• Membrane Journal
• /
• v.22 no.4
• /
• pp.235-242
• /
• 2012

Ammonium perchlorate (AP) is primarily derived from the process of liquid incineration treatment when dismantling a solid rocket propellant. A series of batch dead-end nanofiltration (NF) and reverse osmosis (RO) membrane experiments were conducted to explore the retention mechanisms of AP under various hydrodynamic and solution conditions. Low levels of silicate type of siloxane had been detected through the GC/MS and FTIR analysis of liquid solutions extracted from solid ammonium perchlorate composite propellant (APCP). It is indicated that NF/RO membranes fouling in the presence of APCP was mainly attributed to the AP interactions because the concentration of silicate type of siloxane was negligible compared to that of AP. The osmotic pressure of AP was presumably resulted in the flux declines ranging from 13 to 17% in the case of the application of low-pressure (551 and 896 kPa for NF and RO) compared to those in application of high-pressure. The retention of AP by NF/RO membranes significantly varied from approximately 10 to 70% for NF and 26 to 87% for RO, depending on the operating and solution water chemistry conditions. The results suggested that retention efficiency of AP was fairly increased by reducing concentration polarization (i.e. application of low-pressure and stirring speed of 600 rpm) and increasing the pH of a solution. The result of this study was also consistent with the previous modeling of 'solute mass transfer of NF/RO membranes' and demonstrated that hydrodynamic and solution water chemistry conditions are to be a key factor in the retention of AP by NF/RO membranes.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.4
• /
• pp.349-360
• /
• 2017

In concrete construction work, formwork is an important process that accounts for 10% of the total construction cost. Recent buildings are becoming bigger and higher. In order to maximize the efficiency and safety of this formwork, the system of formworking has been systematized. However, the human accidents and the noise complaints arise from dismantling processes frequently occur. In order to solve these problems, most of them are dependent on foreign technology, but they do not take into consideration the conditions of domestic construction site. In this study, we developed a table type multi-drop system form for a slab and beam which can improve the process, safety and reduction of disassembly noise, and evaluated the physical properties of the main members which are used in the system. The results of this study show that there is sufficient strength to be used as a slab and a laying material for both a yoke beam and a supporting post. The noise level is improved compared to existing method.

• Journal of Conservation Science
• /
• v.19
• /
• pp.5-18
• /
• 2006

The Mireuksaji stone pagoda of the Iksan was built in Muwang King of Baekjae Kingdom and has maintained its present status through several rebuilding process. Recently, the structural unbalance of the pagoda has worsened, so for scientific maintenance recovery of its original pagoda form, the pagoda is under dismantling process. The original form of this pagoda is being presumed to be a plane square pagoda of nine stories, though only a portion of six stories remains until today. The destroyed part from collapse was liked in insecure pagoda form by Japanese in year of 1915. On the surface of the stone which has gone through the present time, efflorescence appeared as precipitation substance over crusted and due to this phenomenon, the structure and color of thee original stone haven't been preserved. Therefore, quantitative analysis on its kind, emitted status and contamination type of secondary inorganic contamination substance of the over crusted surface were analyzed. Also through reaction experiments, contamination type was defined and tests have been applied to find the requirements that will wash out the contaminants. The result of this study will provide the base of quantitative analysis on the kind of inorganic contamination of the surface of stone assets, and it shall also contribute to the application of scientific maintenance recovery of surface cleaner for efflorescence.

• Journal of Environmental Health Sciences
• /
• v.17 no.1
• /
• pp.95-103
• /
• 1991

