• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.4
• /
• pp.187-191
• /
• 2004

In this work, we used the PCID simulator for simulation of solar cell and examined the effect of front-back surface recombination velocity, minority carrier diffusion length, junction depth and emitter sheet-resistance. As the effect of base thickness, the efficiency decreased by the increase in series resistance with the increase of the thickness and found decrease in efficiency by decrease of the current as the effect of the recombination. Also, as the effect of base resistivity, the efficiency increased somewhat with the decrease in resistivity, but when the resistivity exceeded certain value, the efficiency decreased as a increase in the recombination ratio. The optimum efficiency was obtained at the resistivity 0.5 $\Omega$-cm, and thickness $100\mu\textrm{m}$. We have successfully achieved 10.8% and 13.7% efficiency large area($103mm{\times}103mm$) mono-crystalline silicon solar cells without and with PECVD silicon nitride antireflection coating.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.3
• /
• pp.209-213
• /
• 1994

Two unknown values among three electrochemical values, i.e. electrode area, diffusion coefficient, and concentration, are simultaneously obtained by nonlinear regression analysis of a single chronoamperometric faradaic current curve at a microdisk electrode. The approach is an analytical application of the semi-empirical equation presented by Shoup and Szabo for the chronoamperometric response at a disk electrode. To demonstrate the usefulness and accuracy of this approach, the chronoamperometric current at a platinum disk electrode of 50 ${\mu}m$ radius in solutions of $Ru(NH_3)_6^{3+},\;ferrocene,\;Fe(CN)_6^{3-},\;and\;C_{60}$, were analyzed.

• Design & Manufacturing
• /
• v.15 no.2
• /
• pp.49-55
• /
• 2021

In this study, CALPUFF, a three-dimensional atmospheric diffusion model, was used to predict the degree of influence of pollutants generated during clean center operation on surrounding areas. To drive the CALPUFF model, CALMET, a weather field calculation model, was used. Due to the influence of the wind field, air pollutants from the Clean Center diffused in the southeast direction, increasing the distribution area. SOx satisfies atmospheric environmental standards with an annual average value of 0.02 ppm or less NOx satisfies atmospheric environmental standards with an annual average value of 0.03 ppm or less. Dust (PM-10) satisfies atmospheric environmental standards with an annual average value of 50㎍/m³ or less and 24 hours average value of 100㎍/m³ or less. CO satisfies atmospheric environmental standards with an 8 hours average value of 9 ppm or less and an 1 hour average value of 25 ppm or less.

• International Journal of Computer Science & Network Security
• /
• v.22 no.6
• /
• pp.91-96
• /
• 2022

The photocatalytic degradation of salicylic acid takes place in several stages involving coupled phenomena, such as the transport of molecules and the chemical reaction. The systems of transport equations and the photocatalytic reaction are numerically solved using COMSOL Mutiphysics (CM) simulation software. CM will make it possible to couple the phenomena of flow, the transport of pollutants (salicylic acid) by convection and diffusion, and the chemical reaction to the catalytic area (bauxite or TiO2 doped by nanoparticles). The simulation of the conversion rate allows to correctly fit the experimental results. The temporal simulation shows that the reaction reaches equilibrium after a transitional stage lasting over one minute. The outcomes of the study highlight the importance of diffusion in the boundary layer and the usefulness of injecting micro-agitation into the microchannel flow. Under such conditions, salicylic acid degrades completely.

• Journal of Environmental Science International
• /
• v.1 no.1
• /
• pp.35-43
• /
• 1992

Handling the emergency problems such as Chemobyl accident require real time prediction of pollutants dispersion. One-point real time sounding at pollutant source and simple model including turbulent-radiation process are very important to predict dispersion at real time. The stability categories obtained by one-dimensional numerical model (including PBL dynamics and radiative process) are good agreement with observational data (Golder, 1972). Therefore, the meteorological parameters (thermal, moisture and momentum fluxes; sensible and latent heat; Monin-Obukhov length and bulk Richardson number; vertical diffusion coefficient and TKE; mixing height) calculated by this model will be useful to understand the structure of stable boundary layer and to handling the emergency problems such as dangerous gasses accident. Especially, this simple model has strong merit for practical dispersion models which require turbulence process but does not takes long time to real predictions. According to the results of this model, the urban area has stronger vertical dispersion and weaker horizontal dispersion than rural area during daytime in summer season. The maximum stability class of urban area and rural area are "A" and "B" at 14 LST, respectively. After 20 LST, both urban and rural area have weak vertical dispersion, but they have strong horizontal dispersion. Generally, the urban area have larger radius of horizontal dispersion than rural area. Considering the resolution and time consuming problems of three dimensional grid model, one-dimensional model with one-point real sounding have strong merit for practical dispersion model.al dispersion model.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.1
• /
• pp.73-84
• /
• 2006

