated and measured VSWRs are less than or equal to 2.0 for all UWB band except dual rejection bands.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.315-316
• /
• 2008

본 논문은 송전선로 감시 시스템에 관한 것으로, Koinonia V2.0 무선 모뎀을 활용한 Dual Channel Repeater를 이용해서 송전탑에 장착된 센서들로부터 수집한 데이터를 모니터링 서버까지 전달하는 무선 릴레이 시스템에 관한 연구이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.360-361
• /
• 2006

This paper describes a wire and wireless network sensor for temperature and humidity measurements. The network sensor comprises PLC(Power Line Communication) and RF transmitter(433MHz) for acquiring an internal (on-board) sensor signal, and measured data is transmitted to a main processing unit. The network sensor module is consist of MEMS sensor, 10-bit A/D converter, pre-amp., gain-amp., ADUC812 one chip processor and PLC/RF transmitting unit. The temperature and humidity sensor is based on MEMS piezoelectric membrane structure and is implemented by using dual function sensor for smart home and smart building.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.5
• /
• pp.808-811
• /
• 2022

In this paper, a wide-range microphone system for lectures using dual 3D sensors is proposed. A previous work using a single sensor had lowering the detecting threshold to support wide-area. However it was found that an error occurred when lecturer wears clothes with low reflectivity or has small body size. When multiple sensors are used to expand the coverage it could be cause various problems. Each sensor could show different distance to the same target. We derive the rotation angle and and compensate for lecturing microphone system using sensors on the line. The proposed method shows a little improvement in performance by about 1dB compared to the previous works but the performance is uniform in all areas regardless of reflectivity.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.1
• /
• pp.1196-1204
• /
• 2001

In this paper, a new architecture of operating software associated with the component-based method is proposed. The proposed architecture comprises 문 execution module and a decision-making module. In order to make effective development and maintenance, the execution module is divided into three components. The components are referred to as Symbol, Gateway, and Control, respectively: The symbol component is for the GUI environments and the standard interfaces; the gateway component is for the network communication and the structure of asynchronous processes; the control component is for the asynchronous processing and machine setting or operations. In order to verify the proposed architecture, and off-line version of operating software is made, and its steps are as follows; I) Make virtual execution modules for the manufacturing devices such as dual-arm robot, handling robot, CNC, and sensor; ii) Make decision-making module; iii) Integrate the modules and GUI using a well-known development tools such as Microsofts Visual Basic; iv) Execute the overall operating software to validate the proposed architecture. The proposed software architecture in this paper has the advantages such as independent development of each module, easy development of network communication, and distributed processing of resources, and so on.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.806-812
• /
• 2009

In this paper, the omnidirectional circularly polarized(CP) antenna using arc-shaped mushroom structure with curved branch is proposed. To obtain a vertical polarization and an omnidirectional radiation pattern, the CP antenna uses zeroth-order resonance(ZOR) mode of composite right and left handed(CRLH) transmission line. The horizontal polarization is achieved by the curved branches. Also, the spacing between curved branch and arc-shaped mushroom structure gives the $90^{\circ}$ phase difference between vortical and horizontal polarization. The proposed antenna, therefore, has an omnidirectional CP radiation pattern In the azimuthal plane. The electrical size of the proposed antenna is reduced by 38%, compared with that of the previously presented omnidirectional CP antenna. In addition, the CP antenna is simply designed without $90^{\circ}$ phase shifter and dual feed line. The proposed antenna uses a Bazooka balun for good impedance matching and radiation pattern. To improve 3 dB axial ratio in XY plane, the designed antenna is optimized. After optimization, the measured 3 dB axial ratio in XY plane is observed in $86{\sim}282^{\circ}$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.252-264
• /
• 2023

This paper proposes a design of a dual-band band-pass filter that integrates a λg/2 open SIR structure, a transmission line, and a fork-type structure with symmetric and asymmetric open stubs. To obtain the dual-band effect, the proposed filter uses the SIR structure and adjusts the impedance ratio of the SIR structure. Therefore, the position of the harmonics of the filter is shifted through the adjustment of the impedance ratio, and this can obtain a double-band effect. In order to obtain the dual-band characteristics, the dual-band effect is obtained by inserting a open stub between the SIR structures with the SIR structure divided in half. In addition, the second frequency response is obtained by adjusting the length of the open symmetrical stub in the fork-shaped structure. The asymmetrical open stub in the fork form achieves optimum bandwidth by adjusting the length. Therefore, the first center frequency of the proposed band-pass filter is 5.896 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.13 dB and 33.6 dB. The second center frequency is 5.906 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.15 dB and 19.8 dB. The reason is that when the impedance ratio (Δ) is higher than 1, the position of the harmonic is shifted to a lower frequency band. However, if the impedance ratio (Δ) is lowered by one step, the position of harmonics will move to a higher frequency band. The function of the filter designed using these characteristics can be obtained from the measurement result. The proposed band-pass filter has no coupling loss and no via energy concentration loss because there is no coupling structure of input/output and no via hole. Therefore, system integration is possible due to its excellent performance, and it is expected that dedicated short-range communication (DSRC) system applications used in traffic communication systems will be possible.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.35-40
• /
• 2022

This paper proposes an antenna that is located outside the PCB substrate of an electronic product to enable wireless communication in the ISM band. The PCB designed the T-shaped OPEN-STUB power supply line to be miniaturized so that it does not interfere with parts or interfere with design. The characteristics of the antenna were confirmed in the 2.4GHz and 5.8GHz bands using a T-shaped stub feeder and a spiral structure. The size of the antenna is 5mm in width × 6.5mm in length, and the thickness of the PCB is 1.2T. As a result of measurement of the manufactured antenna, it was possible to obtain a return loss of -10dB or more at 2.4GHz and 5.8GHz. In the E-plane, the gain was -4.45 dBi, and in the H-plane, the gain was -1.05 dBi. Therefore, the proposed small antenna for wireless communication showed excellent performance.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.3
• /
• pp.163-168
• /
• 2015

In this paper, 433/865MHz dual band antenna is proposed by using IFA structure of a PCB antenna, the performance was improved by changing of the space between the feed point and short strip, varying the gap between the radiator and the ground plane and adding the branch line in the proposed antenna. To confirm the characteristics of the antenna parameters, HFSS from ANSYS Inc. was used for the analysis. RFID frequency band of ISO-18000-7 is 433MHz and EU-RFID frequency band of ISO-18000-6 is from 865.5 to 867.5MHz. Each of the 433/865MHz bandwidth of the proposed antenna is 5.2MHz and 18.2MHz. The maximum 433MHz antenna gain is -5.74dBi, the maximum 865MHz antenna gain is -3.36dBi. The Jig size of the proposed antenna is $60{\times}44{\times}1mm$ and the size of the antenna area $44{\times}21mm$. The results proved the possibility of the practical use on 433/865MHz by using the IFA structure that came from comparing and analyzing the measured and simulated data of the antenna.