• Journal of the Korean Geotechnical Society
• /
• v.32 no.2
• /
• pp.19-30
• /
• 2016

It is well known that water leakage from decrepit sewer pipe mainly causes frequent occurrence of ground subsidence in urban area. Thus, laboratory model tests were carried out to investigate ground behaviour according to location of sewer fracture and various relative densities of surrounding soil. The portion of fractured pipe was assumed to be 20% compared to the circumference of pipe, and to be positioned at the top and bottom of the pipe. Ground conditions were made as loose sand ($D_r=30%$) and dense sand ($D_r=70%$). In addition, comparison and analysis with results of model tests were carried out by Finite Element analysis. As a result, not only water leakage from the bottom of pipe (scenario 2) caused greater ground behaviour than leakage from the top of pipe (scenario 1), but also much greater surface settlement occurred when the ground condition is loose.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.1
• /
• pp.41-46
• /
• 2008

In this study, the analysis of load transition of PHC pile was performed with the static load test, which was driven in deep soft clay layer of MyungJi site in the western area of Pusan. The results of test showed that the range of unit side resistance of pile in sand layer were $7.4t/m^2$ to $23.3t/m^2$ and $6.4t/m^2$ in the soft clay layer, while the unit base resistance was $955t/m^2$ in dense silty sand layer. To select the most reasonable static bearing capacity formular, the field measured values are compared with the calculated ones from the suggested various formular. In the case of side resistance in sand layer, the suggest formular in the Structural Foundation Design Manual by KGS was most reasonable, while in clay layer Railroad Design Manual.

• Geophysics and Geophysical Exploration
• /
• v.7 no.1
• /
• pp.93-98
• /
• 2004

The sand-covered Muweilah archaeological site in the United Arab Emirates (UAE) is a unique Iron Age site, and has been subject to intensive investigations. However, excavations are time consuming and may require twenty years to complete. Thus geophysical surveys were undertaken with the objective of characterising the site more expeditiously. This paper presents preliminary results of these surveys. Ground penetrating radar (GPR) was tested as a primary imaging tool, with an ancillary shallow time domain EM (MetalMapper) system. Dense 3D GPR datasets were migrated to produce horizontal (plan view) depth slices at 10 cm intervals, which is conceptually similar to the archaeologists' excavation methodology. The objective was to map all features associated with anthropogenic activity. This required delineating extensive linear and planar features, which could represent infrastructure. The correlation between these and isolated point reflectors, which could indicate anthropogenic activity, was then assessed. Finally, MetalMapper images were used to discriminate between metallic and non-metallic scatterers. The moderately resistive sand cover allowed GPR depth penetration of up to 5 m with a 500 MHz system. GPR successfully mapped floor levels, walls, and isolated anthropogenic activity, but crumbling walls were difficult to track in some cases. From this study, two possible courtyard areas were recognised. The MetalMapper was less successful because of its limited depth penetration of 50 cm. Despite this, the system was still useful in detecting modem-day ferruginous waste and bronze artefacts. The results (subject to ongoing ground-truthing) indicated that GPR was optimal for sites like Muweilah, which are buried under a few metres of sand. The 3D survey methodology proved essential to achieve line-to-line correlation for tracking walls. In performing the surveys, a significant improvement in data quality ensued when survey areas were flattened and de-vegetated. Although MetalMapper surveys were not as useful, they certainly indicated the value of including other geophysical data to constrain interpretation of complex GPR features.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.2
• /
• pp.79-86
• /
• 2009

Concrete materials in nuclear facilities may become contaminated or activated by various radionuclides through different mechanism. Decommissioning and dismantling of these facilities produce considerable quantities such as concrete structure, rubble. In this paper, the characteristics distribution of the radionuclide have been investigated for the effects of the heating and grinding test for aggregate size such as gravel, sand and paste from decommissioning of the TRIGA MARK II research reactor and uranium conversion plant. The experimental results showed that most of the radionuclide could be removed from the gravel, sand aggregate and concentrated into a paste. Especially, we found that the heating temperature played an important role in separating the radionuclide from the concrete waste. Contamination of concrete is mainly concentrated in the porous paste and not in the dense aggregate such as the gravel and sand. The volume reduction rate could be achieved about 80% of activated concrete waste and about 75% of dismantled concrete waste generated from UCP.

• Asian Journal of Turfgrass Science
• /
• v.9 no.3
• /
• pp.187-198
• /
• 1995

The objective of this research was to produce sod by box seeding for zoysiagrass or by vegetative propagation for zoysiagrass and manilagrass.1 Various ratio of peatmoss to sand(v /v) were prepared to find idea[ medium for fast and light weight sod production. Then, the days required for sod formation, the effect of growth regulators on the growth of turfgrass, and the various storage methods for winter keeping of sods were also investigated. 1.The mixed medium of sand and peatmoss(v /v, 1 : 2) showed more biomass production than that of sand. 2.In comparison of seeding rate of zoysiagrass, the amount of log /$m^2$ was most effective in the fast and dense sod formation. The amount of 20g /$m^2$ also showed fast sod formation. But, it resulted in weak plant and less tillering. During April to June, about 100 days were required to form sod with seeding rate of 5g /$m^2$ regardless of seeding time. Whereas 80 days were required to form sod in the rate log /$m^2$, which was 20 days shorter than that of 5g /$m^2$. 3.More than 85% of shoots in sod stored in field or plastic house during the winter time resumed the growth in good appearance after transplanting. The whole covering of ground with sod resulted in less weeds and faster formation of lawn. 4.Vegetative propagation of manilagrass showed about 7 to 15 days faster formation of sod than that of zoysiagrass. Application of GA increased shoot growth and BA increased the total number of tillering. However, the effects of the combined application of GA and BA were negligable.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.27 no.5
• /
• pp.193-202
• /
• 2023

