• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.55 no.4
• /
• pp.161-166
• /
• 2006

In this paper, an automatic lighting control system is developed using microprocessor. The developed system consists of a digital lighting control unit, an analog lighting control unit, and a lighting control simulator. In the developed system, ATMega128 is used as the main controller. The developed digital lighting control unit consists of eight modules and the developed analog lighting control unit consists of six modules respectively. Additional, the developed simulator consists of a digital and an analog lighting control simulation using graphic user interface. And so this developed system can be applied to the controller design of the interior and exterior lighting equipment.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.563-566
• /
• 2003

We have designed the power control unit which belongs to the power cabinet and controls the power supplied to Control Rod Drive Mechanism(CRDM) as a digital system based on Digital Signal Processor(DSP). The power control unit dualized as the form of Master/Slave has had its increased reality. The Central Process Unit(CPU) board of a power control unit possesses two Digital Signal Processors(DSPs) of the control DSP for performing the tasks of power control and system monitoring and the communication of the Control DSP and the Communication DSP. To accomplish the functions requested in the power control unit effectively, we have installed Field Programmable Gate Arrays(FPGAS) on the CPU board and have FPGAs perform the memory mapping, the generation of each chip selection signal, the giving and receiving of the signals between the power controllers dualized, the fault detection and the generation of the firing signals.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1304-1308
• /
• 2005

This paper presents the case that the existing analog control systems were retrofitted with digital DCS(Distributed Control System)s for boiler unit in thermal power plant. Replacement of existing worn-out or obsolete analog control systems has been considered. Replacement of existing analog control systems with another analog control systems has lots of difficulties in maintaining the systems due to being out of stock. Due to those difficulties, existing analog control systems have been retrofitted with digital DCSs in many industrial sites. KEPRI(Korea Electric Power Research Institute) accomplished the project that retrofitted analog control systems with the developed DCSs for boiler unit in middle-scale coal-fired thermal power plant. The benefits of an upgrade to digital control include a increase of reliability due to system redundancy, ease of modifying the control logic and the parameters of function block, ease of maintenance due to available spare parts, improvement of information display, ease of modifying MMI(Man Machine Interface) displays, a increase in system availability, and improvement of control performance. This paper describes how to use the parameters of existing analog controllers, the implementation of digital PID controller, control system configuration for boiler unit in thermal power plant, some boiler control loops, control result during commissioning, and the comparison of boiler characteristic test data after retrofitting with the existing test data.

• Journal of Power Electronics
• /
• v.8 no.2
• /
• pp.121-130
• /
• 2008

This paper introduces a design and implementation of a digital control unit for an Oxygenaire Servo Baby Incubator. The control unit is designed and implemented according to international standards. The control unit is based on an AVR Atmel microcontroller unit. It is built for monitoring and control and displays the three main temperature values: set point temperature, baby skin temperature and air temperature. User friendly software is implemented. The implemented control unit was tested in the laboratory as well as in the field. The control unit is sensitive to change of $0.1^{\circ}C$. At startup, based on a unique control strategy, the incubator reaches its steady state in about 14 minutes. The system schematic diagrams are shown in the paper. Also, programs flow charts are presented. The control unit was designed and implemented based on a contract between the Electronics Research Institute (ERI) and ENGIMED Company. The authors would like to thank ERI and ENGIMED for introducing all required finance and shoring to complete this work.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.498-503
• /
• 2005

As important device that decide output load in superannuated thermoelectric power plant which do Turbine Load Set Motor device. This generation of electric power system operated Set Up Range Motor according to Set Up value that operator manufactures by hand circumvolve, and generation of electric power output load derision is consisted by internal action including Motor Therefore, in this research passively output load operated Turbine Motor Drive equipment that can have existing Turbine Load Set Motor Performance developing Digital Drive Unit device design. Also control algorithm implementation and existing Turbine Load Set Motor Drive and connection possibility through designed controlling system to connect basis function that decide development output load with Digital Drive Unit that designed also with existing Motor Drive Unit and can be operated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.2
• /
• pp.63-70
• /
• 2003

In this paper, an MFC (Mass Flow Controller) which is widely used in many semiconductor manufacturing processes for controlling the mass flow rate of a gas is designed and implemented using the PIC 16F876 of Microchip, Inc. The MFC implemented in this thesis has the form of hybrid-type, i.e., the mixed-type of the analog-type MFC, which has many problems such as low accurary, and digital-type MFC, which use an expensive DSP (Digital Signal Processor) and an ADC (Analog to Digital Convertor) with high precision. The MFC is consists of the sensor unit, the control unit and the actuator unit, and it has used the automatic calibration algorithm and the reference table method for the improvement of the performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.2003-2008
• /
• 2012

A drive system is necessary to operate LED by an LED illumination system. Because Switched Mode Power Supply (SMPS) is higher in efficiency in the large capacity than Linear Regulator, it is used mainly and controls this in an analog form or digital method. A MCU and a DSP of the digital control central processing unit were higher in a unit price than existing analog control chip, so that an approach was not easy for application of SMPS. But it can take the earnings by it lets you integrate various digital control features like an LED illumination system in one MCU, and realizing a whole system. In this paper, we suggest the algorithm that can improve LED driving current in applying such a digital control method using low-priced type MCU.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.167-169
• /
• 2010

Electronic control units for propulsion systems are devices which compute control algorithm by processing the systems' internal sensor signals. Due to the effect of transmission between sensors and a control unit, previous analog systems have drawbacks of signal attenuation and susceptibility to noises. However, a digital sensor can be less influenced by the electrical cable line as it includes sensor, AMP, and AD converter in one module. In addition, it can reduce the process time for control algorithm because extra S/W filtering process is not needed. The current study shows how to process signals for an electronic control unit using digital sensors.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.1
• /
• pp.55-60
• /
• 2014

Today, there is increasing the elderly population in rural community, and people of returning from the urban to the rural community are demand to be of high value-added agriculture. In this time, there are required to regularization, standardization, automation, for getting of production of high value crops. In this paper, we are study for automation cultivation control system design for produce high-value crops. this system were designed of two parts that one part is measure and control unit, another part is server part for database and server side control. the main controller for measurement and control is used MC9S08AW60, server for Database and server-side control was using MySQL with CentOS. The source code of control program was coding C and compile with GCC. the functions of measurement and control unit are digital input and output each 8channels and can be scan-able of 20 Bit with 2CH/Sec. Analog Output were designed that can be output of 4-20mA or 0-5V on 4channel. The Digital input and output part were designed 8-channel, and using the high speed photo coupler and relays. We showed that system is possible to measure a 20bit data width, 2Ch/sec as 8 channel analog signals.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.57-61
• /
• 2006

As high speed internet users are tremendously increasing, three are keenly in need of development of high speed portable internet technology which can provide high quality wireless internet service cheaply even in the mobile. Unlike the FDD-CDMA, TDD-OFDMA has relatively poor wave environment with inducing interference, fading and delay because it agrees to multi-carrier modulation method and time-division radio telecommunication system. To solve this problem, it is necessary to develop repeater operating by digital signal processing method which have more strict wireless channel control and wave signal processing technology over TDD telecommunication equipments. This thesis is dealing with design and implementation of Digital RF Repeater which implemented 'Synchronization Acquisition Unit', 'TDD signal switching Unit', 'Feedback Signal Cancellation Unit'. Over this argument, we will develop digital RF repeater with more cheap, more adaptive in wave environment like oscillation control, adaptive wave monitoring and output increasing and having control function as a result it will be helpful for success in high speed portable internet service business.