• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.50-55
• /
• 2011

The fluid power products are widely used in current industrial area such as automation of products and equipment assembly, high-tech machine tool, aircraft, train, and etc. As the development of industry is in progress, the development of the fluid power products is demanding and it is required in every industrial area. This research proposed a pneumatic system to evaluate displacement accuracy of the pneumatic actuator without external load and to analyze capability of integration of the valve system. The pneumatic system consisted of a combination of pneumatic actuator, four two-port valves, two three-port valves, two pressure valve, a check valve, two proximity sensors, and a program logic controller (PLC). The position controller is based on the PLC connected with the proximity sensors. The maximum air pressure applied for tests was $49.05N/cm^2$ and the displacement accuracy of a stroke was measured using a dial gauge. The supply- and discharge-side of air pressure and the length of the stroke of the pneumatic cylinder were varied The test of the position control of the pneumatic cylinder was carried out 50 times at each supply- and discharge-side air pressure of 24.53/34.34, 29.43/39.24, 34.34/44.15, and $39.24/49.05N/cm^2$ and replicated three times. The accuracy of the displacement of the pneumatic cylinder stroke increased as the supply- and discharge-side of air pressure increased with the stroke length of 133mm. Also the displacement accuracy increased as the stroke length increased with the fixed supply- and discharge-side of air pressure of the pneumatic cylinder as 34.34 and $44.15N/cm^2$, respectively. The most accurate displacement of the pneumatic cylinder was obtained at the supplyand discharge-side of air pressure of 39.24 and $49.05N/cm^2$, respectively, and strokes of 170 and 190mm.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.613-620
• /
• 2021

A flow channel shape of PEMFC has an influence on the internal flow uniformity. If the reactant distribution in a flow path is not uniform during operation, both catalyst deactivation and mechanical damage of membrane could occur resulting in decreasing the membrane electrode assembly (MEA) durability. Numerous studies concerning flow design have been conducted to make smooth supply and uniform distribution of reactants in fuel cells. The baffle of flow path could improve fuel cell performance through the forced convection effect. A sub-channel, as an additional air flow path, could increase the reactant concentration and reduce the mass transfer loss via a smooth water discharge. In this study, computational fluid dynamics (CFD) was used to analyze the effect of blocks and sub-channels on the current density and oxygen concentration of the fuel cell. As a result, the limit current density and oxygen concentration at a rear block increased when using blocks and sub-channels in a flow channel. In particular, the current density increased significantly when the sub-channel was placed between two blocks. Also, the sub-channel position was optimized by analyzing the oxygen concentration, and the oxygen concentration was recovered at a rear block in the fuel cell.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.2
• /
• pp.92-107
• /
• 2018

In 2013~2016, gilt-bronze shoes were excavated from the ancient tombs in Jeongchon Village located at Bogam-ri, Dasi-myeon in Naju. They are estimated to have been made in the late 5th or early 6th centuries. The gilt-bronze shoes are significant in that they serve to explicate the relationship between the center of Baekje and the local forces in the Yeongsan River Basin. This study's specific focus was the gilt-bronze shoes from the ancient tombs in Jeongchon Village. Based on the findings, a restoration drawing was designed and restored products were manufactured by considering metalwork techniques used to manufacture the original ones. At first, manufacturing techniques were tested by using a scientific analysis and visual observation. The manufacturing method, structures, and patterns of the gilt-bronze shoes were closely examined. Then, a design drawing of gilt-bronze shoes was created through field measurement and they were recreated on the basis of the analysis. The original form of the restored products were manufactured through cutting out the outward form, bore carving, engraving, molding, plating, and an assembly process. In the restoration process, this study examined the formal characteristics of gilt-bronze shoes, manufacturing techniques, and archetypes during Baekje's late Hanseong era. Products restored from this study are expected to be used as achievements for more easily understanding the culture of Baekje.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.1
• /
• pp.15-22
• /
• 2022

This paper introduces research on the hinge joint of modular structure joints using finite element analysis. The modular structure has a characteristic in that it is difficult to expect the integrity of columns and beams between unit modules because the construction is carried out such that the modules are stacked. However, the current modular design ignores these structural characteristics, considers the moment transmission for the lateral force, and analyzes it in the same manner as the existing steel structure. Moreover, to fasten the moment bonding, bolts are fastened outside and inside the module, resulting in an unreasonable situation in which the finish is added after assembly. To consider the characteristics that are difficult to expect, such as unity, a modular structure system using hinge joints was proposed. This paper proposed and reviewed the basic theory of joints by devising a modified scissors model that is modified from the scissors model used in other research to verify the transmission of load when changing from the existing moment junction to a hinge junction. Based on the basics, the results were verified by comparing them with Midas Gen, a structural analysis program. Additionally, the member strength and usability were reviewed by changing the modular structure designed as a moment joint to a hinge joint.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.3
• /
• pp.339-346
• /
• 2019

