• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.47-54
• /
• 2006

This work proposes a dual-channel 6b 1GS/s ADC for ultra wide-band communication system applications. The proposed ADC based on a 6b interpolated flash architecture employs wide-band open-loop track-and-hold amplifiers, comparators with a wide-range differential difference pre-amplifier, latches with reduced kickback noise, on-chip CMOS references, and digital bubble-code correction circuits to optimize power, chip area, and accuracy at 1GS/s. The ADC implemented in a 0.18um 1P6M CMOS technology shows a signal-to-noise-and-distortion ratio of 30dB and a spurious-free dynamic range of 39dB at 1GS/s. The measured differential and integral non-linearities of the prototype ADC are within 1.0LSB and 1.3LSB, respectively. The dual-channel ADC has an active area of $4.0mm^2$ and consumes 594mW at 1GS/s and 1.8V.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.110-120
• /
• 2016

A power-efficient neuromodulator is needed for implantable systems. In spite of their stimulation signal's simplicity of wave shape and waiting time of MCU(micro controller unit) much longer than execution time, there is no consideration for low-power design. In this paper, we propose a novel of low-power algorithm based on the characteristics of stimulation signals. Then, we designed and implement a neuromodulation software that we call NMS(neuro modulation simulation). In order to implement low-power algorithm, first, we analyze running time of every function in existing NMS. Then, we calculate execution time and waiting time for these functions. Subsequently, we estimate the transition time between active mode (AM) and low-power mode (LPM). By using these results, we redesign the architecture of NMS in the proposed low-power algorithm: a stimulation signal divided into a number of segments by using characteristics of the signal from which AM or LPM segments are defined for determining the MCU power reduces to turn off or not. Our experimental results indicate that NMS with low-power algorithm reducing current consumption of MCU by 76.31 percent compared to NMS without low-power algorithm.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.6
• /
• pp.691-702
• /
• 2019

Flood inundation map has various important roles in terms of municipal planning, timely dam operation, economic levee design, and building flood forecasting systems. Considering that the riparian areas adjacent to national rivers with high potential flood vulnerability conventionally imposed special cares to justify applications of recently available two- or three-dimensional flood inundation numerical models on top of digital elevation models of dense spatial resolution such as LiDAR irrespective of their high costs. On the contrary, local streams usually could not have benefits from recent technological advances, instead they inevitably have relied upon time-consuming manual drawings or have accepted DEMs with poor resolutions or inaccurate 1D numerical models for producing inundation maps due mainly to limited budgets and suitable techniques. In order to efficiently and cost-effectively provide a series of flood inundation maps dedicatedly for the local streams, this study proposed an OpenGIS-based flood mapping tool named Open Flood Mapper (OFM). The spatial accuracy of flood inundation map derived from the OFM was validated throughout comparison with an inundation trace map acquired after typhoon Nari in Hancheon basin located in Jeju Island. Also, a series of inundation maps from the OFM were comprehensively investigated to track the burst of flood in the extreme flood events.

• Korean Journal of Construction Engineering and Management
• /
• v.21 no.2
• /
• pp.3-14
• /
• 2020

This study reviews and comparatively analyzes existing classification systems for 3D concrete printers to propose a classification system for 3D concrete printers. Several classifications for existing 3D printers have been proposed and used in the market. Nevertheless, quite a few of the printer types such as fused deposition modeling (FDM) and selective laser melting (SLM) are not suitable for characterizing 3D concrete printers. To derive the properties that distinguish one 3D concrete printer type from the others, this study reviews existing 3D concrete printers and comparatively analyzes the properties of 3D concrete printers identified in previous studies. The results show that existing classifications do not reflect the states-of-the-art of 3D concrete printers, the classification terms are ambiguous, and the entire printing processes are not considered. A new classification system was proposed based on the essential properties of the 3D concrete printers identified through the analysis of related work. The result of this study can be used as a basis for classifying commercial 3D concrete printers as well as studies related to 3D concrete printers.