For the purpose of estimating the working environment and the relationship between the airborne lead concentration and the ZPP level in the whole blood of the workers, the airborne lead concentrations and the ZPP level were measured at the 26 plants which deal with lead, from October 5 to November 5 in 1988. Analysis of the airborne lead concentration was performed by NIOSH Method 7082, and the ZPP level was measured by a hematofluorometer. The following results are concluded. 1. The average airborne lead concentration of the lead battery manufactures is 0.025mg/m$^{3}$ and that of the secondary lead smelters is 0.023mg/m$^{3}$. There were no significant differences between industry (p>0.1) 2. At the lead battery manufacture, the process of lead powder production showed the highest concentration of 0.034mg/m$^{3}$ but there were no significant differences among the processes (p>0.1). At the secondary lead smelter, the process of dismantling waste batteries showed the highest concentration 0.141mg/m$^{3}$, and there were very significant differences among the processes (p<0.005). 3. The ZPP level in the whole blood showed significant differences between industry (p<0.10). The average ZPP level of the lead battery manufactures is 133.0 + 106.3 $\mu$g/100ml and that of the secondary lead smelters is 149.6 + 110.9 $\mu$g/100ml. 4. The correlation coefficients between the airborne lead concantration and ZPP level were 0. 426 (p<0.001) for the lead battery manufactures and 0.484 (p<0.001) for the secondary lead smelters. The correlation coefficients between the work duration (in months) and the ZPP level were 0.238 (p<0.001) for the lead battery mannfactures and 0.075 (p>0.10) for the secondary lead smelters. 5. The linear regression equation, with the airborne lead concentration as an independent variable and the ZPP level as a dependent variable, is Y=96.84+1300.34X (r=0.448, p<0.001) for the 26 plants which deal with lead. The linear regression equation, with the work duration(in months) as an independent variable and the ZPP level as a dependent variable, is Y=127.28 +0.49X (r=0.162, p<0.05). 6. The correlation coefficients between the amount of inhaled lead and ZPP level were 0.349 (p < 0.001) for the lead battery manufactures and 0.318(p<0.001) for the secondary lead smeltes. The linear regression equation for the 26 plants surveyed, with the amount of inhaled lead as an independent variable and ZPP level as a dependent variable, is Y=123.63+18.82X (r=0. 335, p<0.001).

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.4
• /
• pp.403-414
• /
• 2022

Many studies have been conducted on asset management of public facilities, as the importance of such management has been increasing. This basic study aims to present strategies for the practical use of public asset management, and seeks to propose efficient management and utilization measures from a cost perspective by comparing and analyzing the importance and impact relationship between cost items for public asset management. In this study, 19 sub-items and the top 4 items were chosen by deriving cost factors based on the previous literature. A survey was conducted, and the results of the survey were analyzed by using the Analytic Hierarchy Process(AHP) and Interpretive Structural Modeling (ISM) methods. The AHP was used to derive the priority between items, and ISM was used to identify major groups and mutual influences. As a result, those items showing both high priority and high importance, such as user cost, dismantling/disposal cost, replacement cost, maintenance/repair cost, etc. are determined as priority items to be considered for public asset management of public facilities. Also, it is necessary to minimize the impact on other items in public asset management by those items which are impacted less by other items but have significant impact on the items such as initial construction costs, conceptual design costs, construction costs, and supervision costs. It is expected that the results and analysis methods presented in this study can be used to provide strategies for asset management of public facilities.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.5
• /
• pp.469-475
• /
• 2022

As the recent structure construction is constructed as a large-scale and deep underground excavation in close proximity to the building, the installation of retaining wall and supporters (Struts) has become complicated, and the number of supporters to avoid interference of the structural slab has increased. This construction process becomes a factor that causes an increase in construction joints of a structure, leakage and an increase in wall cracks. In addition, this reduced the durability and workability of the structure and led to an increase in the construction period. This study planned to dismantle the two struts simultaneously as a plan to reduce the construction joints, and corrected the earth pressure by assuming the reaction force value by the initial earth pressure and the measured data as the response ratio. After recalculating the corrected earth pressure through the iterative trial method, it was verified by numerical analysis that simultaneous disassembly of the two struts was possible. As a result of numerical analysis applying the final corrected earth pressure, the measured value for the design reaction force was found to be up to 197%. It was analyzed that this was due to the effect of grouting on the ground and some underestimation of the ground characteristics during design. Based on the result of calculating the corrected earth pressure in consideration of the response ratio performed in this study, it was proved analytically that the improvement of the brace dismantling process is possible. In addition, it was considered that the overall construction period could be shortened by reducing cracks due to leakage and improving workability by reducing construction joints. However, to apply the proposed method of this study, it is judged that sufficient estimations are necessary as there are differences in ground conditions, temporary facilities, and reinforcement methods for each site.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.72-80
• /
• 2004

Electrolytic dissolution study was carried out to evaluate the applicability of electrochemical decontamination process using a neutral salt electrolyte as a decontamination technology for the recycle or self disposal with authorization of large amount of metallic wastes contaminated with uranium compounds generated by dismantling a retired uranium conversion plant using SUS-304 and Inconel-600 specimen as the main materials of internal system components of the plant. The effects of type of neutral salt as an electrolyte, current density, and concentration of electrolyte on the dissolution of the materials were evaluated. On the basis of the results obtained through the basic inactive experiments, electrochemical decontamination tests using the specimens contaminated with uranium compounds such as $UO_2$, AUC (ammonium uranyl carbonate) and ADU (ammonium diuranate) taken from an uranium conversion plant were peformed in $Na_2SO_4$ and $NaNO_3$ solution. It was verified that the electrochemical decontamination of the dismantled metallic wastes was quite successful in $Na_2SO_4$ and $NaNO_3$ neutral salt electrolyte by reducing $\beta$ radioactivities below the level of self disposal with authorization within 10 minutes regardless of the type of contaminants and the degree of contamination.

