• 전기학회논문지
• /
• 제58권12호
• /
• pp.2396-2401
• /
• 2009

The three-phase buck-boost DC-AC inverter generates three alternating output voltages as the differential voltage of three DC-DC individual buck-boost converters. Three converters are driven with three DC-biased and 1200 phase-shifted sinusoidal references. The peak value of the inverter alternating output voltage can be larger or smaller than the value of the direct input voltage. In this paper, a three-phase buck-boost DC-AC inverter is designed and implemented on a prototype with digital controller using a microcontroller.

• 한국통신학회논문지
• /
• 제13권5호
• /
• pp.422-428
• /
• 1988

반복 학습제어시스템은 시행을 반복함으로써 유한시간의 목표출력에 대하여 추종해 가도록 하는 것이다. 본 논문에서는 이산시간 시스템에 있어서의 이산 시간 학습제어 입력을 구하는 방법을 제안한다. 여기서 현재시행의 제어입력은 바로 전시행에서 입력 sequence와 time-shift된 error sequence의 선형조합에 의하여 구해진다. 컴퓨터로 제어되는 이산시간 시스템에서 error신호의 미분조작이 필요한 연속시간 Betterment Process에 비하여 error sequence의 time-shift조작은 보다 간단해지며 컴퓨터 시뮬레이션을 통하여 그 유효성을 확인하였다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권9호
• /
• pp.650-656
• /
• 2004

This paper presents block and timing diagrams of the DWA(data weighted averaging) to optimize a feedback time delay of the sigma-delta modulator. Through the Matlab modeling, the optimized coefficients of the integrators are obtained to design the modulator. And then the fully differential SC integrators, feedback DAC, 9-level quantizer, and DWA are designed by considering the nonideal characteristics of the modulator. The designed second-order multibit modulator is fabricated in a 0.35$\mu\textrm{m}$ CMOS process. The designed modulator achieves 73dB signal-to-noise ratio and 72dB dynamic range at 1.2Vp-p 585kHz input singal and 52.8MHz sampling frequency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전력기술부문
• /
• pp.50-52
• /
• 2002

Distance relays need accurate current and voltage for determining the trip ignition. Therefore we must analyze nonlinear phenomena which cause distortion in signals first of all. This paper presents the effect of some distortion(arcing fault and current transformer saturation) in power system. The saturation of a current transformer distorts input current of a distance relay and arcing faults make current and voltage to be changed. This paper describes modeling methods of a current transformer and arcing faults, and describes the simulation result of two distance relay algorithms (discrete fourier transform and modified differential equation methods)

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.67-67
• /
• 2000

In this paper, a hybrid type fuzzy controller is proposed to maintain molten steel level stable and reliable manner in high speed continuous casting regardless of various disturbances such as casting speed change, tundish weight variation, 치ogging/undoning of SEN(Submerged Entry Nozzle), periodic bulgings, etc. To accomplish this purpose, hardware filter and software filer are carefully designed to eliminate high frequency noise and to smooth input signals from harsh environments. In order to minimize the molten steel level variations from various disturbances the controller uses hybrid type control term: fuzzy logic term, proportional term, differential term and nonlinear feedback compensation tenn. The proposed controller is applied tn commercial mini-mill plant and shows considerable improvement in minimizing the molten steel variation.

• 한국컴퓨터산업학회논문지
• /
• 제8권2호
• /
• pp.123-130
• /
• 2007

본 논문에서는 신호조정 회로로서 필수적인 다중 채널 심장 전기도 전치 증폭기를 제작하기 위한 설계조건의 분석 및 전기 회로적 해석을 수행하였다. 설계된 회로는 기존의 64 채널의 공간 분해능을 향상시키기 위하여 128채널로 구성하였으며, 전치증폭기는 입력회로부, 차동증폭부, 오른다리구동회로 및 주증폭기의 노치필터로 구성되도록 설계하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.167-171
• /
• 2006

The previous models for thermal behavior in the melting furnace were deterministic, composed of such a form that if the initial input conditions are determined, the results would have been come out by using the basic heat equilibrium equations. But making the experiment by trusting the analysis results, the melted slag is fortuitously set often, because temperature variation of the melted slag in the reaction process is not point function but path function. So in this study, a transient model was developed and verified by comparing with the experimental results.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제50권11호
• /
• pp.550-556
• /
• 2001

The computerized cardiac analysis system, which acquires and analyzes the electrical activation signal propagating along the surface of the heart, is indispensible equipment for the open heart surgery and electrical cardiac study. In this paper, the design requirement and the electrical circuit analysis are performed to construct the multi-channel cardiac activation pre-amplifier necessary for a signal conditioning circuit. The general 64 channel configuration is expanded into 128 channels to enhance the spatial resolution on the mapped surface of the heart. The 128 channels pre-amplifier consists of input circuit, differential amplifier, right leg driven circuit and isolation part. It has distinct features; high voltage protection, leakage current limitation, isolation and the maximization of common mode rejection ratio with respect to the half-cell potential difference due to different electrode materials. The final pre-amplifier circuit is assembled with 8 boards, each of which composing of 16 channels.

• Wind and Structures
• /
• 제3권2호
• /
• pp.117-132
• /
• 2000

Under special conditions of turbulent wind, suspension and cable-stayed bridges could reach instability conditions. In various instances the bridge deck, as like a bluff body, could exhibit single-degree torsional instability. In the present study the turbulent component of flow has been considered as a solution of a differential stochastic linear equation. The input process is represented by a Gaussian zero-mean white noise. In this paper the analytical solution of the dynamic response of the bridge has been determined. The solution has been obtained with a technique of closing on the order of the moments.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1995년도 춘계학술대회
• /
• pp.68-70
• /
• 1995

A low-noise pre-amplifier is developed for use in Topographic Brain Mapping system. It consists of signal generator, signal amplifier with a impedance converter, shield driver, body driver, differential amplifier, and isolation amplifier. Pre-amplifier circuit is designed with the concept of isolation and active body and shield driver. This amplifier shows the good noise behavior, high CMRR, high input impedance, low leakage current and high IMRR.