• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.116-126
• /
• 2008

This paper describes the Dual-band WLAN transmitter with 2.4[GHz], 5[GHz]. Dual-band WLAN transmitter was designed at 2.4[GHz] and 5[GHz]. The Dual-band WLAN transmitter has a amplifier which operate at 2.4[GHz] and 5[GHz] frequency and two VCO(Voltage Controlled Oscillator) or VCO has a wide scope of frequency. these problem cause a size and a power consumption, The Dual-band WLAN transmitter module was proposed to solve these. the transmitter was designed to get output signals of IEEE 802.11a's 5.8[GHz] band signal using frequency multiplication way or to act a amplifier about the 2.4[GHz] band signal of IEEE 802.11b/g, according to inputed frequency and bias voltage that a eve using single transmission block. The output spectrum get the improved specification of ACPR of 4[dB], 6[dB], 16[dB] at +11[MHz], +20[MHz], +30[MHz] offset of center frequency compared to no linearization, was satisfied to transmit spectrum mask of IEEE 802.11a wireless Lan.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.213-217
• /
• 2012

In this paper, we design dual-band microstrip antenna for IEEE 802.16e mobile WiMAX standard IEEE 802.11 WLAN band at the same time. To solve interference at the desired operating frequency band, impedance matching is improved and simple production method showed the characteristics of the omni-directional and compact size. The proposed structure is considered to bring the effect of the installation costs, and show the antenna for dual-band communication.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.1
• /
• pp.103-107
• /
• 2009

In this paper, we designed and implemented a dual band chip antenna for WLAN, which contains within the small LAN card contrary to the enternal AP(Access Point) antenna. Limiting about the antenna size, we used dielectrics of high permittivity. Totally considering problems of demand-supply, price and characteristics, we used that relative dielectrics of ceramic is 9.8 and the thickness is 3.5mm and 5mm. Ceramic antenna can be used not only triple mode of IEEE 802.11.a,g and b but also broadband. The frequency bands have wideband characteristics of 2.4~2.5GHz and 4.9~5.85GHz and relatively constant performance.

• Journal of KIISE:Information Networking
• /
• v.32 no.5
• /
• pp.633-640
• /
• 2005

This paper proposes and analyzes a message scheduling scheme and corresponding bandwidth allocation method for the hard real-time communication on dual standard 802.11 Wireless LANs. By making the superframeof one network precede that of the other by half, the dual network architecture can minimize the effect of deferred beacon and reduce the worst case waiting timeby half. The effect of deferred beacon is formalized and directly considered to decide the polling schedule of PCF phase. Simulation results executed via ns-2 show that the proposed scheme can improve the schedulability by 3$36\%$ for real-time messages and give $9\%$ more bandwidth to non-real-time messages for the given stream sets, compared with the network whose bandwidth is just doubled with the same MAC.

• Journal of electromagnetic engineering and science
• /
• v.4 no.3
• /
• pp.124-127
• /
• 2004

A novel printed inverted-F antenna for dual-band WLAN is presented. The proposed design is based on the folded quarter-wave antennas, which have a conductor plate having two arms. An extremely thin prototype antenna is fabricated according to the simulation result. The obtained antenna can perform in IEEE802.11a, b(2.4～2.484 GHz and 5.15～5.35 GHz bands) and be adopted for laptop applications. All the measurements are performed in the actual test fixture.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.814-820
• /
• 2015

In this paper, A high selective dual-band bandpass filter was proposed using a dual-mode ring resonator with two short-circuited stubs. For dual-mode resonance, the ring resonator is directly connected with non-orthogonal feed-lines via coupling capacitors. Two short-circuited stubs which are unequal lengths are simultaneously placed at two corners along the two symmetry plane of the ring resonator in order to obtain dual-band responses. Because the feeding angle perturbated ring resonator of the proposed dual-band bandpass filter has the symmetrical structure, Even/Odd mode analysis can be well applied to extract the scattering parameters and transmission zero frequencies. The proposed dual-band bandpass filter was designed and fabricated for WLAN(Wireless Local Area Network) application of IEEE 802.11n standard. The measured results showed a good agreement with the simulation results, and it should be well applied not only for WLAN applications but also for any other communication systems.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.547-551
• /
• 2010