Based on the $8^{th}$ Basic Plan for Electric Power Demand and Supply, an estimation has been made for inventories and characteristics of spent fuel (SF) to be generated from existing and planned nuclear power plants. The characteristics under consideration in this study are dimensions, fuel array, $^{235}U$ enrichment, discharge burnup, and cooling time for each fuel assembly. These are essentially needed for designing a disposal facility for SFs. It appears that the anticipated quantity by the end of 2082 is about 62,500 assemblies for PWR SFs. The inventories of Westinghouse-type and Korean-type SFs were revealed to be 60% and 40%, respectively as of the end of 2018. The proportion of SFs with initial $^{235}U$ enrichment below 4.5 weight percent (wt%) was shown to be approximately 90% in total as of the end of 2018. As of 2077, more than 97% of SFs generated from Westinghouse-type nuclear reactors were shown to have cooling time of over 50 years. As of 2125, more than 98% of SFs generated from Korean-type nuclear reactors were shown to have cooling time of over 45 years. Based on these results, for the efficient design of a disposal system, it is reasonable to adopt two types of reference spent fuel. SF of KSFA with $^{235}U$ enrichment of 4.5 wt%, discharge burnup of 55 GWd/tU, and cooling time of 50 years was determined as reference fuel for Westinghouse-type SFs; SF of PLUS7 with $^{235}U$ enrichment of 4.5 wt%, discharge burnup of 55 GWd/tU, and cooling time of 45 years was determined as reference fuel for Korean-type SFs.

• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.667-685
• /
• 2022

This paper aims to investigate 4D printing materials for soft robots. 4D printing is a targeted evolution of the 3D printed structure in shape, property, and functionality. It is capable of self-assembly, multi-functionality, and self-repair. In addition, it is time-dependent, printer-independent, and predictable. The shape-shifting behaviors considered in 4D printing include folding, bending, twisting, linear or nonlinear expansion/contraction, surface curling, and generating surface topographical features. The shapes can shift from 1D to 1D, 1D to 2D, 2D to 2D, 1D to 3D, 2D to 3D, and 3D to 3D. In the 4D printing auxetic structure, the kinetiX is a cellular-based material design composed of rigid plates and elastic hinges. In pneumatic auxetics based on the kirigami structure, an inverse optimization method for designing and fabricating morphs three-dimensional shapes out of patterns laid out flat. When 4D printing material is molded into a deformable 3D structure, it can be applied to the exoskeleton material of soft robots such as upper and lower limbs, fingers, hands, toes, and feet. Research on 4D printing materials for soft robots is essential in developing smart clothing for healthcare in the textile and fashion industry.

• The Journal of Korean Academy of Prosthodontics
• /
• v.51 no.4
• /
• pp.315-322
• /
• 2013

Purpose: To evaluate the axial displacement of implant-abutment assembly after cyclic loading in internal tapered connection system. Materials and methods: External butt-joint connection implant and internal tapered connection implant were connected with three types of abutment for cement-retained prostheses, i.e. external type abutment (Ext group), internal tapered 1-piece abutment (Int-1 group), and internal tapered 2-piece abutment (Int-2 group). For each group, 7 implants and abutments were used. The implantabutments assemblies were clamped into the implant holder for vertical loads. A dynamic cyclic loading was applied for $150{\pm}10N$ at a frequency of 4 Hz. The amount of axial displacement of the abutment into the implant was calculated at each cycle of 0, 5, 10, 50, 100, 1,000, 5,000, and 10,000. A repeated measures analysis of variance (ANOVA) for the overall effect of cyclic loading and the pattern analysis by linear mixed model were used for statistical analysis. Differences at P<.05 were considered statistically significant. Results: The mean axial displacement after 10,000 cycles were $0.714{\pm}0.488{\mu}m$ in Ext group, $5.286{\pm}1.604{\mu}m$ in Int-1 group, and $11.429{\pm}1.902{\mu}m$ in Int-2 group. In the pattern analysis, Int-1 and Int-2 group showed continuous axial displacement at 10,000 cycles. There was no declining pattern of axial displacement in the Ext group. Conclusion: The pattern of linear mixed model in Ext group showed no axial displacement. There were continuous axial displacements in abutment-implant assemblies in the Int-1 and Int-2 group at 10,000 cycles. More axial displacement was found in Int-2 group than in Int-1 group.

• Journal of the Korea Convergence Society
• /
• v.11 no.12
• /
• pp.329-341
• /
• 2020

As COVID-19 pandemic sweeps across the world, more than 45 million confirmed cases and over 1,000,000 deaths have occurred till now, and this situation is expected to continue for some time. In particular, more than half of the infections in European countries such as Italy and Spain occurred in nursing homes, and it is reported that over 4,000 people died in nursing homes for older adults in the United States. Therefore, the issues that need to be addressed after the COVID-19 crisis include finding a fundamental solution to group care and shifting to family-centered care. More specifically, it is expected that there will be ever more lively discussion on establishing and expanding hyper-technology based community care, that is, family-centered care integrated with ICT and other Industry 4.0 technologies. This poses a challenge of how to combine social security and social welfare with Industry 4.0 in concrete ways that go beyond the abstract suggestions made in the past. A case in point is the proposal involving smart welfare cities. Given this background, the present paper examined the concept, scope, and content of non-face-to-face care in the context of previous literature on the function and scope of the social security platform, and the concept and expandability of the smart welfare city. Implementing a smart city to realize the kind of social security and welfare that our society seeks to provide has significant bearing on the implementation of community care or aging in place. One limitation of this paper, however, is that it does not address concrete measures for implementing non-face-to-face care from the policy and legal/institutional perspectives, and further studies are needed to explore such measures in the future. It is expected that the findings of this paper will provide the future course and vision not only for the smart welfare city but also for the social security and welfare system in administrative, practical, and legislative aspects, and ultimately contribute to improving the quality of human life.