• Resources Recycling
• /
• v.14 no.3
• /
• pp.16-36
• /
• 2005

The quantity of passenger cars in industrial countries has been significantly increased in recent years. According to prognoses, this tendency is likely to continue in the forthcoming future. As a direct consequence, an increase of End-of Life-Vehicles (ELV) will confront us with the problem of "ELV-Recycling". In order to cope with this situation, the European regulation for the treatment of End-of-Life-Vehicles (09/2000) has been transferred to national law in Germany (ELV-Regulation from 1 July 2002). The long term aim is to reduce residues from the ELV-treatment to less than 5 wt% from 30 wt% within the next 10 years (2015). For that reason, there is a need for innovative and more efficient recycling techniques tailored to future materials in automobiles. The design process at automotive industry is continuously changing due to the strong demand on optional equipment and new technical solutions for fuel saving. Light materials, such as aluminum and plastics, consequently become more important and cause a decrease of ferrous metals. Since plastic materials are often used as compounds, a separation into initial material types by means of mechanical recycling methods is not possible. For that reason, efficient recycling can only be realized by introducing recycling-friendly car designs. In the end an integrated approach of auto makers and recycling industry is of decisive significance for the fulfillment of future regulations.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.427-434
• /
• 2017

The generation of construction waste can be divided into a decommissioning phase and a new construction phase, and most of the waste is generated at the decommissioning stage. However, recently, domestic new construction construction has expanded to 150 trillion yards per year, so construction work is increasing rapidly. Especially, as the size of the construction work with much waste of construction waste exceeds 100 trillion, the management of the amount of construction waste in the new construction site is required. Unlike the dismantling work site, the new construction site can separate waste generated by each property, and relatively low foreign matter content is generated. The purpose of this study was to investigate the amount of construction waste generated by new construction sites and to calculate the unit amount of construction waste based on this. In addition, since the existing unit cost is centered on concrete and mixed waste, we set the basic unit by setting synthetic resin, waste wood, and waste board as additional items. The basic unit survey was carried out to investigate the wastes according to the characteristics of each construction period. As a result of the survey, the new construction site showed that most wastes were discharged in the first 30% and after 70% of the process, and the ratio of mixed construction waste was as high as 45%. As a result of this study, it was found that about twice as much waste was produced as compared with the conventional standard product.

• Journal of the Korean Society of Costume
• /
• v.51 no.5
• /
• pp.113-134
• /
• 2001

This study was carried out with an objective to prepare the framework of conformity for the 21st century modern fashion, which is interactive with mankind, based on a position that the 21st century contemporary fashion with its amalgamating trend of diversified artistic forms may not be elucidated on a standpoint centering on one certain modality. The hybrid fashion trend of historical modality which provides freedom and satisfaction in creation of an individuals expressive power in expressing true desire of mans inside through man-centered thought of the times has made multifarious motives of the past and present fragmentary. It thus extracts inner divisions and the concept of consolidation through three-dimensional form. Modern fashion is newly interpreted by the material and details of high technologies. and is harmonized by mix and match with various expressions. By having it, it is being expressed together with many types of dresses and ornaments. Modern fashion is being expressed together with many types of dresses and ornaments by new interpretations with the material and details of high technologies and by being harmonized with mix and match with various expressions. The hybrid fashion design trend of regional elements formed by stimuli and contacts of diverse local culture by globalization of network that was achieved by scientific technologies of the contemporary information society has disintegrated varied boundaries in the conventional culture by the latest communication technology-new media on the basis of newly created culture. The fact that regional elements could be expressed as if they were interrelated without each being deprived of originality may be explained with an interpretation on pluralism. The hybrid fashion design trend of cultural aspect, which manifests in the background of scientific technological culture as it transcends the societal-cultural boundaries based on the de-centralization theory of Frederic Jameson, has supplemented the imperfect meanings through conversional correlation with other forms and internal program changes. The middle stratal and polyhedral characteristics are seen as each cultural element is dismantled and reassembled by application of 'multiple-time point expression'. Design forming method is not to bring destruction from outside, but to embrace instability and chaos through radical dismantling of the inside. and to pursue diversity and openness. Thus. it is implemented by an approach that takes the role of design process. In communication of discontinuity, continuity was dismantled through forms of mixing, overlap, perversion, insertion and coincidence.