• Journal of the Semiconductor & Display Technology
• /
• v.20 no.3
• /
• pp.18-21
• /
• 2021

This paper analyzes the distortion correction of the in the micro DMD(digital micro mirror device) projector system using 0.25 or less optical throwing distance ratio. The distortion of projected image occurs depending on the performance of the optical lens, the installation location of the projection system, and the tilt of the screen. This study analyzed the physical tilt values influencing of the distortion of projected image, removed the tilt distortion of throwing distance ratio optical lens, and adjusted the distortion image by the simulation of calibration displacements. The results of this study demonstrated within 5% TV distortion reference. Moreover, the correction method reduced the pin-distortion correction of projection system.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.9
• /
• pp.799-805
• /
• 2015

The further development of information, communication and digital media technologies requires the use of advanced, miniaturized semiconductor chips that operate at a high frequency. Die bonding and wire bonding methods for semiconductor packaging have been replaced by direct attachment to the substrate after forming a bump on the chip. However, the height of the bump or ball is an important factor for defects during assembly. This paper proposes an algorithm to measure the height of the bumps or balls in semiconductor packaging with greater accuracy. The performance of the proposed algorithm is experimentally validated. Non-contact 3D measurements of a shiny round ball is quite difficult, and it is not easy to obtain accurate data. This paper thus proposes an optical method and technique to improve the measurement accuracy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.111-116
• /
• 2018

Recently, shape manufacturing method has been changed to a 3D printer. Since lamination type manufacturing method is the basis for forming a three-dimensional shape by repeated lamination, the horizontal accuracy of the lamination layer is very important. In the current paper, we have proposed a new leveling system to be installed in a large 3D printer. The light source was reflected from the water surface contained in the measuring device, and the inclination of the measuring device was measured from the light that entered into four regions of a quarter photodetector. The electrical signals generated differently according to the position of the beam spot incident on the quarter photodetector was acquired and compensated to be horizontal by using a motor mounted at the corner. Compared to a digital leveler, the newly developed leveling system gave errors of only 2 to 3%. This new device can be applied to various fields including the 3D printer in future.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.1009-1012
• /
• 1999

Recently, there is a strong need of DVD (Digital Versatile Disk) system of high density. high speed, and high accuracy System performances mostly depend on not only optical system, but also servo technology to drive it. Therefore, we investigate main technology concerned with optical pick-up unit based on 4.7GB DVD-RAM and analyzes technology of optical and servo systems that are required for high density high speed and high accuracy from the viewpoint of control. And then, we design a linear controller based on specification of 4.7GB DVD-RAM that is commercially available now. We analyze the dynamic characteristics of optical system that is coupled with control system and verify effect on performance indices of servo due to Parameter variation of pick-up by simulation. Finally, we will propose controller design specifications and provide direction of technical development for servo system and problems coupled with high capacity for 15GB level in the future.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.6
• /
• pp.1435-1440
• /
• 2010

This paper presents encrypted secret code recording system which can insert an unique manufacture ID code after complete disc process. First, we detect a memory block synchronizing signal which is SYNC. by using FPGA, then, design a recording pattern to write Multi Pulse. Finally, a method that any data is recorded in any place in any data area of optical disc by using a FPGA was proposed. Newly proposed method in this paper that any user records user data in protected data areas on digital video optical discs, can be very useful for effective software copy protection, and can be applicable to encrypted record on high density DVD in near future.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.323-328
• /
• 2006

A fundamental problem in digital holography is the presence of zero-order noise in the reconstruction process, which decreases the signal to noise ratio(SNR). For many applications, that reduction of SNR makes digital holography impractical, so a great number of approaches have been tested in order to overcome such a problem. In this paper we use the scanning method to suppress the zero-order diffraction noise and the interference noise between object beams. We demonstrate that it is possible to increase the image quality with the scanning method.

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.339-344
• /
• 2001

We propose a method to represent binary data by modulating both the intensity and the phase of uniform plane waves with a twisted-nematic liquid crystal display for holographic digital data storage especially in a disk-shaped recording medium. As far as intensity modulation is concerned, our method is not different from the conventional method, because binary bit values 0 and 1 are represented by the dark (off) and lit (on) states of the liquid crystal display pixels, respectively (or vice versa). With our method, however, the on pixels are also controlled so that the beams passing through them can have one of two different phase delays. If the difference of the two phase delays is close to 180 degrees, we can reduce the dc component of the data image and thus improve the beam intensity uniformity at the holographic recording plane when Fourier plane holograms are recorded. The feasibility of our method is experimentally demonstrated. rated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.9
• /
• pp.1248-1256
• /
• 1993

The propagation and delay properties in opical fiber are particularly attractive because digital signal processing and conventional analog signal processing techniques such as those using surface acoustic wave devices are limited In their usefulness for signal bandwidth exceeding one or two GHz, although they are very effective at lower frequencies. Since an accurate, low loss and short time delay elements can be obtained by using such an optical fiber, optical signal precessing has attracted much attention for high speed and broad-band signal precessing in particular channel separation filtering for optical FDM signals. In this paper, we consider a coherent optical lattice filter, which uses coherent light sources and consists of directional couplers and optical fiber delay elemnts. The optical fiber fitters are more restricted than the usual digital filters. The reasons are as follows. 1) the coupling coefficients of directional couplers are restricted to the number between 0 and 1. 2) optical signal E(complex amplitude) is divided into J If-$\boxUl$ and J L/7$\div$$\boxUl$ at the directional coupler. Considering these restrictions and in this case all the coupling coefficients of summing and branching elements are set to be equal, we have given design formulae for optical lattice filter, which make the best use of optical signal energy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.6C
• /
• pp.604-610
• /
• 2009

This paper propose a digital watermarking method for digital contents which satisfies both the invisibility and the robustness to attacks to prohibit counterfeiting, modification, illegal usage and illegal re-production of video contents. This watermarking algorithm insert a watermark(digital hologram) by generated using Fresnel transform which improve the robustness. The inserting positions of the watermark choose by considering the frequency property of an image and a watermark. Also the amount of watermarking for watermark bit decide by considering the level of 2DDWT. This algorithm was implemented by C++ and experimented for invisibility and robustness with optical system. The experiment results showed that the method satisfied enough the invisibility of the inserted watermark and robustness against attacks. For the general attacks, the error rate of the extracted watermark was less than 15%, which is enough in robustness against the attacks.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.420-429
• /
• 2006

In the zoom lens of digital still cameras with the variation of the image plane generated by various symmetric error factors such as curvature, thickness and refractive index error of each lens surface about the optic axis, we induce a theoretical condition to fix constantly the image plane by translating the compensator group of the zoom lens by using the Gaussian bracket. We confirm the validity of this condition by using three examples of general zoom lens types with 3, 4, and 5 groups, respectively. When these error factors are randomly changed within the range of tolerance according to the Monte Carlo method, we verify that the distributions of the degree of moving of the compensator are normal distributions at three zoom lens types. From capability analysis using these results, we theoretically propose the method estimating the standard deviation, that is, sigma-level, as a function of the maximum movement of the compensator.