• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.475-482
• /
• 2014

This paper presents the experimental results concentrically reinforced concrete tension members and compares cracking behavior of amorphous steel fiber and normal steel fiber reinforced concrete members. Two kind of steel fibers were included as a major experimental parameter together with the six cover thickness to bar diameter ratio ($c/d_b$). The presence of amorphous steel fibers effectively controlled the splitting cracks initation and propagation. In the amorphous steel fiber reinforced specimens, no splitting cracks were observed that becomes higher with cover thickness to bar diameter ratio is 2.0. Crack spacing of the each specimens reinforced with amorphous steel fibers and normal steel fibers becomes larger with the increase in cover thickness, and also measured maximum and average crack spacing are significantly smaller than current design code provision. Based on the measured crack spacings, a relationships for predicting the crack spacing is proposed using the measured average crack spacing in amorphous steel fiber reinforced concrete tension members.

• 대한공업교육학회지
• /
• v.40 no.1
• /
• pp.105-120
• /
• 2015

The purpose of this study was to extract of Sub-elements of technological communication skills and to construct of a system model. In order to achieve the goal of the study, it was carried out in two steps: (1)Extraction sub-elements and definitions of technological communication skills, (2)Development of a system model of technological communication skills. Obtained conclusions by the process of this research were as follows. First, sub-elements of the technological communication skills were extracted and they were images, sketches, flowcharts, drawings, prototyping, symbols tables graphs and presentations. Second, using the 'technological communication tools' based on the "collaborative activities in online and offline', technological communication skills were defined as communication skills to be raised through the process of 'Idea through the Communication', 'Realization through the Communication', 'Wrap up through the Communication'. Third, technological communication skills were described as the system, in which 'Idea through the Communication(images, sketches, flowcharts)', 'Realization through the Communication(design, prototyping)', 'Wrap up through the Communication(symbol table graph, presentation)' were collaboratively activated. Fourth, checking tool for the technological communication skills was developed, based on checking tool for the existing communication skills and system model for technological communication skills. And it was improved by the expert validity test.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.207-214
• /
• 2016

RFID technology is a technology perceiving information with the device called reader and tag which is now used in public transportation such as Hi-pass. In this paper, we design a system which tracks indoor location using this technology. GPS, the most frequently used location-tracking system, has a defect that its accuracy decreases when the device is indoor. In suggested experiment, we simulate signals according to the moving of located objects, then compare with the result of the experiment. Based on the extracted data, we inform data which is for the purpose of tracking system based on analysis of the route and errors. Simulations for the tracking were performed with relocation of real objects. In the real experiment, we arrange the readers around the room and move the tagged object that we like to know the location, then analyze the data from the equipment. This paper suggests the analyzed data for the future indoor tag tracking applications. We expect that the RFID based location positioning data will be used for other indoor positioning research and development.

• The KIPS Transactions:PartD
• /
• v.10D no.5
• /
• pp.793-804
• /
• 2003

In the latest, it's increasing an applied technology to be related with growth of industry circles. It's one of them a software to be used in industry circles. and It's most important part to apply an industrial equipment, so software to take charge of major part is indicative performance of quipment. At this time, it's inspired an evaluation and measurement of software quality to have within industrial equipment, and it's forming the research and development by the inside and outside of the country. For this, it's constructed a valuation metric to be based on ISO/IEC 12119, the International Standard for general the terms desired of quality of software and ISO/IEC 9126-2, the International Standard of the terms valuation of qualify for evaluation and measure, and for this accomplishment, It has been designed and developed industrial software international standard compatible approval system which approve a quality based on quality test result of industrial software using the ISO/IEC 14598-6 that international standard for organization of evaluation module.

