• Nuclear Engineering and Technology
• /
• v.45 no.4
• /
• pp.421-426
• /
• 2013

The need for extended storage of used nuclear fuel is increasing globally as disposition schedules for used fuel are pushed further into the future. This is creating a situation where dry storage of used fuel may need to be extended beyond normal regulatory licensing periods. While it is generally accepted that used fuel in dry storage will remain in a safe condition, there is little data that demonstrate used fuel performance in dry storage environments for long periods of time. This is especially true for high burnup used fuel. This paper discusses a technical approach that defines a process that develops the technical basis for demonstrating the safety of used fuel over extended periods of time.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.277-281
• /
• 2022

The wetting dynamics of water droplets dispensed on the surface of dry and wet hydrophilic membranes were investigated experimentally from a microscale point of view. By using a high-speed, white-beam x-ray microimaging (WXMI) synchrotron, consecutive images displaying the dynamic motions of the droplets were acquired. Through analyzing the characteristics observed, it was found that the dry hydrophilic membrane showed local hydrophobicity at a certain point during the absorption process with apparent contact angles greater than 90. While on the other hand, the apparent contact angles of a water droplet absorbing into the wet membrane remained less than 90 and showed total hydrophilicity. The observations and interpretation of characteristics that affect the contact, wetting, recoiling, and dynamic behaviors of droplets are significant for controlling liquid droplet impingement in a desired manner.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.922-925
• /
• 1999

The Silylation photo-resist etch process was tested by Enhanced-ICP dry etcher. The comparison of the two process results of micro pattern etching with 0.25${\mu}{\textrm}{m}$ CD by E-ICP and ICP reveals that E-ICP has better quality than ICP The etch rate and the microloading effect was improved in E-ICP Especially, the problem of the lateral etch was improved in E-ICP.

• Journal of Korean Neurosurgical Society
• /
• v.51 no.5
• /
• pp.247-252
• /
• 2012

Objective : The anatomical knowledge is the most important and has a direct link with success of operation in cervical spine surgery. The authors measured various cervical parameters in cadaveric dry bones and compared with previous reported results. Methods : We made 255 dry bones age from 19 to 72 years (mean, 42.3 years) that were obtained from 51 subjects in 100 subjects who donated their bodies. All measurements from C3-C7 levels were made using digital vernier calipers, standard goniometer, and self-made fix tool for two different cervical axes (canal and disc setting). We classified into 4 groups (uncinate process, vertebral body, lamina, and pedicle) and measured independently by two neurosurgeons for 28 parameters. Results : We analyzed 23970 measurements by mean value and standard deviations. In comparing with previous literatures, there are some different results. The mean values for uncinate process (UP) width ranged from 5.5 mm at C4 and 5 to 6.3 mm at C3 and C7 in men. Also, in women, the mean values for UP width ranged from 5.5 mm at C5 to 6.3 mm at C7. C7 was widest and C5 was most narrow than other levels. The antero-posterior length of UP tended to increase gradually from C3 to C6. The tip way, tip distance, and base distance of UP also showed increasing pattern from C3 to C7. Conclusion : These measurements can provide the spinal surgeons with a starting point to address bony architectures surrounding targeted soft tissues for safeguard against unintended damages during cervical operation.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.3
• /
• pp.193-199
• /
• 2016

This study is a research about performance of fireproof board using industrial waste such as oyster shell and dry process bottom ash through the heating test and conclusions were obtained as follows. Test samples show back side temperatures as follows : in $300^{\circ}C$, $103.1{\sim}125.1^{\circ}C$, in $600^{\circ}C$, $201.1{\sim}210.1^{\circ}C$, in $900^{\circ}C$, $249.2{\sim}276.9^{\circ}C$. In the test, temperature increases of specimens of fireproof board are kept at certain temperatures hence it could be concluded that the specimens withstand high temperatures. According to the test, it could be concluded that fireproof board made by smaller particles shows better performance up to $600^{\circ}C$ while at higher temperatures, fireproof board made by bigger particles shows better performance. It is estimated that fireproof board made by particles of bigger size has more pore structure and it delays heat conduction.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.8
• /
• pp.1251-1258
• /
• 2010

