• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.2
• /
• pp.221-227
• /
• 2016

The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts.

• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.214-221
• /
• 2011

In recent years, automotive seat components have been manufactured by the fine blanking process, allowing an improvement of dimensional accuracy at sheared surface in series production. However, the rollover has increased and die failures have occurred more frequently when manufacturing gears by fine blanking. Consequently, important goals for manufacturing seat recliner parts with gears have been to decrease the rollover as well as to improve the tool life. In this study, the half blanking and shaving processes were introduced to improve aforementioned problems for the lower tooth, the main component of a seat recliner. For this purpose, the half blanking process was optimized using the finite element (FE) analysis and design of experiment (DOE). The optimized conditions resulting from this study were an offset of 0.2 mm, a clearance of 0.1 mm and a penetration depth of 4.5 mm. Fine blanking experiment conducted under the optimal condition resulted in a rollover depth decrease from 1.9 to 1.3 mm, and no die failure occurrence.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.338-344
• /
• 2016

The study is actively being performed to increase fuel injection pressure of common rail system among countermeasures to meet the emission regulation strengthen of the Diesel engine. The common rail fuel injection tube in such ultra high pressure common rail system has the weakest structural characteristics against vibration that is generated by fuel injection pressure and pulsation during engine operation and driving. Thus the extreme durability is required for common rail fuel injection tube, and the drawing process is being magnified as the most important technical fact for strength of seamless pipe that is the raw material of common rail tube. In this respect, we analyzed the characteristic of dimension and stress variation of the ultra high pressure common rail fuel injection tube by variation of Die and Plug angle in drawing process. Based on the analysis, we tried to obtain the raw material strength of common rail fuel injection tube for applying to the ultra high pressure common rail system. As a result, Plug angle is more important than entry angle of Die and we could obtain the target dimension and strength of the ultra high pressure common rail fuel injection tube through optimization of Plug angle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.509-518
• /
• 1987

The paper is concerned with the analysis of axisymmetric forward extrusion by using the method of weighted residuals. In the method of weighted residuals, the flow function and the stress functions are assumed so as to cover the global control volume. The derived stress and strain components are used to formulate a constitutive equation in the error form, so that the error is minimized to determine the stress and strain components. The method of least squares is then chosen for the minimization of errors. The distribution of stresses and strains and the forming load are determined for the workhardening material considering the frictional effect at the die surface. The computed results are very similar to those obtained by the finite element method. The method is simpler in application and requires less computational time than the finite element method. Experiments are carried out for aluminum and steel specimens using curved dies. It is found that the experimental observation is mostly in agreement with the computed results by the method of weighted residuals.

• Transactions of Materials Processing
• /
• v.18 no.8
• /
• pp.640-645
• /
• 2009

Recently, boss and rib test based on backward extrusion process was proposed to quantitatively evaluate the interfacial friction condition in bulk forming process. In this test, the tube-shaped punch with hole pressurizes the workpiece so that the boss and rib are formed along the hole and outer surface of the punch. It was experimentally and numerically revealed that the height of boss is higher than that of the rib under the severe friction condition. This work is focused on the effect of the punch design and flow stress on deformation pattern in boss and rib test. From the boss and rib test simulations, it was found that there is slight variation in both the heights of boss and rib according to the length of punch land, nose radius, and face angle. However the hole diameter of the punch and the clearance between the punch and die have a significant influence on the calibration curves showing the heights of the boss and rib. In addition, the effect of flow stress on the calibration curves was investigated through FE simulations. It was found that there is no effect of strength coefficient of the workpiece on the calibration curves for estimation of friction condition. On the other hand, the strain-hardening exponent of the workpiece has a significant influence on the calibration curve.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1752-1758
• /
• 2008

This paper deals with the reduction of friction torque in permanent magnet motors by using the heat treatment of stator core. The stator core is made of electrical steel sheared by the punching die. From the punching process, large mechanical stress acting on the edge of stator tooth induces significant plastic and elastic deformation and then cause the change of magnetization properties. Then, the mechanical and magnetic unbalance in the sheared region of stator tooth produced by material cutting has influence on the friction torque. This paper investigated the effect of the punching process on the magnetization process and the mechanical deformation, and then proposed the stress relief annealing method for the reduction of friction torque among one of motor characteristics.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.16-16
• /
• 1998

우주발사체용 로켓트 구조재로 사용되는 알루미늄합금 단조재는 강도확보를 위하여 고온으로 가열후 급냉과정에서 상당한 크기의 잔류응력이 발생되고 이로 인해 기계가공시 변형이 유발되어 조립성이 나빠진다. 잔류응력은 그 크기가 재료의 항복강도를 초과할 때 제거되므로 응력제거(stress relief)를 위해서는 외부하중이 가해져야 한다. 응력제거 처리는 소성변형, 열처리 및 초음파 등의 방법으로 수행되며 소성변형에 의한 제거효과가 가장 크다 형상이 복잡한 형 단조재의 경우 열간단조금형과 동일한 금형을 이용하는 TX52 등의 방법을 적용한다고 알려져 있으나 TX54에 대한 금형설계 및 소성변형률 적용 데이터는 공정 know-how로 분류되어 있다. 잔류응력제거 처리의 해석적 연구로는 판재와 링롤재에 대해서는 인장 및 압축 소성변형에 적용에 대한 결과가 발표된 바 있으나 형 단조재의 경우에는 전무하다

• Transactions of Materials Processing
• /
• v.21 no.5
• /
• pp.291-297
• /
• 2012

In this paper, the effect of back tension in multi-pass drawing or wiredrawing on the central bursting defect is investigated using finite element predictions. A rigid-plastic finite element method was used together with the McClintock damage model. Central bursting defects under different back tension stress values ranging from 0% to 20% of the yield strength of the material were predicted and they were compared to understand the effect of the back tension stress values on the central bursting defect. It is found that the level of back tension has a strong influence on the cumulative damage. Thus, higher back tension raises the possibility of the central bursting defect occurring, even though it decreases the interfacial pressure between the die and the work piece.

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.490-496
• /
• 2004

Springback comes from the release of external loads after forming. The control of phenomenon is especially important in the sheet metal forming since there are no other practical methods available to correct the dimensional inaccuracy from springback. Therefore the accurate prediction before the die machining has been a long goal in the field of sheet metal forming. The am of the present study is to enhance the prediction capability of finite element (FE) analysis for the springback phenomenon. For this purpose FE analysis for V-bending has been carried out with the commercial programs, LS-DYNA. The FE analysis results have been validated through the comparison of experimental. The experimental results measured directly by the strain gauge have given the confidence to FEA.

• Journal of the Korean Society of Safety
• /
• v.26 no.4
• /
• pp.1-6
• /
• 2011

New methods for joining sheet of metal are being sought. One of the most promising methods is MPJ (mechanical press joining). It has been used in thin metal work because of its simple process and relative advantages over other methods, as it requires no fasteners such as bolts or rivets, consumes less energy than welding, and produces less ecological problems than adhesive methods. In this study, the joining process and static behavior of single overlap joints has been investigated. During fixed die type joining process for SPCC plates, the optimal applied punching force was found. The maximum tensile-shear strength of the specimen produced at the optimal punching force was 1.75 kN. The FEM analysis result on the tensile-shear specimen showed the maximum von-Mises stress of 373 MPa under the applied load of 1.7 kN, which is very close to the maximum tensile strength of the SPCC sheet(= 382 MPa). This suggests that the FEM analysis is capable of predicting the maximum tensile load of the joint.