• The Journal of Korea Assosiation for Disability and Oral Health
• /
• v.13 no.2
• /
• pp.99-103
• /
• 2017

The primary responsibility for the oral hygiene of the disabled is usually the parents. Dental care of the disabled is early detection and recovery of lesions and continuous management. For this to be successful it is necessary to use diagnostic tool that can detect the early stages of dental caries which is difficult to detect with the naked eye. It is also important to educate and motivate the caregivers on oral hygiene management. Quantitative Light-induced Fluorescence-Digital (Billuminator, Inspektor Researh Systems BV, Amsterdam, The Netherlands), which provides overall caries inspection and visual information, can be useful for caregiver education. A 3-year-old girl who was hospitalized with Pallister-Killian syndrome, Hypothyroidism visited our clinic with chief complaint of rugged upper incisors. This girl had multiple dental caries and oral hygiene was very poor. Periodic QLF-D images were taken to provide caregiver education and oral hygiene management was improved. A 13-year-old girl with cerebral palsy visited our clinic for regular check up. Using QLF-D, we explained to the parents that there is a need for treatment of dental caries, and education of oral hygiene management was conducted. Improvement of oral hygiene in the disabled can be achieved through caregiver education. QLF-D is a diagnostic device that can detects early caries by irradiating light in the visible ray area to the teeth. It can also detects microleakage of restoration, plaque and calculus without disclosing agent. Clinicians can use the QLF-D to perform a general oral examination for the disabled. Also, QLF-D can be used to store visual information and educate caregivers. The accumulation of information using QLF-D makes it possible to provide feedback on oral care of parents, which is more advantageous for caregivers education.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.27-32
• /
• 2014

A doppler shift is generated by moving a transmitter or receiver operated in communication systems. The doppler frequency shift between a transmitter and a receiver or the frequency offset present in transceivers must be removed to get the wanted system performance. FTS is used for preventing an accident from operating abnormally and for guaranteeing public protection. A launching vehicle's initial velocity is very fast in order to escape the earth and the amount of doppler shift is large. Recently many studies to adopt the next generation FTS are ongoing. To introduce new FTS, the effects of doppler shift on the performance of the new FTS must be studied. In this paper the doppler effect caused by launching vehicle's velocity affecting the performance of FTS receiver is investigated into two cases, one is for EFTS as a digital FTS and the other is for FTS using a tone signal. Noncoherent DPSK and noncoherent CPFSK are considered as the modulation methods of EFTS. In the cases of the doppler frequency shift of 200Hz present in EFTS using noncoherent DPSK and noncoherent CPFSK are simulated. Simulation results show that $E_b/N_o$ of 0.5dB deteriorates in the region of near BER of about $10^{-5}$ in RS coding. And there is no performance variation in $E_b/N_o$ or $E_b/N_o$ is worsened about 0.1dB in the same BER region for the case of using convolutional and BCH coding. Quadrature detector used in FTS using tone signals is not influenced by the doppler frequency shift.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.1
• /
• pp.23-36
• /
• 2017

Objective: This paper presents a study to evaluate the WBGT index for assessing the effects of a wide range of outdoor weather conditions on human responses. Background: The Wet Bulb Globe Temperature (WBGT) index was firstly developed for the assessment of hot outdoor conditions. It is a recognised index that is used world-wide. It may be useful over a range of outdoor conditions and not just for hot climates. Method: Four group experiments, involving people performing a light stepping activity, were conducted to determine human responses to outside conditions in the U.K. They were conducted in September 2007 (autumn), December 2007 (winter), March 2008 (spring) and June 2008 (summer). Environmental measurements included WBGT, air temperature, radiant temperature (including solar load), humidity and wind speed all measured at 1.2m above the ground, as well as weather data measured by a standard weather station at 3m to 4m above the ground. Participants' physiological and subjective responses were measured. When the overall results of the four seasons are considered, WBGT provided a strong prediction of physiological responses as well as subjective responses if aural temperature, heart rate and sweat production were measured. Results: WBGT is appropriate to predict thermal strain on a large group of ordinary people in moderate conditions. Consideration should be given to include the WBGT index in warning systems for a wide range of weather conditions. However, the WBGT overestimated physiological responses of subjects. In addition, tenfold Borg's RPE was significantly different with heart rate measured for the four conditions except autumn (p<0.05). Physiological and subjective responses over 60 minutes consistently showed a similar tendency in the relationships with the $WBGT_{head}$ and $WBGT_{abdomen}$. Conclusion: It was found that either $WBGT_{head}$ or $WBGT_{abdomen}$ could be measured if a measurement should be conducted at only one height. The relationship between the WBGT values and weather station data was also investigated. There was a significant relationship between WBGT values at the position of a person and weather station data. For UK daytime weather conditions ranging from an average air temperature of $6^{\circ}C$ to $21^{\circ}C$ with mean radiant temperatures of up to $57^{\circ}C$, the WBGT index could be used as a simple thermal index to indicate the effects of weather on people. Application: The result of evaluation of WBGT might help to develop the smart clothing for workers in industrial sites and improve the work environment in terms of considering workers' wellness.

