• International Journal of Naval Architecture and Ocean Engineering
• /
• v.4 no.4
• /
• pp.447-459
• /
• 2012

The present study numerically investigates the effect of the wavy leading edge on hydrodynamic characteristics for the flow of rectangular wings with the low aspect ratio of 1.5. Five different wave lengths at fixed wavy amplitude have been considered. Numerical simulations are performed at a wide range of the angle of attack ($0^{\circ}{\leq}{\alpha}{\leq}40^{\circ}$) at one Reynolds number of $10^6$. The wavy wings considered in this study did not experience enough lift drop to be defined as the stall, comparing with the smooth wing. However, in the pre-stall region, the wavy wings reveal the considerable loss of the lift, compared to the smooth wing. In the post-stall, the lift coefficients of the smooth wing and the wavy wings are not much different. The pressure coefficient, limiting streamlines and the iso-surface of the spanwise vorticity are also highlighted to examine the effect of the wave length on the flow structures.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.94-100
• /
• 2018

Generally, in a single-phase energy storage system (ESS) for households, AC ripple component with twice the fundamental frequency exists inevitably in the DC link voltage of single-phase PCS. In the grid-connected mode of a single-phase inverter, the AC ripple component in the DC link voltage causes low-order harmonics on grid-side current that deteriorates power quality on an AC grid. In this work, a control system adopting a feedforward controller is established to eliminate the AC ripple interference on the DC link side. Optimal battery nominal voltage design method is also proposed by considering the voltage loss and AC ripple voltage on DC link side in a single-phase ESS. Finally, the control system and battery nominal voltage design method are verified through simulations and experiments.

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.319-324
• /
• 2007

The structural properties of $SiO_2$ liquid at finite temperatures have been investigated by molecular dynamics (MD) simulations utilizing the Tersoff interatomic potential. During cooling process, the $SiO_2$ liquid structure quenched with a cooling rate of $1.0{\times}10^{11}K/sec$ shows the traditional properties observed in the experiments. The coordination defects of system decrease with decreasing temperature up to 17%. The $SiO_2$ glass quenched up to 1600 K contains defects consisting of the fivefold coordination of Si, and the threefold coordination of O atoms. The calculated diffusion coefficients which are calculated by monitoring. the mean-square displacement of atoms drop to almost zero below 3000 K ($<10^{-6}\;cm^2/sec$) but has a fluctuations at low temperature. The structure properties of $SiO_2$ liquid shows a significant dependence on the temperature during cooling process. Bond-angle distribution at around $120^{\circ}$ originate from the O and Si atoms consisting of the over-coordinated O atoms.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2480-2490
• /
• 1996

This paper presents a new type of hydraulic servo chllinder which is characterized by its simple construction and an ubtegrated feedback mechanism. Piston position of the cylinder is controlled by eletrical input and mechamical feedback deduced from its own structure. Hydraulic pressure in each cylinder room is controlled by a poppet valve. The poppet is activated by a solenoid and is linked to the piston. Solenoid input current pulls up the poppet, which results in pressure drop and thus piston motion. The piston motion generates pull down force on the poppet by the linkage and the motion stops at equilibrium. In that way the piston position is controlled by an expernal input current. Characteristics of the servo cylinder is verified by stability analysis, tranient vehavior and steady state positing for step input. Design parameter analyses have been executed by derivation of analytical approximate solutions and by computer simulations. A prototype hydraulic servo cylinder is developed and tested. The experimental results show successful function of the servo cylinder and consistency with the theoritical results.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.38-45
• /
• 2004

This study describes the analysis results of unsteady cavitating flows behavior inside nozzle of the prototype piezo-driven injector. This piezo-driven injector has been recognised as one of the next generation diesel injector due to a higher driven efficiency than the conventional solenoid-driven injector. The three dimensional geometry model along the central cross-section regarding of one injection hole has been used to simulate the cavitating flows for injection time by at fully transient simulation with cavitation model. The cavitation model incorporates many of the fundamental physical processes assumed to take place in cavitating flows. The simulations performed were both fully transient and 'pseudo' steady state, even if under steady state boundary conditions. We could analyze the effect the pressure drop to the sudden acceleration of fuel, which is due to the fastest response of needle, on the degree of cavitation existed in piezo-driven injector nozzle

