• 한국산학기술학회논문지
• /
• 제10권9호
• /
• pp.2210-2220
• /
• 2009

대형 특수차량용 독립현가형 액슬은 극소수 전문업체에서 생산되며 설계, 제작, 시험평가 등 세부기술은 제공되지 않고 있다. 또한 액슬 제작을 위한 설계기준 설정에는 시작품을 실제 차량에 탑재하여 수년 이상 소요되는 내구성 시험이 필수적이다. 본 연구는 독립현가형 액슬의 핵심부품인 스루드라이브를 역설계방법으로 개발하였으며 개발목표 달성 확인에 필요한 시험평가기준을 제안하였다. 또한 CAD/CAE 도구를 사용하여 제품을 설계하고 설계검증을 거쳐 시제품을 제작하였다. 본 연구에 적용된 개발절차 및 방법은 차량의 동력전달계통 개발에 유용할 것이다.

• 드라이브 ㆍ 컨트롤
• /
• 제20권3호
• /
• pp.9-14
• /
• 2023

In this paper, the selection of a reliable accelerated life test code for a 2-ton forklift was accomplished by choosing the driving resistance coefficient failure-free test time based on a 10,000-hour B₁₀ life. The overall life and average equivalent load of the vehicle were then calculated based on actual driving test conditions using the selected driving resistance coefficient. The gear train's accelerated life test code was selected by adjusting the equivalent load to a torque and rotation speed that did not exceed 125%(about 75HP) of the vehicle rated power. The safety of the test standards was validated by conducting an actual accelerated life test utilizing the proposed test method in this study and comparing the test result with the corresponding theoretical value. It is anticipated that the reliability of the accelerated life test in this paper will be enhanced, by incorporating actual driving performance data collected directly from the forklift and adjusting the conditions used in developing the accelerated life test code.

• 드라이브 ㆍ 컨트롤
• /
• 제20권2호
• /
• pp.24-30
• /
• 2023

This study aimed to analyze the fatigue of forklifts in industrial settings by assessing their stress levels during operation. Strain gauges were affixed to the dynamic components of the forklifts to gather real-time data and enhance the reliability of the analysis. Although monitoring structural loads in harsh testing environments can be challenging, the affixed strain gauges on the dynamic components can provide more precise results and improve the interpretation of data. By creating testing modes that simulate forklift usage environments and performing experiments with selected cargo and driving modes, a comparison of the damage severity of forklift parts under different driving conditions was done. These results can be utilized to forecast the lifespan of forklift parts under extreme driving conditions and assist in the design and optimization of new parts in the future.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.309-313
• /
• 2006

Many researchers have studied on the lightness of automobile. These researches are such as a body shell, sub frame, fuel tank, engine etc. The transmission Part is a magnitude one in the aspect of weight. A drive shaft (propeller shaft) transmits the engine power to rear differential gear assembly. It is used in the compact car that is a single drive shaft. But in the case of long body cars such as SUV (Sports Utility Vehicle), truck and large vehicle, two or three divided drive shaft are used to prevent the vibration damage from a drive shaft that has been taken high torsion and rotation. This multi-divided drive shaft structure is so heavy because it is assembled by yoke, center bearing and solid spline axis. When the rear axle move up and down, the spline shaft adjust the variation of a length between the transmission and rear axle gearbox. In this paper, it is studied in the experimental method that is a bending vibration characteristic of slip in tube shaped propeller shaft. This type propeller shaft is developed to combine the spline axis with drive shaft and can be light in weight of transmission part.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.819-826
• /
• 2000

This study was performed to develop a measurement system of tractor field performance for plow and rotary operations. Measurement system for tractor consisted of torque sensors to measure torque of drive axles and PTO axle, speed sensors to measure rotational speed of drive axles and engine, microcomputer to control data logger, and data logger as I/O interface system. The measurement system was installed on four-wheel-drive tractor. Four-element full-bridge type strain gages were used for torque measurement of drive axles and optical encoders were used to measure speeds of drive axles and engine. Slip rings were mounted on the rotational axles. Signals from sensors were inputted to data logger that was controlled by microcomputer with parallel communication. Sensors were calibrated before the field tests. Regression equations were found on completion of the calibrations. The field experiment was performed at paddy fields and uplands. Rotary and plow were used when the tractor was operated in the field. Travelling speeds of the tractor were 1.9 km/h, 2.7 km/h, 3.7 km/h, 5.5 km/h, 8.2 km/h, and 11.8 km/h. Operating depths of implements were maintained approximately 20cm during the tests. Torque data of drive axles were different at each location during plow and rotary operations. Results showed that torque of rear axles were greater than those of front axles. Total torque were 6860 - 11064 Nm at the upland and 7360 - 14190 Nm at the paddy field for plow operations. It was found that torque at the paddy field were about 20% greater than those at the upland for plow operations. Torque data showed that rotary operations required less power than plow operation at the paddy field and the upland. Torque measurements at each axle for rotary operations were only 8 - 16% of plow operations in the upland and 15 - 20% in the paddy field.

• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.110-115
• /
• 2005

Driving performance is affected by a steering mechanism and characteristics of the ground at off-road skateboarding. In order to drive on off-road, it is necessary off-road wheel and high performance steering mechanism to adapt on various configuration of the ground. In this paper, design factors are studied to affect to steering radius such as inclination angle of a king-bolt, distance of a wheel axle, and rolling angle of a deck plate. A steering system is adhered to inclination face of the deck plate. And, inclination angle is existed between the king-bolt and the flat face of the deck plate. Therefore, the wheel axle of the steering system can be steered by control of the rolling angle of the deck plate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1103-1104
• /
• 2011

This paper presents 1kW BLDC motor drive system and magnetic coupler for water thrust in ROV. In order to get a high performance and reliability, some design flow is proposed in this paper. The proposed system is verified by the experimental tests.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 춘계학술대회 논문집
• /
• pp.183-184
• /
• 2010

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.42-48
• /
• 1997

Drive systems are composed of spiral bevel gear, axle and bearings. In this paper, drive systems and the part of them are analyzed and a correlation of the factor that shows the geometry of spiral bevel gear is evaluated. The Weibull distribution of probability for survival, which caused by the load of bearings and gear teeth, would be calculated, and the life and reliability with equivalent function could be measured more specifically. The reliability methods are applied as a probability of which the gear drive systems are satisfiably operated.

• 드라이브 ㆍ 컨트롤
• /
• 제17권4호
• /
• pp.125-132
• /
• 2020

The objective of this study was to analyze the axle load of a rice transplanter when planting rice seedlings at different working load conditions to select a suitable gear stage and a constant planting depth for rice seedlings. In this study, there are four levels of planting distances (26, 35, 43, and 80 cm) and three planting depths (low, medium, and high) with two gear stages (1.3 and 1.7 m/s). Axle loads and required planting pressures were analyzed statistically. It was observed that axle torques were increased with increasing planting depths for both gear stages, meaning that axle torques were directly proportional to planting depths for both gear stages. It was also observed that required planting pressures had a significant difference between planting distances. Planting pressures also showed significant difference according to gear stage and planting depth. These results indicate that planting pressures were directly proportional to both gear stage and planting depth. Results revealed that the automatic depth control system of a rice transplanter could not guarantee a constant planting depth as supplied pressures were variable. This indicates that a control algorithm is needed to ensure a constant planting depth. In the future, a control algorithm will be developed for an automatic depth control system of a rice transplanter to improve its comprehensive performance and efficiency.