In this paper, a dynamic centrifuge model test was conducted on a 24.8-meter-deep excavation consisting of a 20 m sand layer and 4.8 m bedrock, classified as S3 by Korean seismic design code KDS 17 10 00. A braced excavation wall supports the hole. From the results, the mechanism of seismically induced earth pressure was investigated, and their distribution and loading points were analyzed. During earthquake loadings, active seismic earth pressure decreases from the at-rest earth pressure since the backfill laterally expands at the movement of the wall toward the active direction. Yet, the passive seismic earth pressure increases from the at-rest earth pressure since the backfill pushes to the wall and laterally compresses at it, moving toward a passive direction and returning to the initial position. The seismic earth pressure distribution shows a half-diamond distribution in the dense sand and a uniform distribution in loose sand. The loading point of dynamic thrust corresponding with seismic earth pressure is at the center of the soil backfill. The dynamic thrust increased differently depending on the backfill's relative density and input motion type. Still, in general, the dynamic thrust increased rapidly when the maximum horizontal displacement of the wall exceeded 0.05 H%.

• Advances in materials Research
• /
• v.11 no.2
• /
• pp.121-146
• /
• 2022

In the recent years, the use of agricultural waste in green cement mortar and concrete production has attracted considerable attention because of potential saving in the large areas of landfills and potential enhancement on the performance of mortar. In this research, microparticles of palm oil fuel ash (POFA) obtained from a multistage thermal and mechanical treatment processes of raw POFA originating from palm oil mill was utilized as a pozzolanic material to produce high-performance cement mortar (HPCM). POFA was used as a partial replacement material to ordinary Portland cement (OPC) at replacement levels of 0, 5, 10, 15, 20, 25, 30, 35, 40% by volume. Sand with particle size smaller than 300 ㎛ was used to enhance the performance of the HPCM. The HPCM mixes were tested for workability, compressive strength, ultrasonic pulse velocity (UPV), porosity and absorption. The results portray that the incorporation of micro POFA in HPCMs led to a slight reduction in the compressive strength. At 40% replacement level, the compressive strength was 87.4 MPa at 28 days which is suitable for many high strength applications. Although adding POFA to the cement mixtures harmed the absorption and porosity, those properties were very low at 3.4% and 11.5% respectively at a 40% POFA replacement ratio and after 28 days of curing. The HPCM mixtures containing POFA exhibited greater increase in strength and UPV as well as greater reduction in absorption and porosity than the control OPC mortar from 7 to 28 days of curing age, as a result of the pozzolanic reaction of POFA. Micro POFA with finely graded sand resulted in a dense and high strength cement mortar due to the pozzolanic reaction and increased packing effect. Therefore, it is demonstrated that the POFA could be used with high replacement ratios as a pozzolanic material to produce HPCM.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.123-130
• /
• 2011

In the precedent study it was presented that the comparison of thermal resistivity using various backfill materials including river sand regarding water content, dry unit weight and particle size distribution. Based on the precedent study, this study focused on developing the optimized backfill material that would improve the power transfer capability and minimize the thermal runaway due to an increase of power transmission capacity of underground power cables. When raw materials, such as river sand, recycled sand, crush rock and stone powder, are used for a backfill material, they has not efficient thermal resistivity around underground power cables. Thus, laboratory tests are performed by mixing Fly-ash, slag and floc with them, and then it is found that the optimized backfill material are required proper water content and maximum density. Through various experimental test, when coarse material, crush rock, is mixed with recycled sand, stone powder, slag or floc for a dense material, the thermal resistivity of it has $50^{\circ}C$-cm/Watt at optimum moisture content, and the increase of thermal resistivity does not happen in dry condition. The result of experiments approach the optimization of the backfill materials for underground power cables.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.119-124
• /
• 2002

Generally, Portland cement concrete(PCC) pavements have the advantage of durability and superior surface friction when compared to most dense-graded asphalt. However, It is known that PCC pavements create more noise than asphaltic surfaces due to the noise from interaction of tire and pavement surface. Recently exposed aggregate concrete(EAC) pavement was sugested to reduce traffic noise. So in this paper, we considered several materials and mixture proportions for proper depth of exposed aggregate which was measured by the sand patching test, and then according to those relationships, we tried to find out dosage of retarding agents and optimum mixture proportions for expecting good effects to noise reduction. It were also evaluated sound level at every conditions of surface texture as like depth of aggregate exposed, profile peak, distance of aggregate and types of aggregate.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2000.05a
• /
• pp.37-40
• /
• 2000

Acoustically enhanced soil flushing method is a newly developed in-situ remediation technique. However, there has not been an analytical method that can be used to evaluate the effectiveness of ultrasonic wave under different conditions. This study was undertaken to investigate the degree of enhancement in contaminant removal due to ultrasonic energy on the soil flushing method. The test conditions included different levels of ultrasonic power and hydraulic gradient. The test soils were Ottawa sand, a fine aggregate, and a natural soil, and the surrogate contaminant was a Crisco Vegetable Oil. The test results showed that sonication could increase contaminant removal significantly. Increasing sonication power increased pollutant removal. The faster the flow is, the smaller the degree of enhancement will be. The pollutants in dense soils are more difficult to be removed than in loose soils.