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.1
• /
• pp.65-71
• /
• 2015

The purpose of this study is to investigate cavitating flow of the multistage centrifugal pump. Cavitation is observed in the impeller leading edge and trailing edge of the suction area. Head coefficients are measured under different flow operating conditions. The Rayleigh-Plesset cavitation model is adapted to predict the occurrence of cavitation in the pump. The two-phase gas-liquid homogeneous CFD method is used to analyze the centrifugal pump performances with two equation transport turbulence model. The simulations are carried out with three different flow coefficients such as 0.103, 0.128 and 0.154. The occurrence of cavitation described according to water vapor volume fraction. The head versus NPSH (Net Positive Suction Head) also measured using different flow coefficients. Development of cavitation in the centrifugal pump impellerI is discussed. It is showed that the simulation represents the head drop about 3%.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.10 no.2
• /
• pp.13-18
• /
• 2014

This paper proposes an optimum pipe material (PVC vs. PE) design & selection for open loop ground heat exchangers. Heat exchange efficiency and/or workability, and the need for trench insulation were investigated by comparing EWT (cooling mode) of each system. CFD simulations for the PVC and PE pipe with the same inner diameter show similar EWT. This is because the PVC pipe has a small thickness but a low thermal conductivity as compared to the PE pipe, and thus these two properties tend to offset each other. However, a hypothetically insulated pipe led to a meaningful drop of EWT. This means pipe insulation is of importance in performance of ground heat exchangers. From analyzing climate data and system operation, it is not advantageous to insulate trench pipes due to construction difficulties and ground temperature characteristics that are seasonally varied.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.708-717
• /
• 2015

This paper proposes a new reduction scheme of circulating current when two units of BESS (Battery Energy Storage System) are operated in parallel with conventional droop control. In case of using conventional droop, the terminal voltage of each BESS are not equal due to the unequal line impedance, which causes the circulating current. The operation performance of BESS is critically dependant on the circulating current because it increases system losses which causes the increasement of required system rating. This paper introduces a new reduction scheme of circulating current in which the terminal voltage difference of each BESS is compensated by adding feed-forward path of line voltage drop to the droop control. The feasibility of proposed scheme was first verified by computer simulations with PSCAD/EMTDC software. After then a hardware prototype with 5kW rating was built in the lab and many experiments were carried out. The experimental results were compared with the simulation results to confirm the feasibility of proposed scheme. Two parallel operating BESS with proposed scheme shows more accurate performance to suppress the circulating current than those with the conventional droop control.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5997-6003
• /
• 2011

To increase the driving distance of a natural gas vehicle, the high pressure of fuel charge is necessary and the development of the device reducing the pressure to suitable pressure for fuel of high pressure. In this study, Pressure characteristics at the pressure regulator, which is very important for gas supply systems for vehicles, are investigated. Numerical simulations are carried out to quantify pressures at regulators for several flow rates and to investigate pressure drop, hysteresis losses at some parts in the pressure regulator. Moreover, this paper presents a new kind of hydraulic simulation which is composed of CNG regulator. Lastly, experiments are carried out to verify the effectiveness of the prosed mathematical simulation with various regulator components as in real working condition.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.4
• /
• pp.820-828
• /
• 2016

The sizable electrical load of plug-in electric vehicles may cause a severe low-voltage problem in a distribution network. The voltage drop in a distribution network can be mitigated by limiting the power consumption of a charging station. Then, the charging station operator needs a method for appropriately distributing the restricted power to all plug-in electric vehicles. The existing approaches have practical limitation in terms of the availability of future information and the execution time. Therefore, this study suggests a heuristic method based on priority indexes for fairly distributing the constrained power to all plug-in electric vehicles. In the proposed method, PEVs are ranked using the priority index, which is determined in real time, such that a near-optimal solution can be obtained within a short computation time. Simulations demonstrate that the proposed method is effective in implementation, although its performance is slightly worse than that of the optimal case.