• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.262-263
• /
• 2006

The free sintering of metallic powders blended with non sintering inclusions is investigated by the Discrete Element Method (DEM). Each particle, whatever its nature (metallic or inclusion) is modeled as a sphere that interacts with its neighbors. We investigate the retarding effect of the inclusions on the sintering kinetics. Also, we present a simple coarsening model for the metallic particles, which allows large particles to grow at the expense of the smallest.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.187-188
• /
• 2006

In contrast with the Finite Element Method, the Discrete Element Method (DEM) takes explicitly into account the particulate nature of powders. DEM exhibits some drawbacks and many advantages. Simulations can be computationally expensive and they are only able to represent a volume element. However, these simulations have the great advantage of providing a wealth of information at the microstructural level. Here we demonstrate that the method is well suited for modelling, in coordination with FEM, the compaction of ceramic $UO_2$ particles that have been aggregated. Aggregates of individual ceramic crystallites that are strongly bonded together are represented by porous spheres.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.86-91
• /
• 2020

An important factor of rough road modeling is analyzing the shear behavior properties of the rough road. These properties influence the drawbar pull of the tool when interacting with the soil used in agriculture. Furthermore, shear behavior properties are important because sinkage and shear stress are generated when wheels drive on rough roads. In this study, we performed a direct shear test to investigate the shear behavior properties of soils and compare with the direct shear simulation; shear force derived by the coupled analysis of discrete element method; and multi-body dynamics. Soil contact parameters were measured in a wheel and soil contact simulation followed by comparison of the simulated and experimentally measured shear force.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.146-153
• /
• 2004

This paper presents a discrete analysis approach to investigate the performance of dual mass flywheel (DMF). In the discrete analysis, arcspring installed between the flywheels is modeled as N- discrete elements. Each element consists of mass, spring and nonlinear friction element. LuGre friction model is used to describe nonlinear friction characteristic. Based on the dynamic models of the DMF, clutch, engine, manual transmission and vehicle, a DMF performance simulator is developed using MATLAB Simulink. Simulation results of the engine speed, driveshaft torque and vehicle velocity are compared with test results. It is found that the discrete DMF model describes the vehicle behavior closely, especially during the clutch actuation period.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.59-68
• /
• 2007

The comparative study using the lab-scale experiment and the discrete element analysis is attempted to analyze the cross-anisotropic elasticity of granular soils. The lab-scale experiment consists of the small stress-controlled triaxial cyclic tests and the bender element tests. In the discrete element analysis the simulations of lab-scale cyclic tests are conducted in the various directions. Good agreement between the experimental data and the simulation on the elastic properties in the axial and shear directions confirms the usefulness of the discrete element method. The comparative analysis of the difference in the experimental data and the simulation of radial cyclic tests shows that the discrete element method can successfully be used to check the reasonable magnitude of each measurement in the experiments.

• Journal of the Korean Society for Railway
• /
• v.6 no.3
• /
• pp.174-178
• /
• 2003

This paper presents the development of 2-dimensional discrete element algorithm to generate circle and line elements for the simulation of the ballast and sleeper in railway. An example of randomly distributed circle elements show a good applicability of this algorithm for the modeling of the behaviors of ballast. The output about unbalaned force, particle velocity, and total energy conservation from the code is evaluated to check if the calculation is conducted properly.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.93-98
• /
• 2020

Washboarding is a phenomenon in which a wavy shape occurs periodically and naturally on an unpaved road made of soil or gravel. This phenomenon causes high-frequency vibration of the traffic traveling on the road because of the height difference of the wave pattern, which may lead to vehicle failure. Consequently, associated research is needed concerning vehicle safety. Therefore, in this study, a numerical simulation was conducted using the discrete element method, which is often used for powder simulation. In contrast to previous studies, the results of this study demonstrate that washboarding can occur even in an environment of 1.5 m/s or less. However, the amount of washboarding is minimal. The study revealed that washboarding develops over time, such that sufficient development time is required before measurements are taken.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.136-146
• /
• 2021

This paper aims to numerically estimate the dynamic ice load on a conical structure. The Discrete Element Method (DEM) is employed to model the level ice as the assembly of numerous spherical particles. To mimic the realistic fracture mechanism of ice, the parallel bonding method is introduced. Cases with four different ice drifting velocities are considered in time domain. For validation, the statistics of time-varying ice forces and their frequencies obtained by numerical simulations are extensively compared against the physical model-test results. Ice properties are directly adopted from the targeted experimental test set up. The additional parameters for DEM simulations are systematically determined by a numerical three-point bending test. The findings reveal that the numerical simulation estimates the dynamic ice force in a reasonably acceptable range and its results agree well with experimental data.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.4
• /
• pp.1-7
• /
• 2016

The pick cutter, which directly contacts and crushes the rock, is the expendable part of a roadheader. The arrangement and angle of attachment of the pick cutter are important factors that determine excavator performance. It is necessary to numerically calculate the contact between the pick cutter and rock. The rock is defined as a set of particles using the discrete element method. The parallel bond model is used to define the bonds between particles. The properties of granite that are measured by the uniaxial compressive test are applied to the numerical rock model. The pick cutter is defined by the polygon elements. The linear cutting simulation is considered to simulate the contact between the pick cutter and rock. The results of the simulation show the rock breaking due to contact with the pick cutter.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.59-69
• /
• 2019

This paper focuses on the numerical simulation of ice abrasion induced by unbreakable ice floe. Under the assumption that unbreakable floes behave as rigid body, the Discrete Element Method (DEM) was applied to simulate the interaction between a fixed structure and ice floes. DEM is a numerical technique which is eligible for computing the motion and effect of a large number of particles. In DEM simulation, individual ice floe was treated as single rigid element which interacts with each other following the given interaction rules. Interactions between the ice floes and structure were defined by soft contact and viscous Coulomb friction laws. To derive the details of the interactions in terms of interaction parameters, the Finite Element Method (FEM) was employed. An abrasion process between a structure and an ice floe was simulated by FEM, and the parameters in DEM such as contact stiffness, contact damping coefficient, etc. were calibrated based on the FEM result. Resultantly, contact length and contact path length, which are the most important factors in ice abrasion prediction, were calculated from both DEM and FEM and compared with each other. The results showed good correspondence between the two results, providing superior numerical efficiency of DEM.