• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1997년도 특별강연 및 춘계학술발표 개요집
• /
• pp.91-98
• /
• 1997

This research is to evaluate of the J-R curve characteristic in 5083 aluminum alloy weldment by utilizing the load ratio analysis. This analysis method can be evaluated the J-R curve only with load-displacement curve without any particular precision instrument equipment in CT specimen. For validity, the results of the load ratio analysis are compared with the those of the J-R curve, which are obtained by the ASTM standard unloading compliance method. The calculated crack length of the load ratio analysis is well appropriate that the measured final crack length. And the J-R curve slope estimated by the load ratio analysis is slightly smaller than that by the ASTM unloading compliance method.

• 한국지반공학회논문집
• /
• 제21권5호
• /
• pp.187-196
• /
• 2005

풍화 및 절리가 발달한 암반에 근입된 말뚝의 허용지지력 결정에는 침하량이 매우 중요한 인자가 되며, 설계단계에서 말뚝두부의 침하량을 예측하기 위해서는 말뚝의 하중전이기구에 대한 이해가 필수적이다. 따라서 본 연구에서는 풍화된 암반에 근입된 현장타설말뚝의 하중전이기구에 대한 연구를 수행하였다. 이를 위해 직경 1m의 총 5본의 현장 타설말뚝을 풍화된 편마암 부지에 시공하구 재하시험 및 하중전이 계측을 수행하여 말뚝의 축방향 지지거동을 분석하였다. 암반상태를 정량적으로 파악하기 위하여 재하시험 부지의 암반에 대한 엄밀한 현장/실내시험을 수행하고, 이를 토대로 암반상태가 말뚝의 하중전이기구에 미치는 영향을 분석하였다. 하중전이 계측을 통해 얻은 주면하중전이 (f-w) 곡선은 풍화상태가 상대적으로 양호한(MW) 연암의 경우, 수 mm의 변위에서 항복에 도달하며, 이후 변위에 따른 지지하중의 증가율이 급격히 둔화되는 경향을 보였다. 반면 풍화암/풍화토에 근입된 말뚝의 f-w 곡선은 뚜렷한 항복점을 보이지 않으며, 상대적으로 큰(>15m) 변위까지 주면하중이 쌍곡선 형태로 증가하였다. 선단하중전이(q-w) 곡선은 암반상태에 관계없이 선단변위 (q-w)까지는 선형적인 거동을 보였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.368-371
• /
• 2008

An extensometer system to measure strain and displacement of cylindrical fatigue specimen in a autoclave of high temperature and high pressure environment has been developed by KEPRI. The extensometer reads the displacement caused by fatigue loads at the target length of the specimen installed inside the autoclave. The performance of the extensometer were tested at 15MPa, $315^{\circ}C$ of a operating pressurized water reactor. Two LVDT's of magnet type were connected to the extensometer and used for converting the fatigue displacement to electronic signal. The device is being used for developing environmental fatigue curve of CF8M cast austenitic stainless steel (CASS) in the test condition of low cycle and low strain. This paper introduces the background and results of the development.

• 대한토목학회논문집
• /
• 제14권3호
• /
• pp.553-563
• /
• 1994

본 연구에서는 탄소성 지반에서 지반스프링의 Coupling을 고려하여 토류벽의 거동을 해석하였다. 수치해석을 위해 벽체 양측의 지반을 탄소성 스프링으로 단순화하였고, 지반반력계수의 산정을 위해서 Terzaghi가 제안한 주동 및 수동상태에 필요한 수평변위를 p-y 특성곡선에 적용하였다. 본 연구에서 개발된 전산프로그램의 신뢰성은 기존 컴퓨터 프로그램 및 현장 실측치와의 비교를 통해 검증하였다. 검증결과 지반스프링의 Coupling을 고려한 경우가 현장 실측치의 변위 및 토압에 접근함을 알 수 있었고, 모래질 흙에서 주동상태에 필요한 수평변위의 변화가 벽체의 변위에 이주 작은 영향만을 준다는 것을 알 수 있었다.