During the nitrogen-fixing process, ammonia ($NH_3$) is incorporated into glutamate to yield glutamine and is generally not secreted. However, in this study, $NH_3$-excreting strains of nitrogen-fixing Paenibacillus were isolated from soil. The ammonium production by the Paenibacillus strains was assayed in different experiments (dry biomass, wet biomass, cell-free extract, and cell-free extract adsorbed on nano $TiO_2$ particles) inside an innovative bioreactor containing capsules of $N_2$ and $H_2$. In addition, the effects of different $N_2$ and $H_2$ treatments on the formation of $NH_3$ were assayed. The results showed that the dry biomass of the strains produced the most $NH_3$. The dry biomass of the Paenibacillus strain E produced the most $NH_3$ at 1.50, 0.34, and 0.27 ${\mu}M$ $NH_3$/mg biomass/h in the presence of $N_2$ + $H_2$, $N_2$, and $H_2$, respectively, indicating that a combined effluent of $N_2$ and $H_2$ was vital for $NH_3$ production. Notwithstanding, a cell-free extract (CFE) adsorbed on nano $TiO_2$ particles produced the most $NH_3$ and preserved the enzyme activities for a longer period of time, where the $NH_3$ production was 2.45 ${\mu}M$/mg CFE/h over 17 h. Therefore, the present study provides a new, simple, and inexpensive method of $NH_3$ production.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2006.11a
• /
• pp.654-658
• /
• 2006

To solve some problems that reveals in the exiting stickiness problem of the housetop, the housetop finishing impact layer can be displaced by the existing concrete block. By doing in this way, this need is rising that the excess cost should be reduced and the materials should be recycled in repairing. According to the above, this study is going to suggest the basic data on building and using of the dry process method by estimating and analyzing a overall determinate quantity through the experiment on the insulation performance among the capacity items on the outside insulation waterproof dry process suggested. In addition, choosing the building method according to the use, the peculiar property and the importance of the building can be possible by analyzing the defect causes happening in the rooftop insulation and waterproof, suggesting the better method and classifying the most proper choosing methods for the need of the building according to the importance of the main factors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.459-459
• /
• 2012

Recently, the discharge of global warming gases in dry etching process of TFT-LCD display industry is a serious issue because perfluorocarbon compound (PFC) gas causes global warming effects. PFCs including CF4, C2F6, C3F8, CHF3, NF3 and SF6 are widely used as etching and cleaning gases. In particular, the SF6 gas is chemically stable compounds. However, these gases have large global warming potential (GWP100 = 24,900) and lifetime (3,200). In this work, we chose C3F6O gas which has a very low GWP (GWP100 = <100) and lifetime (< 1) as a replacement gas. This study investigated the effects of the gas flow ratio of C3F6O/O2 and process pressure in dual-frequency capacitively coupled plasma (CCP) etcher on global warming effects. Also, we compared global warming effects of C3F6O gas with those of SF6 gas during dry etching of a patterned positive type photo-resist/silicon nitride/glass substrate. The etch rate measurements and emission of by-products were analyzed by scanning electron Microscopy (SEM; HITACI, S-3500H) and Fourier transform infrared spectroscopy (FT-IR; MIDAC, I2000), respectively. Calculation of MMTCE (million metric ton carbon equivalents) based on the emitted by-products were performed during etching by controlling various process parameters. The evaluation procedure and results will be discussed in detail.

• Korean Journal of Food Science and Technology
• /
• v.22 no.6
• /
• pp.651-658
• /
• 1990

Starch phosphates were prepared by dry heating, gelatinizing method and extrusion process using sodium tripolyphosphote (STPP) as a substitution reagent and their physicochemical properities were compared. In the preparation of starch phosphate by dry heating method(DSP), the effect of reaction temperature was the most significant to the DS(Degree of substitution). In the phosphorylation reaction with gelatinized starch(GSP), the substitution ratio was increased with increasing the reaction temperature, but the increase was insignificant above $85^{\circ}C$. By extrusion with the corn starch containing 2.0% STPP at various moisture contents of 20, 25 and 30%, the DS values of extrudate(WESP) were within the range of between 0.0066 and 0.0083. The starch phosphate(DSP) products showed lowering the gelatinization temperature, increasing the clarity of the starch paste. However, WESP showed higher gelatinization temperature than that of raw starch. The starch phosphate prepared by extrusion process showed lower apparent viscosity of paste than that of the DSP at same condition. All of starch phosphates showed reducing the tendency of the paste retrogradation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.7-14
• /
• 2017

This study manufactured a minimum quantity lubrication (MQL) supply system and identified the optimal MQL machining cutting conditions for plastic mold steel (SCM440). A series of experiments were consisted of twice. Optimal cutting conditions were derived using the Taguchi method, and cutting force variance; surface roughness; tool wear; and cutting temperature in dry, wet, and MQL machining were measured experimentally for these optimal conditions. The measured results decreased from dry to wet and MQL machining, being particularly large for dry machining due to increased cutting time. Measured MQL machining metrics were similar to those for wet machining, particularly for surface roughness, which is an index of machining quality.