• Animal Bioscience
• /
• v.36 no.5
• /
• pp.776-784
• /
• 2023

Objective: This experiment was conducted to evaluate the inclusion of dietary nontoxic sulfur (NTS) on growth performance, immune response, sulfur amino acid composition and meat characteristics in growing-finishing pigs. Methods: A total of 140 crossbred pigs ([Yorkshire×Landrace]×Duroc) with an average body weight of 34.73±0.66 kg were used for the 12-week feeding trial. Experimental pigs were allotted to one of 5 treatments in 4 replicates of 7 pigs per pen in a randomized complete block (RCB) design. The experimental treatments were as follows (0%, 0.1%, 0.2%, and 0.4% NTS levels): i) Control, corn soybean meal (SBM)-based diet; ii) NTS 0.1, basal diet + NTS 0.1%; iii) NTS 0.2, basal diet + NTS 0.2%; iv) NTS 0.4, basal diet + NTS 0.4%. Results: Body weight increased linearly as dietary NTS levels increased up to 0.2% (linear; p = 0.04) in the early finishing phase (9 weeks). During the whole experimental period, body weight and average daily gain linearly increased as the dietary NTS level increased in the diet (linear; both p = 0.01), but quadratic responses in body weight and average daily gain were observed with the addition of NTS 0.4% (quadratic, both p = 0.01). In the late finishing period, the IgG concentration increased linearly (linear; p = 0.01) as the dietary NTS level increased up to 4%. In the finishing period, a linear response was observed as a dietary NTS level was added (linear; p = 0.03), and supplementation with 0.2% NTS resulted in a higher methionine content than the other treatments (quadratic; p = 0.01). NST 0.2% had a lower value of thiobarbituric acid reactive substances (quadratic; p = 0.01). Conclusion: Consequently, supplementation with dietary NTS up to 0.2% could improve growth performance, amino acid composition in hair and meat antioxidation capacity.

• Nuclear Engineering and Technology
• /
• v.43 no.2
• /
• pp.149-158
• /
• 2011

Metal waste generated from the pyroprocessing of 10 MtU of spent fuel was classified by comparing the specific activity of a relevant radionuclide with the limit value of the specific activity specified in the Korean acceptance criteria for a lowand intermediate-level waste repository. A Korean Optimized Fuel Assembly design with a 17${\times}$17 array, an initial enrichment of 4.5 weight-percent, discharge burn-up of 55 GWD/MtU, and a 10-year cooling time was considered. Initially, the mass and volume of each structural component of the assembly were calculated in detail, and a source term analysis was subsequently performed using ORIGEN-S for these components. An activation cross-section library generated by the KENO-VI/ORIGEN-S module was utilized for top-end and bottom-end pieces. As a result, an Inconel grid plate, a SUS plenum spring, a SUS guide tube subpart, SUS top-end and bottom-end pieces, and an Inconel top-end leaf spring were determined to be unacceptable for the Gyeongju low- and intermediate-level waste repository, as these waste products exceeded the acceptance criteria. In contrast, a Zircaloy grid plate and guide tube can be placed in the Gyeongju repository. Non-contaminated Zircaloy cladding occupying 76% of the metal waste was found to have a lower level of specific activity than the limit value. However, Zircaloy cladding contaminated by fission products and actinides during the decladding process of pyroprocessing was revealed to have 52 and 2 times higher specific activity levels than the limit values for alpha and $^{90}Sr$, respectively. Finally, it was found that 88.7% of the metal waste from the 17${\times}$17 Korean Optimized Fuel Assembly design should be disposed of in a deep geological repository. Therefore, it can be summarized that separation technology with a higher decontamination factor for transuranics and strontium should be developed for the efficient management of metal waste resulting from pyroprocessing.

• Research in Community and Public Health Nursing
• /
• v.32 no.4
• /
• pp.485-496
• /
• 2021

Purpose: This study attempted to obtain basic data for developing a global nursing practice education program. Methods: The data collection period was from July 2 to 11, 2020. The study participants were professors with experience in design, operation and management of global nursing practice education or experts with experience in international cooperation projects, and 8 people who agreed to participate in focus group interview (FGI). FGI was conducted twice in total and the directed content analysis method was applied. Results: The categories of 'practice design' are 'growing as a global nursing leader' and 'working together towards one goal'. The categories of 'practice operation' are 'watching, listening, and performing', 'self-directed organizing from preparation to finishing', and 'learning the value of participation rather than grades'. The category of 'practice management' is 'one's own weight to carry'. Conclusion: Global nursing practice education aims one goal - growing as a global nursing leader - and is self-directed course from preparation to an end with watching, listening and performing together. It is about learning the value of participation rather than grades. This can be used as basic data for the design, operation and management of global nursing practice education in the future.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.710-713
• /
• 2005

Many impact or drop test researches of home appliances are published, but those of toys cannot be found easily. External impacts are the primary causes of fracture of toys. For impact proof design, the finished product should pass an impact test after molding design. There are several international toy safety standards or requirements such as US CPSC(Consumer Product Safety Commission), ASTM F963-96a, EN71 and so on. The puppy robot which patrols around the house, namely, the watchdog was selected to investigate toy safety because it has considerable weight and outer panels are made of plastics. First the model of watchdog robot was obtained by 3 dimensional scan. Surface data can be generated from 3D polygon data of the watchdog. A reliable drop simulation method for the watchdog was established using Pam-crash program according to Korean toy safety standards. When there is a low impact allowance value, the molding design should be reinforced or changed. It was found that the maximum impact stress reaches the ultimate stress of panel material.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.3 s.234
• /
• pp.503-510
• /
• 2005

In this paper, the topology optimization of inner-wall stiffener of cylindrical containers for the use as a rocket fuel tank is presented. Such structures for space mission should have high stiffness against the buck]ins while their weight should be maintained low from the viewpoint of cost and performance. Therefore, in the present work the reciprocal of critical buckling load is adopted as an objective function and the total mass of stiffener is constrained to a prescribed value. Due to the restriction of computational resources a section of cylindrical container is topologically optimized and this result is repeated to obtain the full design. Also, for manufacturability the concept of periodic topology pattern in design domain is newly introduced. In the numerical examples, the results by the proposed approach are investigated and compared with those of isogrid design.