• Journal of the Korean Society of Costume
• /
• v.18
• /
• pp.225-245
• /
• 1992

The button is a part of costume. But it has the symbolism of costume in itself and reflects the sociocultural phenomena. The purpose of this study is to clarify symbolism of button of eighteenth and nineteenth century which had been most popular. This study is based on the library research. Through this paper, I reached conclusions as follows. The symbolism of button is found in various ways. First, Aesthetics is found in material, color, design and type etc. of button. Especially Indian silver button of abstract type shows well distinctive aesthetics of Indians. Second, The material and the number of button vary with one's status and show off one's privilege. I England, there was the rule, in which the symbol of the King was a silver button with a figure of lion. The livery button represents his family to the nble and shows the meaning of obedience to the servant. Third, The button on uniform varies with ranks. This is prominent in a uniform of a soldier or a policeman. Fourth Material and craft of button show one's economic position. The button gives a Very good picture of what one's life was then. Precious button with gold, silver, and other jewels is an index to one's property. Fifth, The button of political event is used for election, which shows the face and the name of runner. Besides that, there were buttons designed for the flag or the slogan for political event. Sixth, The button of social event reflects a social phase of life in war or revolution, for example, it satirizes the burning of the Bastille in the French Revolution, or the taxpayer bearing the burden. Seventh, the buttons that symbolize a historic event are made to commemorante an epochal and critical occurrence or an important person's birth, death, visit to some place, etc., Eighth, there were well-known persons, for example, a president, a king, a queen, a singer, or an artist in the buton of personality. Nineth, The button of one's company shows one's community in figures or pictures, that is, this button is used as a symbol one's community. Tenth, The button varies with the development of science and technology. It gives a very good picture of what it was and what the technological level was. Eleventh, The buttons that symmbolize on occupation most impressively are uniform buttons. Symbolic marks related with a particular occupation are carved on the buttons of compary employees' uniforms. Twelfth, Various natural phenomena are designed to appear on buttons, Some express themselves simply as they are, and others appear as a symbolic form such as environmental relationship between men and nature, four seasons, a constellation and all other natural things occurring during a year. Finally, The button of rebus is a motto expressed by a combination with objects figures, letters, words, or phrases.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.3
• /
• pp.25-34
• /
• 2018

This paper presents a heating source of carbon nanofibers for the efficiency and the drying performance of laundry dryer, and focuses on the applicability-evaluation of its source. To design the proposed heating module, experiments were conducted in terms of surface temperature and surface temperature distribution characteristics of carbon nanofiber lamps. The surface temperature of the lamps increased linearly with increment of a current to flow a lamp and revealing the increasing pattern as the length of the ramps is shorter. The proposed heating source was evaluated based on drying efficiency, moisture evaporation rate at laundry, and internal temperature of a drum during drying process. The drying efficiency satisfied a 45% which is specified in KS C 9319. The moisture evaporation rate and the internal temperature of the drum were respectively 98.88% and $61.1^{\circ}C$, which are similar to that of S's company dryer. From the evaluation and actual drying test results, the proposed carbon nanofiber lamp heating module is considered to be applicable as a heat source for laundry dryer in terms of drying efficiency and drying performance. it is possible to obtain a heat source at a high temperature, an excellent calorific value, an improvement in drying performance, and an effect of sterilizing laundry due to the emission of far-infrared rays. In addition to the applicability, the difference of the drying efficiency between the dryers was analyzed in detail based on the power consumption of the heat sources.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.4
• /
• pp.258-265
• /
• 2015

Over the last 20 years, freak waves have attracted many researchers because of their unexpected behaviors and damages on offshore structures and vessels in the ocean and coastal waters. Despite many researches on the causes, mechanisms and occurrence of freak waves, we have not reached consensus on the results of the researches. This paper presents the occurrence probability of freak waves based on the analysis of wave records measured at coastal waters of Donghae harbor in the East Sea. Three freak waves were found which satisfied conditions of m and $H_S{\geq}2.5m$ and $H_m/H_S{\geq}2$. The occurrence probabilities of freak waves were estimated from extreme distributions by Mori, Rayleigh and Ahn, and found to be on the orders of O($10^{-1}$), O($10^{-2}$), and O($10^{-3}$), respectively. The occurrence probabilities of freak waves measured from waves records were estimated between O($10^{-2}$) and O($10^{-3}$), which were located between predictions by Rayleigh and Ahn's extreme probability distributions. However, we need more analysis of wave records obtained from diverse field conditions in order to verify the accuracy of the estimation of occurrence probability of freak waves.