In this paper, Double rectangular patch with 4-bridges is investigated for solution of IEEE 802.11b/g(2.4GHz) and 802.11a(5.7GHz). Rectangular patch for 5.7GHz frequency band is printed on the PCB substrate and connected to another rectangular patch for 2.4GHz frequency band with 4-bridges to obtain dual band operation in a antenna element. The proposed antenna has a low profile and is fed by $50{\Omega}$ coaxial line. The dielectric constant of the designed antenna substrate is 3.27. Two rectangular patches have each resonance frequencies that are 2.4GHz and 5.7GHz. A dual-band characteristic is shown as connecting two rectangular patch using four bridges. Also, the proposed antenna is shown input return loss that is below -10dB at 2.4GHz and 5.7GHz of WLAN(Wireless LAN).

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.168-175
• /
• 2013

This paper presents compact dual-band WLAN filter and filter module. They were developed by embedding all of the passive lumped elements into a LTCC substrate. In order to reduce the size/volume of the filter and avoid EM parasitic couplings between the passive elements, the proposed filter was designed using a 3rd order Chebyshev circuit topology and J-inverter transformation technology. The 3rd order Chebyshev bandpass filter was firstly designed for the band-selection of the 802.11b and was then transformed using finite transmission zeros technologies. Finally, the dual-band filter was realized by adding two notch resonators to the 802.11b filter circuit for the band-selection of the 802.11a/g. The maximum insertion losses in the lower and higher passbands were better than 2.0 and 1.3 dB with minimum return losses of 15 and 14 dB, respectively. Furthermore, the filter was integrated with a diplexer to clearly split the signals between 2 and 5 GHz. The maximum insertion and minimum return losses of the fabricated module were 2.2 and 14 dB at 2.4 - 2.5 GHz, and 1.6 and 19 dB at 5.15 - 5.85 GHz, respectively. The overall volume of the fabricated filter was $2.7{\times}2.3{\times}0.59mm^3$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1702-1707
• /
• 2010

As quantities of the data that transmitting by the wireless are more increased, the interest and application are extending about 802.11n that uses by combination two existing 20MHz wireless LAN Channel. 802.11n use dual band of 2.4GHz band and 5.8GHz. So this is expected in mass wireless transmission method because of interference evasion effect in compliance with the radio communication of existing 2GHz neighborhood band. Like this 802.11n uses the radio as well and transmits information there is not only a possibility of undergoing an influence in radio wave environment of circumference. Specially the interior environment and outdoor environment is a possibility of saying that will be defined with each other different modeling as affects in radio communication is different. In this paper, we'll compare the influence to RF feature (802.11n) by (Indoor/Outdoor) environment difference through compared with 802.11n RF feature and Network feature in (Indoor/Outdoor) environment and also examine the correlation between RF feature and Network feature.

• Journal of electromagnetic engineering and science
• /
• v.17 no.1
• /
• pp.20-28
• /
• 2017

A fully integrated dual-band CMOS power amplifier (PA) is developed for 802.11n WLAN applications using wafer-level package (WLP) technology. This paper presents a detailed design for the optimal impedance of dual-band PA (2 GHz/5 GHz PA) output transformers with low loss, which is provided by using 2:2 and 2:1 output transformers for the 2 GHz PA and the 5 GHz PA, respectively. In addition, several design issues in the dual-band PA design using WLP technology are addressed, and a design method is proposed. All considerations for the design of dual-band WLP PA are fully reflected in the design procedure. The 2 GHz WLP CMOS PA produces a saturated power of 26.3 dBm with a peak power-added efficiency (PAE) of 32.9%. The 5 GHz WLP CMOS PA produces a saturated power of 24.7 dBm with a PAE of 22.2%. The PA is tested using an 802.11n signal, which satisfies the stringent error vector magnitude (EVM) and mask requirements. It achieved an EVM of -28 dB at an output power of 19.5 dBm with a PAE of 13.1% at 2.45 GHz and an EVM of -28 dB at an output power of 18.1 dBm with a PAE of 8.9% at 5.8 GHz.