• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.262-263
• /
• 2006

The free sintering of metallic powders blended with non sintering inclusions is investigated by the Discrete Element Method (DEM). Each particle, whatever its nature (metallic or inclusion) is modeled as a sphere that interacts with its neighbors. We investigate the retarding effect of the inclusions on the sintering kinetics. Also, we present a simple coarsening model for the metallic particles, which allows large particles to grow at the expense of the smallest.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.187-188
• /
• 2006

In contrast with the Finite Element Method, the Discrete Element Method (DEM) takes explicitly into account the particulate nature of powders. DEM exhibits some drawbacks and many advantages. Simulations can be computationally expensive and they are only able to represent a volume element. However, these simulations have the great advantage of providing a wealth of information at the microstructural level. Here we demonstrate that the method is well suited for modelling, in coordination with FEM, the compaction of ceramic $UO_2$ particles that have been aggregated. Aggregates of individual ceramic crystallites that are strongly bonded together are represented by porous spheres.

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.86-91
• /
• 2020

An important factor of rough road modeling is analyzing the shear behavior properties of the rough road. These properties influence the drawbar pull of the tool when interacting with the soil used in agriculture. Furthermore, shear behavior properties are important because sinkage and shear stress are generated when wheels drive on rough roads. In this study, we performed a direct shear test to investigate the shear behavior properties of soils and compare with the direct shear simulation; shear force derived by the coupled analysis of discrete element method; and multi-body dynamics. Soil contact parameters were measured in a wheel and soil contact simulation followed by comparison of the simulated and experimentally measured shear force.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.146-153
• /
• 2004

This paper presents a discrete analysis approach to investigate the performance of dual mass flywheel (DMF). In the discrete analysis, arcspring installed between the flywheels is modeled as N- discrete elements. Each element consists of mass, spring and nonlinear friction element. LuGre friction model is used to describe nonlinear friction characteristic. Based on the dynamic models of the DMF, clutch, engine, manual transmission and vehicle, a DMF performance simulator is developed using MATLAB Simulink. Simulation results of the engine speed, driveshaft torque and vehicle velocity are compared with test results. It is found that the discrete DMF model describes the vehicle behavior closely, especially during the clutch actuation period.

• 한국지반공학회논문집
• /
• 제23권8호
• /
• pp.59-68
• /
• 2007

사질토의 직교 이방 탄성계수를 실험적 방법과 개별 요소법을 이용하여 측정하고 결과를 정량적으로 비교-분석하였다. 실내 시험에서는 미소 응력 제어 반복재하시험과 벤더 엘리먼트의 측정 결과를 조합하여 탄성 특성을 구하였으며, 개별 요소법에서는 실내 시험 방법과 상응하는 반복재하시험을 모사하였다. 축 방향 및 전단방향에 관련된 탄성 특성의 비교 결과는 제한된 조건에서도 개별 요소법이 복잡한 실내 시험 과정을 모사할 수 있음을 보여주었다. 방사 방향 재하시험 결과에서 나타난 두 방법 간 차이의 비교 분석 결과는 개별 요소법이 실내 시험으로 구한 개별 측정치의 정량적 타당성을 확인하는데 충분히 활용될 수 있음을 보여준다.

• 한국철도학회논문집
• /
• 제6권3호
• /
• pp.174-178
• /
• 2003

This paper presents the development of 2-dimensional discrete element algorithm to generate circle and line elements for the simulation of the ballast and sleeper in railway. An example of randomly distributed circle elements show a good applicability of this algorithm for the modeling of the behaviors of ballast. The output about unbalaned force, particle velocity, and total energy conservation from the code is evaluated to check if the calculation is conducted properly.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.93-98
• /
• 2020

Washboarding is a phenomenon in which a wavy shape occurs periodically and naturally on an unpaved road made of soil or gravel. This phenomenon causes high-frequency vibration of the traffic traveling on the road because of the height difference of the wave pattern, which may lead to vehicle failure. Consequently, associated research is needed concerning vehicle safety. Therefore, in this study, a numerical simulation was conducted using the discrete element method, which is often used for powder simulation. In contrast to previous studies, the results of this study demonstrate that washboarding can occur even in an environment of 1.5 m/s or less. However, the amount of washboarding is minimal. The study revealed that washboarding develops over time, such that sufficient development time is required before measurements are taken.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.136-146
• /
• 2021

This paper aims to numerically estimate the dynamic ice load on a conical structure. The Discrete Element Method (DEM) is employed to model the level ice as the assembly of numerous spherical particles. To mimic the realistic fracture mechanism of ice, the parallel bonding method is introduced. Cases with four different ice drifting velocities are considered in time domain. For validation, the statistics of time-varying ice forces and their frequencies obtained by numerical simulations are extensively compared against the physical model-test results. Ice properties are directly adopted from the targeted experimental test set up. The additional parameters for DEM simulations are systematically determined by a numerical three-point bending test. The findings reveal that the numerical simulation estimates the dynamic ice force in a reasonably acceptable range and its results agree well with experimental data.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.1-7
• /
• 2016

The pick cutter, which directly contacts and crushes the rock, is the expendable part of a roadheader. The arrangement and angle of attachment of the pick cutter are important factors that determine excavator performance. It is necessary to numerically calculate the contact between the pick cutter and rock. The rock is defined as a set of particles using the discrete element method. The parallel bond model is used to define the bonds between particles. The properties of granite that are measured by the uniaxial compressive test are applied to the numerical rock model. The pick cutter is defined by the polygon elements. The linear cutting simulation is considered to simulate the contact between the pick cutter and rock. The results of the simulation show the rock breaking due to contact with the pick cutter.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.59-69
• /
• 2019

This paper focuses on the numerical simulation of ice abrasion induced by unbreakable ice floe. Under the assumption that unbreakable floes behave as rigid body, the Discrete Element Method (DEM) was applied to simulate the interaction between a fixed structure and ice floes. DEM is a numerical technique which is eligible for computing the motion and effect of a large number of particles. In DEM simulation, individual ice floe was treated as single rigid element which interacts with each other following the given interaction rules. Interactions between the ice floes and structure were defined by soft contact and viscous Coulomb friction laws. To derive the details of the interactions in terms of interaction parameters, the Finite Element Method (FEM) was employed. An abrasion process between a structure and an ice floe was simulated by FEM, and the parameters in DEM such as contact stiffness, contact damping coefficient, etc. were calibrated based on the FEM result. Resultantly, contact length and contact path length, which are the most important factors in ice abrasion prediction, were calculated from both DEM and FEM and compared with each other. The results showed good correspondence between the two results, providing superior numerical efficiency of DEM.