• 한국재료학회지
• /
• 제26권5호
• /
• pp.287-291
• /
• 2016

The effect of heat treatment on the microstructure and mechanical properties of cast Ti-6%Al-4%V alloy was investigated. Heat treatment of cast Ti-6Al-4V alloy was conducted by solution treatment at $950^{\circ}C$ for 30 min; this was followed by water quenching and then aging at $550^{\circ}C$ for 1 to 1440 min. The highest hardness of the heat-treated specimens was obtained by solution treatment and subsequent aging for 5 min due to precipitates of fine ${\alpha}$ that formed from retained ${\beta}$ phase. The tensile strength of this alloy increased without dramatic decrease of the ductility due to microstructural refinement resulting from the decomposition of ${\alpha}^{\prime}$ martensite into fine ${\alpha}$ and ${\beta}$ phases, and also due to the fine ${\alpha}$ phase formed from the retained ${\beta}$ phase by aging treatment for 5 min. In addition, this strengthening might be caused by the transformation induced plasticity (TRIP) effect, which is a strain-induced martensite transformation from the retained ${\beta}$ phase during deformation, and which occurs even after aging treatment at $550^{\circ}C$ for 5 min.

• 소성∙가공
• /
• 제32권2호
• /
• pp.53-60
• /
• 2023

A wide range of grain size was achieved in a Fe-Cr-Mn austenitic stainless steel (STS) by cold rolling and reversion annealing. The tensile characteristics of the STS were analyzed in terms of the dependence of strain induced martensitic (SIM) transformation on the grain size. In the ultrafine grain regime, the steel showed a high yield strength over 1 GPa, a discontinuous yielding, and a prolonged yield point elongation followed by considerable strain hardening. By increasing the grain size, the discontinuous yielding diminished and the yield point elongation decreased. The microstructural examination revealed that these tensile characteristics are closely related to the suppression of SIM transformation with decreasing the grain size. Especially, the prolonged yield point elongation of the ultrafine grained STS was found to be associated with development of unidirectional ε martensite bands. Based on the microstructural examination of the deformed microstructures, the rationalization of the grain size dependence of SIM transformation was suggested.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.378-381
• /
• 2008

The buckling behavior of cylindrical shape-memory alloy and aluminum tube is investigated at room temperature using a split Hopkinson pressure bar and an Instron hydraulic machine with a specially designed recording system. The shape-memory alloy at superelastic property regime buckles gradually in quasi-static loading, and fully recovers upon unloading. However, the buckling of aluminum tube is sudden and catastrophic, and shows permanent deformation. This gradual buckling of shape-memory alloy is associated with the forward and reverse transformation of stress-induced martensite and seems to have a profound effect on the unstable deformation of tube structures made from shape-memory alloy.

• Advances in nano research
• /
• 제13권4호
• /
• pp.313-323
• /
• 2022

The microstructure and mechanical properties of Cr-Ni steel and Cr-Ni steel-matrix nanocomposites reinforced with nano-ZrO₂ particles were investigated in this study. Cr-Ni steel and Cr-Ni/ZrO₂ nanocomposites were produced using a combination of high-energy ball milling, pressing, and sintering processes. The microstructures of the specimens were analyzed using EDX and XRD. Compression and hardness tests were performed to determine the mechanical properties of the specimens. Nano-ZrO₂ particles were effective in preventing chrome carbide precipitate at the grain boundaries. While t-ZrO₂ was detected in Cr-Ni/ZrO₂ nanocomposites, m-ZrO₂ could not be found. Few α'-martensite and deformation bands were formed in the microstructures of Cr-Ni/ZrO₂ nanocomposites. Although nano-ZrO₂ particles had a negligible impact on the strength improvement provided by deformation-induced plasticity mechanisms in Cr-Ni/ZrO₂ nanocomposites, the mechanical properties of Cr-Ni steel were significantly improved by using nano-ZrO₂ particles. The hardness and compressive strength of Cr-Ni/ZrO₂ nanocomposite were higher than those of Cr-Ni steel and enhanced as the weight fraction of nano-ZrO₂ particles increased. Cr-Ni/ZrO₂ nanocomposite with 5wt.% nano-ZrO₂ particles had almost twofold the hardness and compressive strength of Cr-Ni steel. The nano-ZrO₂ particles were considerably more effective on particle-strengthening mechanisms than deformation-induced strengthening mechanisms in Cr-Ni/ZrO₂ nanocomposites.