• Journal of Engineering Education Research
• /
• v.9 no.2
• /
• pp.34-51
• /
• 2006

In knowledge based society of 21c, engineers require not only their own speciality but also engineering basic competency such as creative thinking, the ability of working together, the ability of communication. Engineering colleges responsible for educating engineers consider developing curriculum including Engineering Basic Competency which is reflecting the needs of the times. By utilizing the accreditation programs of engineering education, UK-SPEC of UK Engineering Council, EA(Engineering Australia) standards/handbook of the Institute of Engineers Australia, O*NET of U.S. Occupational Network, this study generates core elements of engineering basic competency to prove the capability of engineering basic competency required to desired engineers. Core constituents derived from the study were categorized into 3 major areas of the basic engineering literacy in Humanities and Social Sciences(HSS), the ability of Creativity Engineering Design, Career development and each category and constituents were surveyed and checked by engineers in the field to deduce engineering basic competency that should be educated in the engineering college.

• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.269-275
• /
• 2004

Different biological tissues have different values of electrical resistivity. In EIT (electrical impedance tomography), we try to provide cross-sectional images of a resistivity distribution inside an electrically conducting subject such as the human body mainly for functional imaging. However, it is well known that the image reconstruction problem in EIT is ill-posed and the quality of a reconstructed image highly depends on the measurement error. This requires us to develop a high-performance EIT system. In this paper, we describe the development of a 16-channel digital EIT system including a single constant current source, 16 voltmeters, main controller, and PC. The system was designed and implemented using the FPGA-based digital technology. The current source injects 50KHz sinusoidal current with the THD (total harmonic distortion) of 0.0029% and amplitude stability of 0.022%. The single current source and switching circuit reduce the measurement error associated with imperfect matching of multiple current sources at the expense of a reduced data acquisition time. The digital voltmeter measuring the induced boundary voltage consists of a differential amplifier, ADC, and FPGA (field programmable gate array). The digital phase-sensitive demodulation technique was implemented in the voltmeter to maximize the SNR (signal-to-noise ratio). Experimental results of 16-channel digital voltmeters showed the SNR of 90dB. We used the developed EIT system to reconstruct resistivity images of a saline phantom containing banana objects. Based on the results, we suggest future improvements for a 64-channel muff-frequency EIT system for three-dimensional dynamic imaging of bio-impedance distributions inside the human body.

• Journal of Biomedical Engineering Research
• /
• v.28 no.3
• /
• pp.397-409
• /
• 2007

Owing to needs of biomechanical comprehension and analysis to obtain various medical treatment designs which are related with the spine in order to cure and diagnose LBP patients, the FE modeling and nonlinear analysis of lumbosacrum including a partial ilium and iliolumbar ligaments, were carried out. First, we investigated whether the geometrical configuration of vertebrae displayed by DICOM slice files is regular and normal condition. After constructing spinal vertebrae including a partial ilium, a sacrum and five lumbars (from L1 to L5)with anatomical shape reconstructed using softwares such as image modeler and CAD modeler, we added iliolumbar ligaments, lumbar ligaments, discs and facet joints, etc.. And also, we assigned material property and discretized the model using proper finite element types, thus it was completely modeled through the above procedure. For the verification of each segment, average sagittal ROM, average coronal ROM and average transversal ROM under various loading conditions(${\pm}10Nm$), average vertical displacement under compression(400N), ALL(Anterior Longitudinal Ligament) and PLL(Posterior Longitudinal Ligament) force at L12 level, strains of seven ligaments on sagittal plane at L45 level and maximal strain of disc fibers according to various loading conditions at L45 level, etc., they were compared with experimental results. For the verification of multilevel-lumbosacrum spine including partial ilium and iliolumbar ligaments, the cases with and without iliolumbar ligaments were compared with ROM of experiment. The results were obtained from analysis of the verified FE model as follows: I) Iliolumbar ligaments played a stabilizing role as mainly posterior iliolumbar ligaments under flexion and as both posterior and anterior iliolumbar ligaments of one side under lateral bending. 2) The iliolumbar ligaments decreased total ROM of 1-8% in total model according to various motion conditions, which changed facet contact forces of L5S level by approximately 0.8-1.4 times and disc forces of L5S level by approximately 0.8-1.5 times more than casewithout ilioligaments, under various loading conditions. 3) The force of lower discs such as L45 and L5S was bigger than upper discs under flexion, left and right bending and left and right twisting, except extension. 4) It was predicted that strains of posterior ligaments among iliolumbar ligaments would produce the maximum 16% under flexion and the maximum 10% under twisting. 5) It's expected that this present model applies to the development and design of artificial disc, since it was comparatively in agreement with the experimental datum.