• The Journal of the Korea Contents Association
• /
• v.7 no.1
• /
• pp.139-146
• /
• 2007

Most of embedded systems have been developed practically based on the PC platform equipped with Intel x86 CPU since it is able to reduce the total time for product development and improve the reliability of product by making use of a variety of solutions developed for a long time in the PC environment. Also, embedded systems based on PC-platform mainly use a high-capacity hard disk as data storage device for applications intending to store multimedia data. Recently, while the capacity of hard disk is increasing rapidly, the start-up ready time of hard disk is growing longer more than 30 seconds. The lengthened start-up ready time may delay the booting time of embedded system seriously, weighting users down with inconvenience. This paper proposes the refined system architecture and the dynamic IDE device probing method for fast booting of linux kernel in the embedded system based on PC platform with high-capacity hard disks, and the performance of proposed methods is evaluated and presented.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.8
• /
• pp.115-122
• /
• 2017

In this paper, we propose a novel power factor compensation system using slidac. The proposed power factor compensation system compensates the power factor by adjusting the output voltage of the slidac. In the conventional power factor compensation system using capacitor bank method, the power factor compensation error occurs depending on the load condition due to the limitation of the compensation capacitor capacity. However, the proposed system can finely change slidac output voltage applied to the capacitor, therefore power factor can be compensated up to 100% without error. We compare the proposed system with the conventional system, and confirm that the proposed system has excellent power factor compensation performance through simulations and experiments. If the proposed power factor compensation system is applied to an industrial field, a power factor compensation performance can be maximized. As a result, it is possible to reduce of electricity prices, reduce of line loss, increase of load capacity, ensure the transmission margin capacity, and reduce the amount of power generation.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.1
• /
• pp.39-44
• /
• 2010

1.5 V and 3.0 V-class film-type primary batteries were designed for radio frequency identification (RFID) tag. Efficient fabrication processes such as screen-printings of conducting layer ($25{\mu}m$), active material layer ($40{\mu}m$ for anode and $80{\mu}m$ for cathode), and electrolyte/separator/electrolyte layer ($100{\mu}m$), were adopted to give better performances of the 1.5 V-class film-type Leclanch$\acute{e}$ primary battery for battery-assisted passive (BAP) RFID tag. Lithium (Li) metal is used as an anode material in a 3.0 V-class film-type $MnO_2||$Li primary battery to increase the operating voltage and discharge capacity for application to active sensor tags of a radio frequency identification system. The fabricated 3.0 V-class film-type Li primary battery passes several safety tests and achieves a discharge capacity of more than 9 mAh $cm^{-2}$.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.08a
• /
• pp.2-3
• /
• 2001

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.1
• /
• pp.6-10
• /
• 2010

A measurement of very high torque for track drive unit in construction equipment is usually in difficulties due to the requirement of a torque meter with high capacity, and the limitation of geometry for an experimental set-up. To improve the troublesome problem, a new device was proposed, where a torque transmitted through the torque arm can be measured by load cells attached at each torque arm. The experimental set-up of the new device was carried out in order to measure the torque values for a mechanical feedback type planetary gear box, in which the power flow circulates itself in a closed-loop. The new device enables to measure torque values of 60,000Nm. Additionally, the measured values were estimated statistically in the aspect of their repeatability and reproducibility, so that an acceptable behaviour as a measuring device can be confirmed.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.279-281
• /
• 1996

This paper deals with the two stage surge protection device by using varistor and LC low pass filter. Recently varistor alone has been used with overvoltage protection devices for the AC power mains and has same problems associated with high remnant voltage and noise. In this work, in order to improve the cutoff performance of surge protection device, the lightning surge protection device having two stage hybrid circuit for an AC single phase mains was designed and fabricated. Operation characteristics and surge clamping performance of the surge protection device in an $8/20{\mu}s$ surge current are investigated. As a consequence, it is found that the proposed two stage surge protective device for AC power mains has a variety of advantages such as a smaller clamping voltage, high frequency noise reduction and large clamping capacity.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.1
• /
• pp.53-58
• /
• 2013

In this paper, we proposed low power algorithm for battery residual capacity and a task. Algorithm the mobile devices power of the battery residual capacity for the task to perform power consumption to reduce the frequency alters. Task is different in power consumption according to kinds of in time accomplishment device to use. Adjustment of power consumption analyzes kinds of given tasks from having the minimum power consumption task to having the maximum power consumption task. Control frequency so that power consumption waste to be exposed to battery residual capacity can be happened according to the results analyzed. Experiment the frequency by adjusting power consumption a method to reduce using [7] and in the same environment power of the battery residual capacity consider the task to perform frequency were controlled. Efficiency was proved compare with the experiment results [7]. The experiments results show increment in the number of processing by 45.46% comparing with that [7] algorithm.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.2
• /
• pp.483-503
• /
• 2015

This paper analyzes the optimal user density and power allocation for Device-to-Device (D2D) communication underlaying cellular networks on multiple bands with the target of maximizing the D2D transmission capacity. The entire network is modeled by Poisson point process (PPP) which based on stochastic geometry. Then in order to ensure the outage probabilities of both cellular and D2D communication, a sum capacity optimization problem for D2D system on multiple bands is proposed. Using convex optimization, the optimal D2D density is obtained in closed-form when the D2D transmission power is determined. Next the optimal D2D transmission power is obtained in closed-form when the D2D density is fixed. Based on the former two conclusions, an iterative algorithm for the optimal D2D density and power allocation on multiple bands is proposed. Finally, the simulation results not only demonstrate the D2D performance, density and power on each band are constrained by cellular communication as well as the interference of the entire system, but also verifies the superiority of the proposed algorithm over sorting-based and removal algorithms.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.4
• /
• pp.1481-1500
• /
• 2016

Device-to-Device (D2D) communication underlaying macro-small cell networks, as one of the promising technologies in the era of 5G, is able to improve spectral efficiency and increase system capacity. In this paper, we model the cross- and co-tier D2D communications in two-tier macro-small cell networks. To avoid the complicated interference for cross-tier D2D, we propose a mode selection scheme with a dedicated resource sharing strategy. For co-tier D2D, we formulate a joint optimization problem of power control and resource reuse with the aim of maximizing the overall outage capacity. To solve this non-convex optimization problem, we devise a heuristic algorithm to obtain a suboptimal solution and reduce the computational complexity. System-level simulations demonstrate the effectiveness of the proposed method, which can provide enhanced system performance and guarantee the quality-of-service (QoS) of all devices in two-tier macro-small cell networks. In addition, our study reveals the high potential of introducing cross- and co-tier D2D in small cell networks: i) cross-tier D2D obtains better performance at low and medium small cell densities than co-tier D2D, and ii) co-tier D2D achieves a steady performance improvement with the increase of small cell density.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.11
• /
• pp.97-106
• /
• 2022

The domestic auger-drilled pile method generally manages the driving penetration (set) value with the final stage of construction. The penetration value has been estimated by manual measurement for a long time. The automation technology is yet to be applied due to workability and high-cost limitations, despite safety issues and lack of reliability in measured results. In this study, a non-contact pile penetration measurement device was developed. Further, the field performance was verified by comparing the measurements with a conventional automation device. In addition, the on-site field quality control method was analyzed using the penetration measuring device. The field experiments confirmed that more reliable bearing capacity estimation could calculate the dynamic damping coefficient and the modified Hiley formula with the developed device. Furthermore, it can be used for pile construction management from the bearing capacity viewpoint, even for piles not subjected to dynamic load tests.