• Steel and Composite Structures
• /
• 제18권6호
• /
• pp.1557-1568
• /
• 2015

The nonlinear static analysis of structure, which is under the effect of lateral loads and provides the capacity curve of the structure, is defined as a push-over analysis. Ordinarily, by using base shear and the lateral displacement of target point, the capacity curve is obtained. The speed and ease of results interpretation in this method is more than that of the NRHA responses. In this study, the nonlinear static analysis is applied on the semi-rigid steel gabled frames. It should be noted that the members of this structure are analyzed as a prismatic beam-column element in two states of semi-rigid connections and supports. The gabled frame is modeled in the OpenSees software and analyzed based on the displacement control at the target point. The lateral displacement results, calculated in the top level of columns, are reported. Furthermore, responses of the structure are obtained for various support conditions and the rigidity of nodal connections. Ultimately, the effect of semi-rigid connections and supports on the capacity and the performance point of the structure are presented in separated graphs.

• Geomechanics and Engineering
• /
• 제16권1호
• /
• pp.59-69
• /
• 2018

This study focused on the mechanical and hydraulic characteristics of underwater tunnels based on Mohr-Coulomb (M-C), Hoek-Brown (H-B) and generalized H-B failure criteria. An improved approach for calculating stress, displacement and plastic radius of the circular tunnel considering hydraulic-mechanical coupling was developed. The innovation of this study was that the radius-incremental-approach was reconstructed (i.e., the whole plastic zone is divided into a finite number of concentric annuli by radius), stress and displacement of each annulus were determined in terms of numerical method and Terzaghi's effective stress principle. The validation of the proposed approach was conducted by comparing with the results in Brown and Bray (1982) and Park and Kim (2006). In addition, the Rp-pin curve (plastic radius-internal supporting pressure curve) was obtained using the numerical iterative method, and the plastic radius of the deep-buried tunnel could be obtained by interpolation method in terms of the known value of internal supporting pressure pin. Combining with the theories in Carranza and Fairhurst (2000), the improved technique for assessing the reliability of the tunnel support was proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.101-106
• /
• 2003

In order to investigate the mechanical behavior of newly developed materials, the evaluation of mechanical properties using small-size specimen is essential. For those purposes, an instrumented impact testing apparatus, which provides the load-displacement curve under impact loading without oscillations, was devised. To develop the test procedure with the setup, the impact behaviors of various kinds of structural materials such as S45C, SCM4, Ti alloys (Ti-6V-4Al) and Zr-based bulk amorphous metal, were investigated through the instrumented Charpy V-notch impact tests. The calibrations of the dynamic load and displacement that was calculated based on the Newton' second law were carried out through the quasi-static load test and the comparison of a directly measured value using a laser displacement meter. Satisfactory results could be obtained. The crack initiation and propagation processes during impact fracture could be well divided on the curve, depending on the intrinsic characteristic of specimen tested; ductile or brittle. The absorbed impact energy in Zr-basd BAM was largely used for crack initiation not for crack propagation process. The fracture surfaces under impact loading showed different feature when compared with the static cases.

• 한국소음진동공학회논문집
• /
• 제20권5호
• /
• pp.477-485
• /
• 2010

In this study, we suggested several approaches to evaluate the collision acceleration of a carbody under the article 16 of the Korean rolling stock safety regulations. There are various methods to evaluate the rigid body accelerations such as the displacement comparison method by double integration of filtered acceleration data, the velocity comparison method by direct integration of filtered acceleration data, and the analysis method of a velocity-time curve. We compared these methods one another using the 1D dynamic simulation model of Korean high-speed EMU composed of nonlinear springs or bars, dampers, and masses. From the simulation results, the velocity-time curve analysis method and the displacement comparison method are recommended to filter high frequency oscillations and evaluate the maximum and average accelerations of a carbody after a train collision.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.481-486
• /
• 1998

In this paper, elastic and inelastic behavior of exterior joint of moment-resisting R.C frame with non-seismic detail subjected to reversed cyclic lateral load such as earthquake excitations was investigated. 1/2-scals subassemblage exterior beam-column joint including slab was manufactured based on similitude law. Then, pseudo static test under the displacement control was performed. The results of 1)crack pattern and failure mode, 2)degradation stiffness and strength, energy dissipation capacity from load-displacement hysteresis curve, 3)strain of steel were analysed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1353-1357
• /
• 2005

A CAM program for forming design Automated of CAM for Spring using car was developed in this study. This program was written in AUTO-LISP on the AUTO-CAD system with a personal. An approach to the system is based on the kinemateic of the object function. We make a determination of an cam programming. A cam spline is continuous in displacement, velocity and acceleration. The best cam curve is obtained by changing the kinemateic of the object function. The result has improved all characteristics such as velocity, acceleration and displacement compared with that of the modified cycloid curve.