• ETRI Journal
• /
• v.42 no.5
• /
• pp.773-780
• /
• 2020

A 40 nm complementary metal oxide semiconductor carrier-aggregated drive amplifier with high linearity is presented for sub-GHz Internet of Things applications. The proposed drive amplifier consists of two high linear amplifiers, which are composed of five differential cascode cells. Carrier aggregation can be achieved by switching on both the driver amplifiers simultaneously and combining the two independent signals in the current mode. The common gate bias of the cascode cells is selected to maximize the output 1 dB compression point (P1dB) to support high-linear wideband applications, and is used for the local supply voltage of digital circuitry for gain control. The proposed circuit achieved an output P1dB of 10.7 dBm with over 22.8 dBm of output 3rd-order intercept point up to 0.9 GHz and demonstrated a 55 dBc adjacent channel leakage ratio (ACLR) for the 802.11af with -5 dBm channel power. To the best of our knowledge, this is the first demonstration of the wideband carrier-aggregated drive amplifier that achieves the highest ACLR performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.22-26
• /
• 2012

This paper introduces a 2.5-Gb/s optical receiver implemented in a standard 1P4M 0.18um CMOS technology for the applications of active optical HDMI cables. The optical receiver consists of a differential transimpedance amplifier(TIA), a five-stage differential limiting amplifier(LA), and an output buffer. The TIA exploits the inverter input configuration with a resistive feedback for low noise and power consumption. It is cascaded by an additional differential amplifier and a DC-balanced buffer to facilitate the following LA design. The LA consists of five gain cells, an output buffer, and an offset cancellation circuit. The proposed optical receiver demonstrates $91dB{\Omega}$ transimpedance gain, 1.55 GHz bandwidth even with the large photodiode capacitance of 320 fF, 16 pA/sqrt(Hz) average noise current spectral density within the bandwidth (corresponding to the optical sensitivity of -21.6 dBm for $10^{-12}$ BER), and 40 mW power dissipation from a single 1.8-V supply. Test chips occupy the area of $1.35{\times}2.46mm^2$ including pads. The optically measured eye-diagrams confirms wide and clear eye-openings for 2.5-Gb/s operations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.8-18
• /
• 2007

In this paper, a 4bit cell way structure of PoRAM and the sensing method to drive this structure are researched. PoRAM has a different operation from existing SRAM and DRAM. The operation is that when certain voltage is applied between top electrode and bottom electrode of PoRAM device we can classify the cell state by measuring cell current which is made by changing resistance of the cell. In the decoder selected by new-addressing method in the cell array, the row decoder is selected "High" and the column decoder is selected "Low" then certain current will flow to the bit-line. Because this current is detect, in order to make large enough current, the voltage sense amplifier is used. In this case, usually, 1-stage differential amplifier using current mirror is used. Furthermore, the detected value at the cell is current, so a diode connected NMOSFET, that is, a device resistor is used at the input port of the differential amplifier to converter current into voltage. Using this differential amplifier, we can classify the cell states, erase mode is "Low" and write mode is "High", by comparing the input value, Vin, that is a product of current value multiplied by resistor value with a reference voltage, Vref.

• Journal of information and communication convergence engineering
• /
• v.9 no.1
• /
• pp.11-15
• /
• 2011

A Differential line inductor is proposed for a differential power amplifier. The proposed differential line inductor is composed of two conventional line inductors rearranged to make the current direction of the two line inductors identical. The proposed line inductor is simulated with a 2.5-D and a 3-D EM simulator to verify its feasibility with the substrate information in a 0.18-${\mu}m$ RF CMOS process. The inductances of various line inductors implemented with printed circuit boards were measured. The feasibility of the proposed line inductor was successfully demonstrated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.12-22
• /
• 1999