• Journal of the Korean Geographical Society
• /
• v.28 no.2
• /
• pp.148-162
• /
• 1993

There is much speculation that modern capi-talist society is undergoing fundamental and qualitative chnge towards flexible specialization. The purpose of this study is to examine this hypothesis. This paper focusses on: the idea of flexible specialization; the significance of this transition; industrial district; and the implicati-ons of this new production system for Korean industrial space. Main arguments of this study are as follows: First, as all different groups of researchers apply the idea of flexible specialization according to their own specifications, the current debate on this topic is not much fruitful. Not surpri-singly, the concept of flexible specialization has overlapped with subocontracting. This intergration of subcontracting into flexible specialization systems, however, is inappropriate because the two concepts have different historical contexts. The other cause of this controversy is its inherent weekness, conceptual ambiguity. Thus, today's flexibility becomes tomorrow's rigidity. Secondly, transition towards flexible speciali-zation has only been partially achieved even in advanced capitalist countries. The application of dualistic explanatory framework, such as rigidity versus flexibiity, mass production versus small-lot multi-product production, and de-skilling versus re-skilling, has resulted in great exaggeration of the transformation, from Fordism to post-Fordism. There is no intermediary part between two places. Considering that the workers allocated to the Fordist mass production assembly line are not as large as one might imagine, the shift from mass to flexible production has only limited implications for the transformation of capitalist economy. Thirdly, 'industrial district' contorversy has contributed to highlighting the importance of small firms and areas as production space. The agglomeration of small firms in specific areas is common in Korea, but it is quite different from the industrial district based on flexible specialization. The Korean phenomenon stems from close interactions with its major parent firm rather than interactions between flexible, specialized, autonomous and technology-intensive smll firms. Most Korean subcontractors are still low-skilled, labour-intensive, and heavily dependent on their mojor parent firms. Thus, the assertion that the Seoul Metropolitan Area adopts flexible specialization has no base. Fourthly, the main concern of flexible speciali zation is small firms. However, the corporate organization that needs product diversification and technological specialization is oligopolistic large corporations typified by multinational corporations. It is because of this that most of these organizations are adoptiong Fordist mass production methods. The problem of product diversification will be resolved naturally if economic internationalization progresses further. What is more important for business success is the quality and price competitiveness of firms rather than product diversification. Lastly, in order to dispel further misunderst-anding on this issue, it is imparative that the conceptual ambiguity is resolved most urgently. This study recommends adoption of more speci-fied and direct terminology (such as, factory automation, computer design, out-sourcing, the exploitation of part-time labor, job redesign) rather than that of ideological ones (such as, Taylorism, Fordism, neo-Taylorism, neo-Fordism, post-fordism, flexible specialization, peripheral post-Fordism). As the debates on this topic just started, we still have long way to go until consensus is reached.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.599-610
• /
• 2016

This paper reports the results of a systematic review (SR) and meta-analysis research to compare the effect of Kangaroo care, targeting mothers and premature infants. A randomized clinical trial study was performed until February 2015. The domestic literature contained the non-randomized clinical trial research without restriction according to the level of the study design. A search of the Ovid-Medline, CINAHL, PubMed and KoreaMed, the National Library of KOREA, the National Assembly Library, NDSL, KISS and RISS. Through the KMbase we searched and combined the main term ((kangaroo OR KC OR skin-to-skin) AND (care OR contact)) AND (infant OR preterm OR Low Birth Weight OR LBW), ((kangaroo OR kangaroo OR kangaroo) AND (care OR nursing care OR management OR skin contact)) was made; these were all combined with a keywords search through the selection process. They were excluded in the final 25 studies (n=3051). A methodology checklist for randomized controlled trials (RCTs) designed by SIGN (Scottish Intercollegiate Guidelines Network) was utilized to assess the risk of bias. The overall risk of bias was regarded as low. In 16 studies that were evaluated as a grade of "++", 9 studies were evaluated as a grade of "+". As a result of meta-analysis, kangaroo care regarding the effects of premature mortality, severe infection/sepsis had an insignificant effect. Hyperthermia incidence, growth and development (height and weight), mother-infant attachment, hypothermia incidence, length of hospital days, breast feeding rate, sleeping, anxiety, confidence, and gratification of mothering role were considered significant. In satisfaction of the role performance, depression and stress presented contradictory research results for individual studies showing overall significant difference. This study has some limitations due to the few RCTs comparing kangaroo care in the country. Therefore, further RCTs comparing kangaroo care should be conducted.