• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.109-113
• /
• 2011

In intelligent subway systems, UWB-based WiMedia D-MAC Protocol can be considered to send and receive multimedia data which requires high data rate. However, network devices which do not exist within 10 meters, the limited communication rage, can not communicate with each other because WiMedia does not support multi-hop communications. In this paper, we developed the algorithm to select a relaying device for multi-hop routing on WiMedia networks. In the first step, each device acquires information of neighbors through beacon and decides whether it is a normal or relaying device using the acquired information. In the next step, all devices can create the 2-hop routing table using the information received via relaying devices and the whole routing table for all devices on networks, eventually.

• Smart Structures and Systems
• /
• v.26 no.5
• /
• pp.605-617
• /
• 2020

In this study, the experimental tests for the direct tensile strength measurement of Ultra-High Performance Concrete (UHPC) were numerically modeled by using the discrete element method (circle type element) and Finite Element Method (FEM). The experimental tests used for the laboratory tensile strength measurement is the Compressive-to-Tensile Load Conversion (CTLC) device. In this paper, the failure process including the cracks initiation, propagation and coalescence studied and then the direct tensile strength of the UHPC specimens measured by the novel apparatus i.e., CTLC device. For this purpose, the UHPC member (each containing a central hole) prepared, and situated in the CTLC device which in turn placed in the universal testing machine. The direct tensile strength of the member is measured due to the direct tensile stress which is applied to this specimen by the CTLC device. This novel device transferring the applied compressive load to that of the tensile during the testing process. The UHPC beam specimen of size 150 × 60 × 190 mm and internal hole of 75 × 60 mm was used in this study. The rate of the applied compressive load to CTLC device through the universal testing machine was 0.02 MPa/s. The direct tensile strength of UHPC was found using a new formula based on the present analyses. The numerical simulation given in this study gives the tensile strength and failure behavior of the UHPC very close to those obtained experimentally by the CTLC device implemented in the universal testing machine. The percent variation between experimental results and numerical results was found as nearly 2%. PFC2D simulations of the direct tensile strength measuring specimen and ABAQUS simulation of the tested CTLC specimens both demonstrate the validity and capability of the proposed testing procedure for the direct tensile strength measurement of UHPC specimens.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1093-1097
• /
• 2020

This work describes the design and characterization of a Ku-band monolithic microwave integrated circuit (MMIC) power amplifier (PA) for satellite communication applications. The device technology used relies on 0.25 ㎛ gate length gallium arsenide (GaAs) pseudomorphic high electron mobility transistor (PHEMT) of wireless information networking (WIN) semiconductor foundry. The developed Ku-band PHEMT MMIC power amplifier has a small-signal gain of 22.2~23.1 dB and saturated output power of 34.8~35.4 dBm over the entire band of 13.75 to 14.5 GHz. Maximum saturated output power is a 35.4 dBm (3.47 W) at 13.75 GHz. Its power added efficiency (PAE) is 30.6~37.83% and the chip dimensions are 4.4 mm×1.9 mm. The developed 3 W PHEMT MMIC power amplifier is expected to be applied in a variety of Ku-band satellite communication applications.

• Journal of Wellbeing Management and Applied Psychology
• /
• v.7 no.3
• /
• pp.67-72
• /
• 2024

This study developed a dry composite module-type deodorization facility with Twisting airflow changes and two forms (catalyst, adsorbent) within one module. Experiments were conducted to evaluate the reduction efficiency of odor substances C₈H₇N and C₉H₉N. The device combines UV oxidation using TiO₂, catalytic oxidation using MnO₂, and adsorption using A/C in five different methods. Data analysis of experimental results utilized the statistical package program Python 3.12. The program applied frequency analysis of odor removal efficiency, one-way ANOVA, and post-hoc tests, with statistical significance determined by p-value to ensure reliability and validity of the measurements. Results indicated that the highest removal efficiency of C₈H₇N and C₉H₉N was achieved by the UV+A/C method, suggesting the superior effectiveness and efficiency of the developed device. Combining multiple processes and technologies within one module enhanced odor treatment efficiency compared to using a single method. The device's modularity allows for flexibility in adapting to various sewage treatment scenarios, offering easy maintenance and cost-effective deodorization. This composite reaction module device can apply multiple technologies, such as biofilters, plasma, activated carbon filters, UV-photocatalysis, and electromagnetic-chemical systems. However, this study focused on UV-photocatalysis, catalysts, and activated carbon filters. Ultimately, the research demonstrates the practical applicability of this innovative device in real sewage treatment operations, showing excellent reduction efficiency and effectiveness by integrating UV oxidation, TiO₂ photocatalysis, MnO₂ catalytic oxidation, and A/C adsorption within a modular system.

• The Journal of Korean Society for Radiation Therapy
• /
• v.35
• /
• pp.33-39
• /
• 2023

Purpose: The purpose of this study is to find out the dose variation according to thickness of the air gap between the patient's body surface and immobilization device in the treatment plan. Materials and Methods : Four conditions were created by adjusting the air gap thickness using 5 mm bolus, ranging from 0 mm to 3 mm bolus. Immobilization was placed on top in each case. And computed tomography was used to acquire images. The treatment plan that 430 cGy (Relative Biological Effectiveness,RBE) is irradiated 6 times and the dose of 2580 cGy (RBE) is delivered to 95% of Clinical Target Volume (CTV). The dose on CTV was evaluated by Full Width Half Maximum (FWHM) of the lateral dose profile and skin dose was evaluated by Dose Volume Histogram (DVH). Result: Results showed that the FWHM values of the lateral dose profile of CTV were 4.89, 4.86, 5.10, and 5.10 cm. The differences in average values at the on the four conditions were 3.25±1.7 cGy (RBE) among D_95% and 1193.5±10.2 cGy (RBE) among D_95% respectively. The average skin volume at 1% of the prescription dose was 83.22±4.8%, with no significant differences in both CTV and skin. Conclusion: When creating a solid-type immobilization device for carbon particle therapy, a slight air gap is recommended to ensure that it does not extend beyond the dose application range of the CTV.