Operation of an electromagnetic shaker system using a Class-D amplifier may cause unacceptable electromagnetic interference to another electronic system, requiring the user to take whatever steps are necessary to correct the interference. A differential amplifier in a Class-D amplifier is used to decrease the effect of a common-mode noise voltage in a shaker system. To prevent a ground loop, a transformer is inserted in another shaker system. These methods show reduction of the unwanted vibration which has occurred before. A transformer in a charge amplifier was used to prevent a ground loop in a shaker system using a Class-AB amplifier a few years ago, but it was susceptible of noise in a shaker system using a Class-D amplifier. Hence we corrected a ground loop between a charge amplifier and a vibration control/analysis system without a transformer. The usefulness of this approach is illustrated by the results of experiments.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.3
• /
• pp.53-59
• /
• 1994

A new fully differential sample-and-hold circuit which can effectively compensate the offset voltage of an operational amplifier and the charge injection of a MOS switch is presented. The proposed circuit shows a true sample-and-hold function without a reset period or an input-track period. The prototype fabricated using a 1.2$\mu$m double-polysilicon CMOS process occupies an area of 550$\mu$m$\times$288$\mu$m and the error of the sampled ouput is 0.056% on average for 3V input at DC.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.91-95
• /
• 2008

This paper presents a direct-conversion I/Q up-mixer block, which supports $3{\sim}5$ GHz ultra-wideband(UWB) applications. It consists of a VI converter, a double-balanced mixer, a RF amplifier, and a differential-to-single signal converter. To achieve wideband characteristics over $3{\sim}5$ GHz frequency range, the double-balanced mixer adopts a shunt-peaking load. The proposed RF amplifier can suppress unwanted common-mode input signals with high linearity. The proposed direct-conversion I/Q up-mixer block is implemented using $0.18-{\mu}m$ CMOS technology. The measured results for three channels show a power gain of $-2{\sim}-9$ dB with a gain flatness of 1dB, a maximum output power level of $-7{\sim}-14.5$ dBm, and a output return loss of more than - 8.8 dB. The current consumption of the fabricated chip is 25.2 mA from a 1.8 V power supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.54-62
• /
• 1999

In this paper, we investigated the signal-to-noise ratio improvement in a differential detector, which is a function of the optical noise coupling ratio and the differential gain ratio. A differential detector consists of two photodiodes and a differential amplifier. The differential detector reduced the noise component and improved the signal-to-noise ratio by about 20 dB when the differential gain ratio equals to the optical noise coupling ratio. The differential detector is very effective in removing the environmental optical noise or interference from an adjacent optical channel. This method is also effective when the noise wavelength is similar to the signal.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.4
• /
• pp.566-570
• /
• 2008

Vertical nanowire SGFETs(Surrounding Gate Field Effect Transistors) provide full gate control over the channel to eliminate short channel effects. This paper presents design and characterization of a differential pair amplifier using NMOS and PMOS SGFETs with a 10nm channel length and a 2nm channel radius. The amplifier dissipates $5{\mu}W$ power and provides 5THz bandwidth with a voltage gain of 16, a linear output voltage swing of 0.5V, and a distortion better than 3% from a 1.8V power supply and a 20aF capacitive load. The 2nd and 3rd order harmonic distortions of the amplifier are -40dBm and -52dBm, respectively, and the 3rd order intermodulation is -24dBm for a two-tone input signal with 10mV amplitude and 10GHz frequency spacing. All these parameters indicate that vertical nanowire surrounding gate transistors are promising candidates for the next generation high speed analog and VLSI technologies.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.4
• /
• pp.461-466
• /
• 1999

A CMOS op amp with rail-to-rail input and output ranges is designed in a one-volt supply. The output stage of the op amp is used in a common source amplifier that operates in sub-threshold region to design a low voltage op amp with rail-to-tail output range. To drive heavy resistor and capacitor loads with rail-to-rail output ranges, a common source amplifier which has a low output resistance is utilized. A bulk-driven differential pair and a bulk-driven folded cascode amplifier are used in the designed op amp to increase input range and achieve 1 V operation. Post layout simulation results show that low frequency gain is about 58 ㏈ and gain bandwidth I MHz. The designed op amp has been fabricated in a 0.8${\mu}{\textrm}{m}$ standard CMOS process. The measured results show that this op amp provides rail-to-rail output range, 56㏈ dc gain with 1 MΩ load and has 0.4 MHz gain-bandwidth with 130 ㎊ and 1 kΩ loads.