• 오토저널
• /
• 제10권5호
• /
• pp.61-68
• /
• 1988

This paper reports the basic performance of a naturally aspirated DI diesel engine which is used widely in industry and agriculture when vegetable oils are used as fuel substitutes. In this paper, the properties of vegetable oils as diesel fuel were investigated and the load-performance of diesel engine when vegetable oils were used, as tested compared against diesel fuel. The general objective of this investigation is to realize an efficient, clean, and low carbon deposit combustion of the vegetable oils in diesel engines, showing their feasibility as diesel fuel substitutes. The results of this experiment were as follows; (1) Compared with diesel fuel, the droplet size of vegetable oil is very large. (2) Compared with diesel fuel, rapeseed oil, palm oil, and their blend fuels offered lower smoke, lower NOx, ower engine noise, and high thermal efficiency in a D.I. diesel engine However, there were carbon deposit and piston ring sticking problems with long-term operation. (3) For ethanol-rapeseed oil blends, a 10-20% of ethanol content is recommended to enable lower BSHC and less smoke without a remarkable increase in engine noise compared with pure rapeseed oil. (4) A 10% oxygen content in the vegetable oils is contributed to reduced smoke emission.

• Archives of Pharmacal Research
• /
• 제28권12호
• /
• pp.1400-1404
• /
• 2005

The aim of the present study was to develop the aqueous parenteral formulation containing propofol using o/w microemulsion systems. Propofol itself was chosen as the oil phase and its content was fixed to 1$\%$, w/w. Pseudoternary phase diagrams were constructed to obtain the concentration range of surfactant and cosurfacatnt and the optimum ratio between them for microemulsion formation. Consequently, the suitability of the chosen microemulsion system as a parenteral formulation was evaluated from the stability and hemolysis tests on that. Among the surfactants and cosurfactants screened, the mixture of Solutol HS 15-ethyl alcohol (5/1) showed the largest o/w mocroemulsion region in the phase diagram. When 1 $\%$ (w/w) of propofol was solubilized with 8$\%$ (w/w) of Solutol $HS^{circledR}$??? 15-ethyl alcohol (5/1), the average droplet size (150 nm) and the content of propofol in the systems were not significantly changed at 40$^{circ}C$ for 8 weeks. The hemolysis test showed that this formulation was nontoxic to red blood cells. In conclusion, propofol was successfully solubilized with the o/w microemulsion systems.

• Journal of Pharmaceutical Investigation
• /
• 제35권4호
• /
• pp.233-241
• /
• 2005

Ursolic acid (UA), a bioactive triterpene acid, has been known to increase collagen content in human skin in addition to other actions such as anti-inflammatory, skin-tumor prevention and anti-invasion. However, it is poorly soluble in water. Therefore, we firstly prepared microemulsion system with benzyl alcohol, ethanol and Cremophor EL, RH 40 and Brij 35 as surfactant in order to increase solubility of UA and then prepared microemulsion was dispersed in o/w cream base for the topical delivery of UA in an effort to improve anti-wrinkle effect. The pseudo-ternary phase diagrams were developed and various microemulsion formulations were prepared using benzyl alcohol as an oil, Cremophor EL, RH 40 and Brij 35 as a surfactant. The droplet size of microemulsions was characterized by dynamic light scattering. The accumulation of VA in the skin from topical cream was evaluated in vitro using hairless mouse skins. The mean droplet size was $26.8{\pm}6.6$ nm for microemulsions II with Cremophor EL. All UA creams showed pseudoplastic flow and hysterisis loop in their rheogram, depending on the type of materials added in topical creams. The in vitro accumulation data demonstrated the UA topical cream prepared with the combination of Poloxamer 407 and Xanthan gum as a copolymer showed higher accumulation percentage than those prepared with either Poloxamer 407 or Xanthan gum. These results suggest that UA topical cream using microemulsion systems may be promising for the topical delivery of UA.

• 한국응용과학기술학회지
• /
• 제21권1호
• /
• pp.31-36
• /
• 2004

Liquid crystalline phases were formed from acylglutamate; polyglyceryl-10 myristate and glycerine mixture and they were used as a base material for preparing an O/W emulsion. When an oil phase is added into the liquid crystalline phases, it was inserted into the dispersed liquid crystal droplets rather than stayed outside the liquid crystals, which can be known by the fact that the size of liquid crystal droplets increases with the increasing oil phase content. Along with the increase in the droplet size, the complex modulus increases from 100 to 350 pascals and the loss angle decreases from 60 to 24 degrees, from which it can be known that the increase in the internal phase volume results in the increase in the elastic property of oil in liquid crystalline-phases (O/LC). When the water phase was lastly added into the O/LC phase, the emulsification occurred to form a O/W emulsion and the averaged particle size of the O/W emulsion changes from 22.5nm to 538nm with the addition of water phase. The results from the droplet size measurements and stability tests under accelerated conditions such as high temperature show that the obtained O/W emulsion is very consistent with time.