Hazardous Air Pollutants (HAPs) are characterized by being relatively heavier and denser than that of ambient air due to the various reasons such as higher molecular weight, low temperature and other complicated chemical transformations (Witlox, 1994). In an effort to investigate transport and diffusion from instantaneous emission of heavy gas, Lagrangian Particle Dispersion Model (LPDM) coupled with the RAMS output was employed. Both deposition process and buoyancy term were added on the atmospheric diffusion equations of LPDM, and the locations and concentrations of dense gas particle released from instantaneous single point source (emitting initially for 10 minutes only) were analyzed. The result overall shows that adding deposition process and buoyancy terms on the diffusion equation of LPDM has very small but detectable effect on the vertical and horizontal distribution of Lagrangian particles that especially transported for a fairly long traveling time. Also the slumping of dense gas can be found to be ignored horizontally compared to the advection by the horizontal wind suggesting that it was essential to couple the Lagrangian particle dispersion model coupled with the RAMS model in order to explain the dispersion of HAPs more accurately. However, during the initial time of instantaneous emission, buoyancy term play an important role on the vertical locations of dense particles for near surface atmosphere and around source area, indicating the importance of densities of HAPs in the beginning stage or short duration for the risk assessment of HAPs or management of heavy vapors during the explosive accidents.

• The Journal of the Korea Contents Association
• /
• v.10 no.10
• /
• pp.389-397
• /
• 2010

This study is to find out influences of IT innovations factors on e-commerce diffusion, management performance. To research and analyze, from August 15th to September 15th in 2009, the questionary distributed 150 working employees at Purchasing Team & Finance Team in five star hotel in Seoul Metropolitan Area, then used for data analysis 135. The results come up with; Firstly, the factors of Information Techonology impacted on e-commerce diffusion & management performance. Secondly, e-commerce diffusion within company only had effect on management performance. The implication of this study is that if IT innovation factors were improved, hotels would have competitive achievement.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.6
• /
• pp.87-94
• /
• 2007

This study used POM (Princeton ocean model) improved for applying to coastal area in order to predict the distribution of thermal waste water. This model was applied to the coastal circulation and the effect of thermal waste water of Cheonsu-Bay. So this study compared the discharge of thermal waste water with each layer and section. The tidal current was about 1.5 m/sec at surface level and 0.9 m/sec on bottom level at flood tide; tidal current was about 1.3 m/sec on surface level and 0.8 m/sec on bottom level at ebb tide. The method discharging the thermal waste water in the nearshore region (case 1) accelerates the diffusion of the thermal waste water in the north-south direction(longshore direction). However, the method discharge the thermal waster water in the offshore region (case 2) reduced the diffusion of the thermal waste water over the coastal region. According th the diffusion region of the thermal waste water with case 1 and case 2 at three different layers (surface, middle, bottom), the diffusion region by case 1 discharge method generally influenced wider region (twice) than the one by case 2 discharge method with lower temperature between $1^{\circ}C\;and\;2^{\circ}C$, whereas the case 2 discharge method influenced the deeper region (middle and botton layers) with higher change of the water temperature ($1{\sim}3^{\circ}C$).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.466-473
• /
• 2017

RC (Reinforced Concrete) member has varying service life due to varying diffusion characteristics with loading conditions even if it is exposed to constant exterior conditions. In the paper, quantitative parameters are obtained through adopting the previous results for effects of compressive, tensile, and cold joint on chloride diffusion in OPC (Ordinary Portland Cement) and GGBFS (Ground Granulated Blast Furnace Slag) concrete. Service life is evaluated in RC simple beam with 10.0m of span through increasing loading from self weight (2.5kN/m) to the loading to cracking moment (5.5kN/m). In OPC concrete without cold joint, service life changes to 89.4% for tensile region and 101% for compressive region with loadings while GGBFS concrete has 80.0% and 106%, respectively. For cold joint area, GGBFS concrete shows much reduced service life to 82~80% in compressive region and 69~61% in tensile region, which is caused by the lower diffusion in normal condition but relatively higher increasing cold joint effect than OPC concrete.

• Tunnel and Underground Space
• /
• v.17 no.5
• /
• pp.372-380
• /
• 2007

Surface damage due to subsidence is an inevitable consequence of underground mining, which may be immediate or delayed for many years. The surface damage due to abandoned underground mine is observed to be two subsidence types such as simple sinkhole or trough formation to a large scale sliding of the ground from with in the subsided area. An evaluation of the risk of a subsidence occurrence is vital in the areas affected by mining subsidence. For a subsidence prediction or a risk evaluation, there has been used various methods using empirical models, profile functions, influence functions and numerical models. In this study, a simple but efficient evaluation method of subsidence hazard is suggested, which is based on a diffusion theory and uses just information about geometry of caving and topography. The diffusion model has an analogous relationship with granular model which can explain a mechanism of subsidence. The diffusion model is applied for the evaluation of subsidence hazard in abandoned metal and coal mines. The model is found to be a simple but efficient tool because it needs information of geometry of caving and gangway and the topography.