• Journal of dental hygiene science
• /
• v.15 no.5
• /
• pp.536-541
• /
• 2015

The purpose of this study was to evaluate the marginal and internal gap of Cobalt (Co)-Chromium (Cr) sintering metal coping fabricated by dental computer-aided design/computer-aided manufacturing systems. Abutment tooth 46 of universal numbering system was selected for the study. Twenty Co-Cr metal copings of two groups were manufactured and scanned. Co-Cr cast metal copings (CCM) group of ten were fabricated using investment, burnout and casing after subtractive manufacturing of wax block. Also, Co-Cr sintering metal copings (CSM) group of ten were fabricated using sintering processing after subtractive manufacturing of Co-Cr soft metal bock. Marginal and internal gap of Co-Cr metal copings of twenty were measured by digital microscope (${\times}160$) with silicone replica technique. The data was analyzed from IBM SPSS Statistics ver. 22.0 Statistical software for Mann-Whitney U test (${\alpha}=0.05$). $Mean{\pm}standard$ deviation of marginal gap of CCM group was $90.12{\pm}61.73{\mu}m$ of CSM group was $60.17{\pm}24.83{\mu}m$. However, two groups was statistically not different (p>0.05). This study showed that CSM group was clinically acceptable adaptation.

• Journal of Korea Multimedia Society
• /
• v.12 no.7
• /
• pp.989-996
• /
• 2009

Recently, use of the GIS (Geographic Information System) for the disaster of the urban inundation is increasing. The digital disaster map is the system which analyzes the occurrence area of inundation in the past and forecasts the flood areas by the hydrology method. The development of the system which simulates the flood forecast area by the SWMM(Storm Water Management System) and hydrology method and displays the danger areas is required for the construction of the inundation forecast system. And the spatial database which contains information of the urban facilities such as the street and building and the sewer system such as the manhole and drainage and the result of the hydrology analysis is constructed. In this paper, we propose the method for transforming the Shape File in ESRI into the Oracle spatial database to construct the spatial data for the drainage systems and urban facilities using the Shape File format in the ESRI. We suggest the algorithm for the transformation of the data format, and develop the prototype system to display the inundation area using the spatial database.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.30 no.4
• /
• pp.37-46
• /
• 2002

The main purpose of this research is to discuss the urban heat island which will be caused by urbanization, especially by the construction of new town on a wide green zone. Over the last ten years, five new towns have been developed around the Seoul metropolitan area. However these new towns become bedroom communities and create traffic problems between Seoul and its surrounding areas because of an increase in population and a lack of roads and other infrastructures. The construction of another such new town is under consideration in the Pan-gyo area. But it is important that Pan-gyo remains a wide green zone. Many studies show that green space can play an important role in improving urban eco-meteorological, ameliorative capability and air hygiene. The objective of this study is to analyze the urban heat islands of Bund-Dang Si which was constructed in 1996 and of the Pan-Gyo area planned as new town. To investigate the local thermal environment and its negative effects caused by change of the land use type and urbanization we used LANDSAT TM images for extraction of urban surface temperature according to change of land use over 15 years. These data were analyzed together with digital land use and topographic data. As a study result, we found that the thermal island of this area from 1985 to 1999 rapidly increased with a difference of mean temperature of more than 12'E. Before construction of Bun-Dang Si the temperature of this area was the same as the forest, but during the new town construction in 1991, an urban heat island developed. The temperature of forest with a size of over 50% of the investigation area was lowest, which leads us to conclude that the forest cools the urban and its surroundings. The mean temperature of the residential and commercial area is more than +4.5$^{\circ}C$ higher then forest, so this method of land use is the main factor increasing the urban heat island. Urban heat islands and green space play an important role in urban wind systems, i.e. Thermal Induced Air Exchange and Structural Wind Circulation, because of their special properties with regard to energy balance between constructed urban and land. The skill to allocate land use types in urban areas is a very important planning device to reduce air pollution and induce the fresh cold air from green space. An urban climatic experiment featuring a numerical wind simulation study to show the air corridor will be published in a following research paper.