• 한국재료학회지
• /
• 제29권3호
• /
• pp.189-195
• /
• 2019

The effect of C, Mn, and Al additions on the tensile and Charpy impact properties of austenitic high-manganese steels for cryogenic applications is investigated in terms of the deformation mechanism dependent on stacking fault energy and austenite stability. The addition of the alloying elements usually increases the stacking fault energy, which is calculated using a modified thermodynamic model. Although the yield strength of austenitic high-manganese steels is increased by the addition of the alloying elements, the tensile strength is significantly affected by the deformation mechanism associated with stacking fault energy because of grain size refinement caused by deformation twinning and mobile dislocations generated during deformation-induced martensite transformation. None of the austenitic high-manganese steels exhibit clear ductile-brittle transition behavior, but their absorbed energy gradually decreases with lowering test temperature, regardless of the alloying elements. However, the combined addition of Mn and Al to the austenitic high-manganese steels suppresses the decrease in absorbed energy with a decreasing temperature by enhancing austenite stability.

• 열처리공학회지
• /
• 제7권2호
• /
• pp.118-128
• /
• 1994

Five alloys were selected randomly in the composition range showing the best shape memory effect in Fe-Mn-Si system reported by Murakami. The shape memory effects of those alloys were mainly investigated through the training treatment which consisted of the repetition of 2% tensile deformation at room temperature and subsequent annealing at $600^{\circ}C$ above $A_r$ temperature. At the same deformation degress in rolling $600^{\circ}C$-annealing for 1 hr. showed the best shape memory effect, and 10%-deformation degrees represented maxima of the shpae memory effects at all annealing temperatures, $500^{\circ}C$, $600^{\circ}C$ and $700^{\circ}C$. The shape memory effects of the alloys were increased by increasing training cycle up to 5 cycles. This was because a large number of dislocations introduced by training process gave rise to increase in the austenite yield stress, and acted as nucleation sites for stress induced ${\varepsilon}$ martensite. The thermal cycling treatment, repetition of cooling in nitrogen at $-196{\circ}C$ and heating to $300^{\circ}C$ for 5 min., did not improve the shape memory effect.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.323-326
• /
• 2001

NI$_2$MnGa-based ferromagnetic shape memory alloys (FSMA) are hoped to be used as robust actuators with high performance and power density, as a replacement of other actuation materials such as thermo-mechanical SMAs and mechanical-electric piezoelectrics. Recently, we have observed significant shape changes under magnetic field application when single- and poly-crystalline forms are used. In the present study, two mechanisms have been proposed to predict the magnetic field-induced shape change as a function of external magnetic field at temperatures below Mr and above Ar. In the case of the field-induced shape change at temperature below M$_{f}$, paired martensite variants are assumed to form by application of magnetic field. The direction of magnetization in martensites formed in austenite matrix is assumed to be parallel to the applied magnetic field in the case of shape change by application at temperature above Af. Various energies has been considered in the shape change under two mechanisms.s.

• 한국압력기기공학회 논문집
• /
• 제16권2호
• /
• pp.58-67
• /
• 2020

This study presents cyclic stress-strain and tensile test results at room temperature (RT) and 316℃ using cold-worked TP304 stainless steel base and weld metals. By comparing the cyclic hardening/softening behavior and failure cycle of cold-worked materials with those of irradiated austenitic stainless steels, the feasibility of simulating the irradiation effect on cyclic deformation and failure behaviors of TP304 stainless steel base and weld metals was investigated. It was found that, in the absence of strain-induced martensite trasformation, cold-working could properly simulate the change in cyclic hardening/softening behavior of TP304 stainless steel base and weld metals due to neutron irradiation. It was also recognized that cold-working could adequately simulate the reduction in failure cycles of TP304 stainless steel base and weld metals due to neutron irradition in the low-cycle fatigue region.

• 소성∙가공
• /
• 제19권8호
• /
• pp.468-473
• /
• 2010

Shape memory alloys (SMAs) have the ability to recover their original shape upon thermo-mechanical loading even after large inelastic deformation. The unique feature is known as pseudoelasticity and shape memory effect caused by the crystalline structural transformation between two solid-state phases called austenite and martensite. To support the engineering application, a number of constitutive models, which can be formally classified into either micromechanics-based or phenomenological model, have been developed. Most of the constitutive models include a kinetic law governing the crystallographic transformation. The present work presents a one-dimensional, phenomenological constitutive model for SMAs in the context of the unified viscoplasticity theory. The proposed model does not incorporate the complex mechanisms of phase transformation. Instead, the effects induced by the transformation are depicted through the growth law for the back stress that is an internal state variable of the model.

• 대한기계학회논문집
• /
• 제7권2호
• /
• pp.123-129
• /
• 1983

The effect of the micro-internal stress which is induced in the ferrite grain by plastic constraint, on fracture behavior was investigated. The specimen used has combined microstructure with matrix of ferrite encapsulated by second phase of martensite. The micro-internal stress in the ferrite grain was estimated using a simple mechanical model, and its effect on micro and macro fracture behaviors was discussed. The results obtained are summarized as follows; The micro-internal stress promotes the formation of cleavage cracks in the ferrite during deformation. Consequently, it was concluded that the internal stress is one of the significant factors which cause the fracture ductility to decrease.