• IE interfaces
• /
• v.9 no.1
• /
• pp.13-24
• /
• 1996

Quality of injection molded parts is dependent on both mold design and processing conditions. From the mold design point of view, an optimal shrinkage should be used to compensate the shrinkage of molded parts. From the processing point of view, it is important to analyze the priority of processing conditions because a number processing conditions affect the quality of molded parts. Processing analysis employing the design of experiment was performed, and the shrinkage of molded part was considered as a characteristic parameter to improve the quality. As the result of the analysis of variance on SN ratio of a characteristic value, injection speed and bolding pressure were selected as two effective process parameters. Regression analysis on shrinkage and processing conditions was carried out, and an optimal processing condition was obtained by the response surface analysis. Shrinkage at the optimal condition could be used to reduce the number of try-cut at the step of mold making. The ranges of indirect control parameter, such as maximum cavity pressure or weight, measured at the optimal processing condition were used for monitoring the quality of molded parts in process.

• Animal Bioscience
• /
• v.36 no.1
• /
• pp.108-118
• /
• 2023

Objective: The objective of this experiment was to determine the net energy (NE) value of 6 wheat bran and 1 wheat shorts by indirect calorimetry and establish the NE prediction equations of wheat bran fed to growing barrows. Methods: Forty-eight growing barrows (28.5±2.4 kg body weight) were allotted in a completely randomized design to 8 dietary treatments that included a corn-soybean meal basal diet, 6 wheat bran diets and 1 wheat shorts diet. The inclusion level of wheat bran or wheat shorts in diets is 30%. Results: The addition of wheat bran reduced the apparent total tract digestibility (ATTD) of nutrients (p<0.05). The ATTD of gross energy, crude protein (CP) and dry matter (DM) in the wheat shorts were greater than that in the wheat bran. Addition of wheat bran or wheat shorts had no effect on total heat production and fasting heat production. The NE of wheat bran was negatively correlated with neutral detergent fiber (r = -0.84; p<0.05) and acid detergent fiber (r = -0.83; p<0.05), while it was positively correlated with CP (r = 0.92; p<0.01). The NE values of wheat bran ranged from 6.79 to 8.15 MJ/kg DM, and the NE value of wheat shorts was 12.47 MJ/kg DM. The ratio of NE to metabolizable energy for wheat bran fed to growing pigs was from 66.0% to 71.7%, whereas the value for wheat shorts was 83.7%. Conclusion: The NE values of wheat bran ranged from 6.79 to 8.15 MJ/kg DM, and the NE value of wheat shorts was 12.47 MJ/kg DM. The NE value of wheat bran can be well predicted based on energy content and proximate analysis.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.127-133
• /
• 2018

To reduce fuel consumption, research on the weight reduction of vehicles is being actively carried out. Researchers have typically tried to replace metal materials with composites materials, but these materials did not satisfy the required strength and rigidity of a vehicle. Composites are usually not used because of their high cost. There are incomplete studies on lightweight trucks that transport cargo. Therefore, in this paper, we enhance the lightness and mechanical strength through design optimization of the deck frame for a lightweight truck. For that purpose, the side member and cross member, which are mounted on the lower part of the truck to assure the safety of the vehicle and support the luggage load, were targeted. The result of numerical analysis on the safety of the frame was obtained by changing the shape of each cross-section. To verify the numerical analysis, we compared it with the theoretical value of a cantilever beam. As a result, the suitability of the cross-sectional shapes of each frame was confirmed through numerical analysis.

• Hwankyungkyoyuk
• /
• v.14 no.1
• /
• pp.32-42
• /
• 2001

This study examined the effects of prompts, environmental alteration, and feedback on reduction of food wastes. The study was conducted at a student restaurant at a university. Subjects in this study were college students, faculty members and administrative staffs at the university. An A-BC-BCD-BC within subject design was employed. After baseline phase(A), prompts and environmental alteration were manipulated in the second phase(BC). In the next phase(BCD), feedback was added in addition to the prompts and environmental alteration. In the last phase(B), all the treatments except environmental alteration were withdrawn. The dependent variables n cluded (1) total weight of food waste per day, (2), the weight of food waster per person, (3) the ratio of food waste to total food served per day, (4) total amount of monetary value for food waste to total food served per day. The results indicated that prompts and environmental alteration were affective in reducing food wastes. Thus, measures of all the dependent variables decreased when environmental alteration and prompts were manupulated. However, when feedbacks were added to prompts and environmental alteration, the additional effect of feedback was not observed. The implications and limitations of these findings were discussed and the directions of future studies were also proposed.

• Textile Coloration and Finishing
• /
• v.25 no.4
• /
• pp.303-313
• /
• 2013

Alkali hydrolysis of sea-island PET 0.02denier microfiber were compared to those on the fabrics of the 0.06denier microfiber. In the dissolution of the sea component out of sea island type ultra-microfiber, it is important to determine the optimum division and divided material. Weight reduction of sea island ultra-micro sea island fiber was faster than regular PET about 10 times. Also 0.2denier sea-island ultra-micro sea island fiber has better color fastness (washing, friction, and daylight) than 0.06denier level sea-island ultra-microfiber. In this study, 0.2denier ultra-micro sea island fiber shows the possibility of high value product.