• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.153-159
• /
• 2007

The performance of a direct-injection type diesel engine often depends on the strength of air flow in the cylinder, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the process of combustion in the cylinder was affected by the mixture formation process. In the present paper, high speed photography was employed to investigate the effectiveness of holes penetrated from the bottom of cavity wall to piston crown for some more useful utilization of air. The holes would function to improve mixing of fuel and air by the increase of air flow in the cylinder. The results obtained are summarized as follows, (1) Activated first of the combustion by shorten of ignition timing and rapid flame propagation (2) Raised the combustion peak pressure, more close to TDC the formation timing of peak pressure.

• 한국분무공학회지
• /
• 제11권4호
• /
• pp.244-250
• /
• 2006

Of the macroscopic spray characteristics of non-reacting diesel fuel sprays, the spray angle reflects directly the atomization and air entrainment processes downstream the nozzle. In addition, spray angle is important because it will be closely related to the spray penetration. The existing definitions for the measurement of spray angle as well as the correlations for the prediction of spray angle are, therefore, summarized and reviewed. The existing definition of spray angle can be classified into four groups: distance based on orifice diameter, distance based on spray tip penetration, definition based on surface wave, and definition based on atomization. It is strongly required to specify the definition and measurement method when the data for spray angle is reported. The existing correlations for spray angle can be classified into two groups: theoretical and empirical correlations. The study on the evaluation of the existing correlations fer spray angle is required.

• 한국해양공학회지
• /
• 제10권4호
• /
• pp.128-140
• /
• 1996

To analyze a formation process of the soots in spray flame in the combustion chamber, an optically accessible DI Diesel engine was used for visualization. The images of the flames and soots were visualiaed with high speed camera by Schlieren method and Light extinction method. The spray flame and soot images on the films were analyzed at the various engine operating conditions. Soot distributed widely in spray flame and its concentration was about $100g/m^3$ at the position close by nozzle tip of spray flame region, however it decreased below $20g/m^3$ at the corner of combustion chamber due to soot oxidation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.43-52
• /
• 2000

In this study, a simulation program was developed, which could simulate a fuel injection system for low-speed marine diesel engine. The fuel injection system was divided into fuel injection pump, high pressure pipe and fuel injection valve. The unsteady flow in the high pressure injection pipe was analyzed by the method of characteristics, considering cavitation and variation of fuel density and bulk modulus. It was confirmed that the simulation results were good agree with experimental results of injection pressure and quantity at the high pressure distributor in fuel injection system for the training ship "M/V Hannara". And the effects of the atomizer hole diameter, maximum needle lift, plunger diameter and nozzle opening pressure were also investigated with simulating results.g results.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.865-876
• /
• 2004

A new concept of reduced quasi-dimensional combustion model for a direct injection diesel engine is developed based on the previously developed quasi-dimensional multi-zone model to improve the computational efficiency. In the reduced model, spray penetration and air entrainment are calculated for a number of zones within the spray while three zones with aggregated spray zone concept are used for the calculation of spray combustion and emission formation processes. It is also assumed that liquid phase fuel appears only near the nozzle exit during the breakup period and that spray vaporization is immediate in order to reduce the computational time. Validation of the reduced model with experimental data demonstrated that the new model can predict engine performance and NO and soot emissions reasonably well compared to the original model. With the new concept of reduced model, computational efficiency is significantly improved as much as 200 times compared to the original model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.448-452
• /
• 2008

2-stroke marine diesel engine has generally one exhaust valve and three fuel injection nozzle which are key component for engine's performance and combustion. Fuel injection and exhaust valve driving system are driven by rotating of camshaft. Rotation of crank shaft drives the cam shaft through gear train that is composed of $3{\sim}4$ gear wheels. Gear column supporting the gear wheel has to bear against the dynamics forces by engine running as well as gearing forces. In this paper, structural analysis for engine structure and fatigue strength assessment of welded joint is shown. Repeatedly full cyclic simulation during one cycle is performed to investigate the structural behavior of engine. Fatigue analysis is carried out based on IIW using submodeling technique to obtain more detailed stress distribution.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.80-86
• /
• 2002

A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozzle hole, diameters of an injection pipe, and injection timing in the fuel injection system. We have obtained the results that the fuel consumption ratio is reduced and NOx concentration is increased as the smaller diameter of injection nozz1e hole, the smaller diameter of injection pipe, and more advanced injection timing. They show that optimizing the factors of fuel injection system is significant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.235-241
• /
• 2002

The process of energy separation in a low pressure vortex tube with air as a working medium is studied In detail. Experimental data of the temperature of the cold and hot air leaving the vortex tube are presented. The variation of the maximum wall temperature along the inner surface of the vortex tube and the temperature distribution in the vortex tube provides useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. In this study Outer tube is used for the application of Diesel engine exhaust. The hot gas flow is fumed 180° and passes the outside of the vortex tube a second time heating it. From this geometric setup of a vortex tube the effects of energy separation and the prediction of the ignition of Diesel Soot is presented by experimental data.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.41-44
• /
• 2015

Experimental study was conducted to investigate the effect of ultra-high injection pressure on combustion and emission characteristics in a single-cylinder diesel engine. Electronically controlled ultra-high pressure fuel injection system consistently supplied the fuel of ultra-high pressure up to 250 MPa. Various injection pressures, 40 to 250 MPa, were applied and compared. A injector with eight identical nozzle holes which have diameter of $105{\mu}m$ was used. The results showed high potential to improve the nitrogen oxide (NOx) and particulate matter (PM) trade-off relationship with an ultra-high injection pressure and the exhaust gas recirculation (EGR).

• 수산해양기술연구
• /
• 제19권1호
• /
• pp.40-45
• /
• 1983

전자식전발분사노즐로 급속압축장치 내에서 실현한 축대칭 자유분무.화염에 고속도 사진의 화상해석을 적용하여 다음과 같은 결론을 얻었다. 1. 고속도 사진의 화상해석에 의해 구한 디이젤분무의 축방향의 연료농도분포는 분무의 선단부를 제외하면 준정상이론에 의한 분포와 정성적으로 일치한다. 2. 화염중심축방향의 그을음 농도는 연과의 농도가 비교적 낮은 분무의 선단부에서 높은 농도를 나타내며, 그 농도는 거의 분사종료시에 최대로 되어, 그 후 시간경과에 따라 저하한다. 3. 양파모델을 축대칭 분무.화염에 적용하여 분무.화염내부의 반경방향의 그을음 농도와 연료농도분포를 비교해 보면 그을음 농도의 가장 높은 부분은 연료농도가 가장 높은 중심부보다 화염반경의 2/3의 위치에서 최대로 되었다