• Nuclear Engineering and Technology
• /
• 제55권8호
• /
• pp.2966-2976
• /
• 2023

A tritium breeder is a lithium-based material capable of producing tritium. Many researchers designing nuclear-fusion energy are studying tritium production using pebbles, which are solid-type breeders. The sphericity and size of the pebbles are critical in obtaining pebbles with good tritium-breeding efficiency. Furthermore, tritium-release efficiency can be increased by using pebbles with appropriate porosities. Promising raw materials for tritium-breeding materials include Li₄SiO₄ and Li₂TiO₃. Li₄SiO₄ has a higher lithium density than Li₂TiO₃ and exhibits excellent tritium-breeding efficiency. However, it has the disadvantage of being easily decomposed during the Li₄SiO₄-green-pebble sintering process because of its low structural stability at high temperatures and high lithium density. In this study, we attempted to determine the optimal conditions for manufacturing Li₄SiO₄ pebbles using the droplet-freeze-drying method. The optimal Li₄SiO₄ slurry conditions and sintering temperatures were determined. The optimal Li₄SiO₄ slurry-fabrication conditions were 3 wt% polyvinyl alcohol and 75 wt% Li₄SiO₄ based on the deionized-water weight content. The sintering temperature at which Li₄SiO₄ did not decompose and exhibited the optimum porosity of 10.8% was 900 ℃.

• Macromolecular Research
• /
• 제15권6호
• /
• pp.520-526
• /
• 2007

The effects of poly($({\varepsilon}$-caprolactone) (PCL) on poly(acrylonitrile-butadiene-styrene) (ABS) and polycarbonate (PC) blends were studied. Blends of ABS/PC (70/30, wt%) with PCL as a compatibilizer were prepared by a twin screw extruder. From the glass transition temperature $(T_g)$ results of the ABS/PC blends with PCL, the $T_g$(PC) of the ABS/PC (70/30) blends decreased with increasing PCL content. From the results of the morphology of the ABS/PC (70/30) blends with PCL, the phase separation between the ABS and PC phases became less significant after adding PCL in the ABS/PC blends. In addition, the morphological studies of the ABS/PC blends etched by NaOH indicated that the shape of the droplet was changed from regular round to irregular round by adding PCL in the ABS/PC blends. These results for the mechanical properties of the ABS/PC blends with PCL indicated that the tensile, flexural and impact strengths of the ABS/PC (70/30) blends peaked at a PCL content of 0.5 phr. From the results for the rheological properties of the ABS/PC (70/30) blends with PCL content, the storage modulus, loss modulus and complex viscosity increased at PCL content up to 5 phr. From the above results of the $T_g$, mechanical properties, morphology and complex viscosity of the ABS/PC blends with PCL, it was concluded that the compatibility was increased with PCL addition in the ABS/PC (70/30, wt%) blends and that the optimum concentration of PCL as a compatibilizer is 0.5 phr.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.60-68
• /
• 2002

Experiments have been conducted to investigate the effects of emulsified fuels on the spray characteristics and exhaust emissions in a diesel engine. Four different fuels were examined : diesel, emulsified fuels with water contents which were varied with 13, 15, and l7wt%. Characteristics of fuel spray were measured by an optical method, PLLIF(planar liquid laser induced fluorescence). Compared to diesel fuel, emulsified fuels which had relatively high kinematic viscosity showed smaller spray angle and longer spray tip penetration. The qualitative droplet distributions of emulsified fuels showed worse atomization process than that of diesel fuel. As the water contents were increased, PM and NOx could be reduced simultaneously. It was specially noted that the emulsified fuel with l7wt% water content was found to be the best in reducing rates, NOx 30% and PM 40%.

• 한국분말재료학회지
• /
• 제16권1호
• /
• pp.56-62
• /
• 2009

The degree of WC decomposition and hardness of thermally sprayed WC-Co coatings are important factors determining the wear resistance of the coatings. In order to minimize the degree of decomposition and to increase hardness, the effects of processing parameters of high velocity oxyfuel(HVOF) spraying on various characteristics of nanostructured WC-12Co coating have been evaluated by an experimental design method. The HVOF sprayed WC-12Co coatings consisted of various carbide phases including WC, $W_2C$ and $W_3Co_3C$, with a much reduced carbon content. The degree of WC decomposition and decarburization was affected by changing barrel length and spray distance. The hardness of WC-Co coatings was strongly related to droplet temperature at substrate, and increased with increasing fuel addition and/or decreasing spray distance. The effective control of processing parameters was discussed in detail for manufacturing a high performance WC-Co coating.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 추계학술대회 논문집(Proceeding of the KOSME 2000 Autumn Annual Meeting)
• /
• pp.91-98
• /
• 2000

The fuels of water-in-oil emulsion have a potential of reducing PM(Particulate Matter) and NOx emissions, and increassing combustion efficiency in the furnaces and the burners. For making the most of the beneficial of the secondary atomization due to the microexplosion, the water droplets distributed in the oil must have the optimal sizes. The purpose of this paper is to investigate the water droplet size distribution characteristics of the different types of the static mixers. For analysing the size distribution characteristics efficiently, image analysis system was constructed and an appropriate image processing algorithm was developed. Two kinds of static mixers: Kenics type and RF type, were tested. As a results, RF type static mixer shows a better characteristics in the mean drop sizes, particularly in the condition of high water content.

• Journal of Welding and Joining
• /
• 제11권1호
• /
• pp.73-79
• /
• 1993

The phenomenon of metal transfer has been investigated for different transfer modes using a digital high speed motion analyzer and an arc shadow-graphing system based on a laser source and related optical system. It was observed that the pinch instability phenomenon did not occur for the globular transfer mode, since the liquid globule was then spherical rateher than a cylindrical liquid bar. On increasing the ratio of carbon dioxide to argon, the transition current from globular to spray transfer generally increased, but it is interesting that the transition was observed to occur at the lowest current in a 5% CO$_{2}$-95% argon gas mixture. For pure carbon dioxide and helium shielding gases, the drop frequency increased slowly with increasing current. At high currents or an argon based shielding gas, the length of liquid bar decreased as the carbon dioxide content increased. The acceleration of a droplet within the arc was determined using the gas drag force theory and was found to be greater than the experimental results.