• The Research Journal of the Costume Culture
• /
• v.17 no.2
• /
• pp.320-329
• /
• 2009

This research attempts to develop a method to relieve dysmenorrhea, which is an obstacle to many women's social activities, by designing a smartwear with built-in thermotherapy and TENS device. TENS therapy has the advantages of being controlled by patients and not depending on the use of drugs. The TENS device is designed as a stomach band so as to be unnoticeable to others when outer clothes are worn; the size was minimized and attached to underwear to facilitate use everywhere at any time. A current problem is the limitation of minimizing, but as battery technology is further developed, we can anticipate much smaller devices. The development of aforementioned smartwear function will increase women's choices in occupations and general improvement in quality of life.

• Journal of Biosystems Engineering
• /
• v.29 no.6 s.107
• /
• pp.515-520
• /
• 2004

A device far estimating the optimal artificial insemination time consisted of a computer, RS module, and six direct-reflex photo-sensors. Program was written in LabWindows CVI. In order to establish references for estimating optimal artificial insemination time, lying rate of the thirty three $Berkshire{\times}Hampshire crossbred sows (parity 5 to 6) was recorded from 2 days after moving into stalls to artificial insemination using a time lapse VCR and was measured every hour with one minute interval using the scan point sampling method. Twenty low hours in a day were divided into three comparing periods : 21:00 to 06:59, 07:00 to 13:59, and 14:00 to 20:59. If sum of the percentages of tying during a comparing period was less than the reference value, the starting hour of the comparing period was considered as onset of estrus and the optimal artificial insemination time was estimated at 20 to 24 hours after onset of estrus. The experimental device was evaluated with twenty five $Berkshire{\times}Hampshire$ crossbred sows (parity 2 to 7) and 23 of 25 sows $(92\%)$ were pregnant. This result suggests that the experimental device is excellent in performance for estimating optimal artificial insemination time.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.4
• /
• pp.35-42
• /
• 2013

In this paper, the analog performance of FinFET structure was estimated by extracting the DC/AC characteristics of the 22 nm process FinFET structures with different layout considering spacer and SEG using 3D device simulator, Sentaurus. Based on the analysis results, layout methods to enhance the analog performance of multi-fin FinFET structures are proposed. By adding the spacer and SEG structures, the drive current of 1-fin FinFET increases. However, the unity gain frequency, $f_T$, reduces by 19.4 % due to the increase in the total capacitance caused by the added spacer. If the process element is not included in multi-fin FinFET, replacing 1-finger with 2-finger structure brings approximately 10 % of analog performance improvement. Considering the process factors, we propose methods to maximize the analog performance by optimizing the interconnect and gate structures.

• The Journal of Korean Society for Radiation Therapy
• /
• v.30 no.1_2
• /
• pp.139-151
• /
• 2018

Objectives : A self-made "Tomotherapy couch device" capable of correcting the Yaw direction was fabricated and evaluated for its usefulness. Materials and Methods : "Tomotherapy couch device" capable of correcting the Yaw direction is made of rigid fibreboard with a flexural strength of $200kg/cm^2$. CBCT Image from Novalis Tx and Iso-Align Phantom from MED-TEC were used to evaluate the physical accuracy. The treatment plan was designed using Accuray $Precision^{TM}$ and In House Head and Phantom. Accuray $PrecisionART^{TM}$ and $Precision^{TM}$ was used to evaluate dose. Results : Evaluation results, the self-fabricated device accurately corrected the setup error, Target dose was within 95 %~107 % of all. In order to directly evaluate the OAR dose according to the Yaw change, the absolute dose was measured. As a result, when the error in the Yaw direction was $3^{\circ}$, the specific OAR showed a maximum difference of 18.4 %. Conclusion : "Tomotherapy couch device" capable of correcting the Yaw direction can be manufactured at a lower cost compared to the effect, and it can prevent the patient's MVCT image dose for re-imaging. Accurate radiation therapy without errors can be performed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.687-695
• /
• 2007

Statement of problem: The proper contact relation between adjacent teeth in each arch plays an important role in the stability and maintenance of the integrity of the dental arches. Proximal contact has been defined as the area of a tooth that is in close association, connection, or touch with an adjacent tooth in the same arch. Purpose: The aim of this study was to develop a digital device for measuring the proximal tooth contact tightness by pulling a thin stainless steel strip (2mm wide, 0.03mm thick) inserted between proximal tooth contact. Material and method: This device consists of measuring part, sensor part, motor part and body part. The stainless steel strip was connected to a stain gauge. The strain gauge was designed to convert the frictional force into a compressive force. This compressive force was detected as a electrical signal and the electrical signal was digitalized by a A/D converter. The digital signals were displayed by a micro-processor. The pulling speed was 8mm/s. Results: For testing reliability of the device in vivo, two healthy young adults (A, B) participated in this experiment. The tightness of proximal tooth contact between the second premolar and the first molar of mandible (subject A) and maxilla (subject B) was measured fifteen times for three days at rest. We double-checked the accuracy of the device with a Universal Testing Machine. Output signals from the Universal Testing Machine and the measuring device were compared. Regression analysis showed high linearity between these two signals. In vivo test, no significant differences were found between measurements. Conclusion: This device has shown to he capable of producing reliable and reproducible results in measuring proximal tooth contact. Therefore, it was considered that this device was appropriate to apply clinically.